Introduction
Introduction Statistics Contact Development Disclaimer Help
View Source
# PIICEON, INC.
DISPATCHER 805-3400
Card Type Modem (asynchronous)
Chipset Rockwell
Maximum Data Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus Compaq communications bus
Fax Class Class I & II
Data Modulation Bell 103A/212A
ITU-T V.21, V.22, V.23, V.22bis, V.32,
V.32bis, V.34
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line out | CN1 | Compaq communications bus | CN3 |
|---------------+----------+---------------------------+-----|
| Line in | CN2 | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, ‘comma’, A/ |
|------------------------------------------------------------|
| A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, |
| &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \G, \J, \L, \W |
|------------------------------------------------------------|
| %C, %F, %L, %Q |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, |
| S16, S18, S21, S22, S23, S24, S25, S27, |
|------------------------------------------------------------|
| S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, |
| S46, S48, S82, S86, S91, S92, S95, S201 |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| -K, -Q, *H, )M, @M, :E, #CID |
|------------------------------------------------------------|
| Note: See MHI help file for full command |
| documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures action of break signal |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \K0 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| \K1 | Break sent to remote modem and buffered |
| | cleared. |
|--------------+---------------------------------------------|
| \K2 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| \K3 | Send break to remote modem immediately. |
|--------------+---------------------------------------------|
| \K4 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| í \K5 | Send break with transmitted data. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Pn:xxxx:<#> |
|--------------+---------------------------------------------|
| Description: | Stores the information for callback number |
| | n. When enabled, the modem will call back |
| | the phone number indicated and request the |
| | matching password. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR DRIVER DOWNLOAD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^C2 |
|--------------+---------------------------------------------|
| Description: | Initiates an ASCII transfer of a new |
| | cellular phone driver. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR DRIVER INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^I [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information about the currently |
| | loaded cellular phone driver. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR PHONE STATUS |
|------------------------------------------------------------|
| Type: | Immediate |
|------------------------------------------------------------|
| Format: | AT [cmds] ^T6 [cmds] |
|-----------------+------------------------------------------|
| Description: | Displays the current status of the |
| | connected cellular phone. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+--------+---------------------------------------|
| 0 | 0 | Cellular phone is not receiving an |
| | | incoming call. |
| | 1 | |
| | | Cellular phone is receiving an |
| | | incoming call. |
|-----------+--------+---------------------------------------|
| 1 | 0 | Cellular phone is not in use. |
| | | |
| | 1 | Cellular phone is in use. |
|-----------+--------+---------------------------------------|
| 2 | 0 | Cellular phone is not locked. |
| | | |
| | 1 | Cellular phone is locked. |
|-----------+--------+---------------------------------------|
| 3 | 0 | Cellular service present. |
| | | |
| | 1 | Cellular service not present. |
|-----------+--------+---------------------------------------|
| 4 | 0 | Cellular phone is off. |
| | | |
| | 1 | Cellular phone is on. |
|-----------+--------+---------------------------------------|
| 5 | 0 | Cellular driver is not initialized. |
| | | |
| | 1 | Cellular driver is initialized. |
|-----------+--------+---------------------------------------|
| 6 | 0 | Not used. |
|-----------+--------+---------------------------------------|
| 7 | 0 | Cellular cable not detected. |
| | | |
| | 1 | Cellular cable detected. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will connect with. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Modem will connect in normal mode. |
|--------------+---------------------------------------------|
| \N1 | Modem will connect in normal mode. |
|--------------+---------------------------------------------|
| \N2 | Modem will attempt V.42bis mode, then MNP |
| | mode, then hang up. |
|--------------+---------------------------------------------|
| í \N3 | Modem will attempt V.42bis mode, then MNP |
| | mode, then normal mode. |
|--------------+---------------------------------------------|
| \N4 | Modem will attempt V.42bis mode, then hang |
| | up. |
|--------------+---------------------------------------------|
| \N5 | Modem will attempt MNP mode, then hang up. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string. |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DJ | MNP10 link will be negotiated at 1200bps |
| | for this call. |
|--------------+---------------------------------------------|
| DK | MNP10 power level adjustment enabled for |
| | this call. |
|--------------+---------------------------------------------|
| DL | Re-dial last number. |
|--------------+---------------------------------------------|
| DP | Dial following digits in pulse mode. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n. |
|--------------+---------------------------------------------|
| DT | Dial following digits in tone mode. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register. |
|--------------+---------------------------------------------|
| D"WXY" | Optional method of denoting telephone |
| | numbers. Letters enclosed in quotes are |
| | interpreted as numbers according to the |
| | system found on a telephone keypad. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D& | Wait for AT&T credit card ("bong") tone |
| | detection function enabled. Waits for bong |
| | tone for amount of time specified by the S7 |
| | command. |
|--------------+---------------------------------------------|
| D$ | Wait for prompt tone detection function |
| | enabled. Waits for prompt tone for amount |
| | of time specified by the S7 command. |
|--------------+---------------------------------------------|
| D^ | Toggles calling tone on or off for this |
| | call. |
|--------------+---------------------------------------------|
| D> | Sends grounding pulse on EARTH relay line. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \F [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all stored numbers. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] +DMS=x,y,z,a [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets options for active protocol; the |
| | transfer rates specified by z and a must be |
| | valid for the protocol selected. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| x=0 | Set protocol to V.21. |
|--------------+---------------------------------------------|
| x=1 | Set protocol to V.22. |
|--------------+---------------------------------------------|
| x=2 | Set protocol to V.22bis. |
|--------------+---------------------------------------------|
| x=3 | Set protocol to V.23. |
|--------------+---------------------------------------------|
| x=9 | Set protocol to V.32. |
|--------------+---------------------------------------------|
| x=10 | Set protocol to V.32bis. |
|--------------+---------------------------------------------|
| x=11 | Set protocol to V.34. |
|--------------+---------------------------------------------|
| x=64 | Set protocol to Bell 103. |
|--------------+---------------------------------------------|
| x=69 | Set protocol to Bell 212A. |
|--------------+---------------------------------------------|
| y=0 | Automode disabled. |
|--------------+---------------------------------------------|
| y=1 | Auto-detect highest speed enabled |
|--------------+---------------------------------------------|
| y=2 | Unidentified. |
|--------------+---------------------------------------------|
| z, a=300 | Set minimum or maximum transfer rate at |
| | 300bps, respectively. |
|--------------+---------------------------------------------|
| z, a=1200 | Set minimum or maximum transfer rate at |
| | 1200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=2400 | Set minimum or maximum transfer rate at |
| | 2400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=4800 | Set minimum or maximum transfer rate at |
| | 4800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=7200 | Set minimum or maximum transfer rate at |
| | 7200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=9600 | Set minimum or maximum transfer rate at |
| | 9600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=12000 | Set minimum or maximum transfer rate at |
| | 12000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=14400 | Set minimum or maximum transfer rate at |
| | 14400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=16800 | Set minimum or maximum transfer rate at |
| | 16800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=19200 | Set minimum or maximum transfer rate at |
| | 19200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=21600 | Set minimum or maximum transfer rate at |
| | 21600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=24000 | Set minimum or maximum transfer rate at |
| | 24000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=26400 | Set minimum or maximum transfer rate at |
| | 26400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=28800 | Set minimum or maximum transfer rate at |
| | 28800bps, respectively. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION END |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *E [cmds] |
|--------------+---------------------------------------------|
| Description: | Ends the current remote configuration |
| | session. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Cxxxx [cmds] |
|--------------+---------------------------------------------|
| Description: | Stores the password that must be sent by a |
| | remote modem to enter a remote |
| | configuration session on the local modem. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION REQUEST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Requests the remote modem to start a remote |
| | configuration session. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports modem model and speed. |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum. |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum. |
|--------------+---------------------------------------------|
| I3 | Reports firmware revision. |
|--------------+---------------------------------------------|
| I4 | Reports OEM identifer. |
|--------------+---------------------------------------------|
| I5 | Reports country code. |
|--------------+---------------------------------------------|
| I6 | Reports data pump and ROM revision. |
+------------------------------------------------------------+
You are viewing proxied material from bitreich.org. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.