PIICEON, INC.
=============
DISPATCHER 805-3400
Card Type Modem (asynchronous)
Chipset Rockwell
Maximum Data Rate 28.8Kbps
Maximum Fax Rate 14.4Kbps
Data Bus Compaq communications bus
Fax Class Class I & II
Data Modulation Bell 103A/212A
ITU-T V.21, V.22, V.23, V.22bis, V.32,
V.32bis, V.34
Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29
Error MNP5, MNP10, V.42, V.42bis
Correction/Compression
<
gopher://bitreich.org/I/th99/t/P-R/52662-1.png>
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Label | Function | Label |
|------------------------------------------------------------|
| Line out | CN1 | Compaq communications bus | CN3 |
|---------------+----------+---------------------------+-----|
| Line in | CN2 | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SUPPORTED STANDARD COMMANDS |
|------------------------------------------------------------|
| Basic AT Commands |
|------------------------------------------------------------|
| +++, 'comma', A/ |
|------------------------------------------------------------|
| A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z |
|------------------------------------------------------------|
| &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, |
| &Y, &Z |
|------------------------------------------------------------|
| Extended AT Commands |
|------------------------------------------------------------|
| \A, \B, \G, \J, \L, \W |
|------------------------------------------------------------|
| %C, %F, %L, %Q |
|------------------------------------------------------------|
| S-Registers |
|------------------------------------------------------------|
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, |
| S16, S18, S21, S22, S23, S24, S25, S27, |
|------------------------------------------------------------|
| S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, |
| S46, S48, S82, S86, S91, S92, S95, S201 |
|------------------------------------------------------------|
| Special AT Commands |
|------------------------------------------------------------|
| -K, -Q, *H, )M, @M, :E, #CID |
|------------------------------------------------------------|
| Note: See MHI help file for full command |
| documentation. |
+------------------------------------------------------------+
Proprietary AT Command Set
+------------------------------------------------------------+
| BREAK TYPE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Kn [cmds] |
|--------------+---------------------------------------------|
| Description: | Configures action of break signal |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \K0 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| \K1 | Break sent to remote modem and buffered |
| | cleared. |
|--------------+---------------------------------------------|
| \K2 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| \K3 | Send break to remote modem immediately. |
|--------------+---------------------------------------------|
| \K4 | Online command mode enabled, do not send |
| | break to remote modem. |
|--------------+---------------------------------------------|
| i \K5 | Send break with transmitted data. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CALLBACK |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Pn:xxxx:<#> |
|--------------+---------------------------------------------|
| Description: | Stores the information for callback number |
| | n. When enabled, the modem will call back |
| | the phone number indicated and request the |
| | matching password. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR DRIVER DOWNLOAD |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^C2 |
|--------------+---------------------------------------------|
| Description: | Initiates an ASCII transfer of a new |
| | cellular phone driver. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR DRIVER INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] ^I [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information about the currently |
| | loaded cellular phone driver. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CELLULAR PHONE STATUS |
|------------------------------------------------------------|
| Type: | Immediate |
|------------------------------------------------------------|
| Format: | AT [cmds] ^T6 [cmds] |
|-----------------+------------------------------------------|
| Description: | Displays the current status of the |
| | connected cellular phone. |
|------------------------------------------------------------|
| Bit | Value | Function |
|-----------+--------+---------------------------------------|
| 0 | 0 | Cellular phone is not receiving an |
| | | incoming call. |
| | 1 | |
| | | Cellular phone is receiving an |
| | | incoming call. |
|-----------+--------+---------------------------------------|
| 1 | 0 | Cellular phone is not in use. |
| | | |
| | 1 | Cellular phone is in use. |
|-----------+--------+---------------------------------------|
| 2 | 0 | Cellular phone is not locked. |
| | | |
| | 1 | Cellular phone is locked. |
|-----------+--------+---------------------------------------|
| 3 | 0 | Cellular service present. |
| | | |
| | 1 | Cellular service not present. |
|-----------+--------+---------------------------------------|
| 4 | 0 | Cellular phone is off. |
| | | |
| | 1 | Cellular phone is on. |
|-----------+--------+---------------------------------------|
| 5 | 0 | Cellular driver is not initialized. |
| | | |
| | 1 | Cellular driver is initialized. |
|-----------+--------+---------------------------------------|
| 6 | 0 | Not used. |
|-----------+--------+---------------------------------------|
| 7 | 0 | Cellular cable not detected. |
| | | |
| | 1 | Cellular cable detected. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| CONNECT MODE |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \Nn [cmds] |
|--------------+---------------------------------------------|
| Description: | Controls the type of connection the modem |
| | will connect with. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| \N0 | Modem will connect in normal mode. |
|--------------+---------------------------------------------|
| \N1 | Modem will connect in normal mode. |
|--------------+---------------------------------------------|
| \N2 | Modem will attempt V.42bis mode, then MNP |
| | mode, then hang up. |
|--------------+---------------------------------------------|
| i \N3 | Modem will attempt V.42bis mode, then MNP |
| | mode, then normal mode. |
|--------------+---------------------------------------------|
| \N4 | Modem will attempt V.42bis mode, then hang |
| | up. |
|--------------+---------------------------------------------|
| \N5 | Modem will attempt MNP mode, then hang up. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DIAL |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] D<#> [cmds] |
|--------------+---------------------------------------------|
| Description: | Dials telephone number according to any |
| | modifiers included in the string. |
|--------------+---------------------------------------------|
| Note: | Any combination of modifiers can be used to |
| | produce the desired dial functions in |
| | sequence. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| DJ | MNP10 link will be negotiated at 1200bps |
| | for this call. |
|--------------+---------------------------------------------|
| DK | MNP10 power level adjustment enabled for |
| | this call. |
|--------------+---------------------------------------------|
| DL | Re-dial last number. |
|--------------+---------------------------------------------|
| DP | Dial following digits in pulse mode. |
|--------------+---------------------------------------------|
| DS=n | Dial stored telephone number n. |
|--------------+---------------------------------------------|
| DT | Dial following digits in tone mode. |
|--------------+---------------------------------------------|
| DW | Dialing resumed following dial tone |
| | detection. |
|--------------+---------------------------------------------|
| D, | Dialing paused for amount of time specified |
| | in S8 register. |
|--------------+---------------------------------------------|
| D"WXY" | Optional method of denoting telephone |
| | numbers. Letters enclosed in quotes are |
| | interpreted as numbers according to the |
| | system found on a telephone keypad. |
|--------------+---------------------------------------------|
| D! | Flash function initiated. Modem commanded |
| | to go off-hook for specified time before |
| | returning on-hook. |
|--------------+---------------------------------------------|
| D@ | Wait for Quiet Answer function enabled. |
| | Modem waits until a "quiet answer," a |
| | ring-back signal followed by silence up to |
| | the time specified in S7, is received prior |
| | to executing the rest of the dial string. |
|--------------+---------------------------------------------|
| D& | Wait for AT&T credit card ("bong") tone |
| | detection function enabled. Waits for bong |
| | tone for amount of time specified by the S7 |
| | command. |
|--------------+---------------------------------------------|
| D$ | Wait for prompt tone detection function |
| | enabled. Waits for prompt tone for amount |
| | of time specified by the S7 command. |
|--------------+---------------------------------------------|
| D^ | Toggles calling tone on or off for this |
| | call. |
|--------------+---------------------------------------------|
| D> | Sends grounding pulse on EARTH relay line. |
|--------------+---------------------------------------------|
| D; | Modem returned to idle state after dialing. |
| | The semicolon can only be placed at the end |
| | of the dial command. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| DISPLAY STORED NUMBERS |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] \F [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays all stored numbers. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MODULATION SELECTION |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] +DMS=x,y,z,a [cmds] |
|--------------+---------------------------------------------|
| Description: | Sets options for active protocol; the |
| | transfer rates specified by z and a must be |
| | valid for the protocol selected. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| x=0 | Set protocol to V.21. |
|--------------+---------------------------------------------|
| x=1 | Set protocol to V.22. |
|--------------+---------------------------------------------|
| x=2 | Set protocol to V.22bis. |
|--------------+---------------------------------------------|
| x=3 | Set protocol to V.23. |
|--------------+---------------------------------------------|
| x=9 | Set protocol to V.32. |
|--------------+---------------------------------------------|
| x=10 | Set protocol to V.32bis. |
|--------------+---------------------------------------------|
| x=11 | Set protocol to V.34. |
|--------------+---------------------------------------------|
| x=64 | Set protocol to Bell 103. |
|--------------+---------------------------------------------|
| x=69 | Set protocol to Bell 212A. |
|--------------+---------------------------------------------|
| y=0 | Automode disabled. |
|--------------+---------------------------------------------|
| y=1 | Auto-detect highest speed enabled |
|--------------+---------------------------------------------|
| y=2 | Unidentified. |
|--------------+---------------------------------------------|
| z, a=300 | Set minimum or maximum transfer rate at |
| | 300bps, respectively. |
|--------------+---------------------------------------------|
| z, a=1200 | Set minimum or maximum transfer rate at |
| | 1200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=2400 | Set minimum or maximum transfer rate at |
| | 2400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=4800 | Set minimum or maximum transfer rate at |
| | 4800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=7200 | Set minimum or maximum transfer rate at |
| | 7200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=9600 | Set minimum or maximum transfer rate at |
| | 9600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=12000 | Set minimum or maximum transfer rate at |
| | 12000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=14400 | Set minimum or maximum transfer rate at |
| | 14400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=16800 | Set minimum or maximum transfer rate at |
| | 16800bps, respectively. |
|--------------+---------------------------------------------|
| z, a=19200 | Set minimum or maximum transfer rate at |
| | 19200bps, respectively. |
|--------------+---------------------------------------------|
| z, a=21600 | Set minimum or maximum transfer rate at |
| | 21600bps, respectively. |
|--------------+---------------------------------------------|
| z, a=24000 | Set minimum or maximum transfer rate at |
| | 24000bps, respectively. |
|--------------+---------------------------------------------|
| z, a=26400 | Set minimum or maximum transfer rate at |
| | 26400bps, respectively. |
|--------------+---------------------------------------------|
| z, a=28800 | Set minimum or maximum transfer rate at |
| | 28800bps, respectively. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION END |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *E [cmds] |
|--------------+---------------------------------------------|
| Description: | Ends the current remote configuration |
| | session. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION PASSWORD |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Cxxxx [cmds] |
|--------------+---------------------------------------------|
| Description: | Stores the password that must be sent by a |
| | remote modem to enter a remote |
| | configuration session on the local modem. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REMOTE CONFIGURATION REQUEST |
|------------------------------------------------------------|
| Type: | Configuration |
|--------------+---------------------------------------------|
| Format: | AT [cmds] *Rn [cmds] |
|--------------+---------------------------------------------|
| Description: | Requests the remote modem to start a remote |
| | configuration session. |
+------------------------------------------------------------+
+------------------------------------------------------------+
| REPORT INFORMATION |
|------------------------------------------------------------|
| Type: | Immediate |
|--------------+---------------------------------------------|
| Format: | AT [cmds] In [cmds] |
|--------------+---------------------------------------------|
| Description: | Displays information requested. |
|--------------+---------------------------------------------|
| Command | Function |
|--------------+---------------------------------------------|
| I0 | Reports modem model and speed. |
|--------------+---------------------------------------------|
| I1 | Reports ROM checksum. |
|--------------+---------------------------------------------|
| I2 | Tests and reports ROM checksum. |
|--------------+---------------------------------------------|
| I3 | Reports firmware revision. |
|--------------+---------------------------------------------|
| I4 | Reports OEM identifer. |
|--------------+---------------------------------------------|
| I5 | Reports country code. |
|--------------+---------------------------------------------|
| I6 | Reports data pump and ROM revision. |
+------------------------------------------------------------+
