ADDRESS 0100 THRU 0106
OLDVIEW -- THIS CHIP READS THE SEED KEYS AND THE MONTHLY KEYS
          INSTALL IN VCII PRESS "3" THEN "1" TO READ SEED KEYS.
          IF SEED KEYS ARE ALL 0000 THEN TURN OFF PWR TO VCII,
          AND TRY AGAIN.
          PRESS "4" TO READ MONTH 1 KEYS AND "6" TO READ MONTH 2
          KEYS. THE CONVERT 2100 OPTION IS NOT USED UNLESS YOU
          WISH TO INSTALL A FACT-02 OR FACT-04 (BOTH VERSIONS OF
          THE ORIGINAL FACTORY PROMS) INTO A 2100.
          THE REMOVE PASSWORD OPTION WILL RESET YOUR PASSWORD IF YOU
          FORGOT IT.
          NOTE! - IF THE MONTHLY KEYS ARE READ FROM AN AUTHORIZED
                  BOARD, THEN YOU CAN GET A QUICK TURN ON TO THE
                  CLONED UNIT AND NOT HAVE TO WAIT FOR THE SELDOM
                  SENT MONTHLY CODES.
WRITOLD -- THIS PROGRAM IS WHERE YOU ENTER THE DATA OBTAINED IN THE
          OLDVIEW PROCESS. IT WILL IN TURN CREATE A FILE CALLED
          WRITER.HEX, WHICH YOU MUST TURN INTO A BINARY FILE TO
          BURN INTO A 27128 EPROM FOR USE AS A CLONE-WRITER.
          NOTE! - TO EXECUTE THIS PROGRAM, YOU MUST FIRST USE A
                  WORD-PROCESSOR OR TEXT EDITOR TO BUILD A FILE
                  THAT LOOKS JUST LIKE SAMPLE.KEY BUT USING THE DATA
                  FROM OLDVIEW.
          THE COMMANDS SHOULD BE AS FOLLOWS:
          1:  TYPE --- WRITOLD XXXXXXXX.KEY (X = KEYS FROM OLDVIEW)
          2:  REPLY Y/N TO QUESTIONS YOU ARE ASKED.
          3:  CONVERT THE WRITER.HEX TO A BINARY FILE ( A PROGRAM
              SUCH AS DEBUG CAN DO THIS).
          4:  MAKE A EPROM FROM THE CONVERTED FILE TO USE AS YOUR
              CLONE-WRITER.
          5:  FOLLOWS SREEN INSTRUCTIONS AFTER CLONEING BY PRESSING
              THE TEXT KEY.
          6:  HAPPY CLONEING!!!!!!
WRITSML -  USE THIS PROGRAM THE SAME AS WRITOLD TO CREATE A CLONE-
          TER, WITH THE EXCEPTION THAT YOUR MONTHLY KEYS ARE OUT OF
          DATE AND ARE NOT AUTHORIZED. A LITTLE QUICKER TO MAKE.
OLDCLRAT - THIS IS A 3-MUSKATEER YOU CAN USE IN A CLONE OR BASE
          DECODER, IF IT DOES NOT TURN ON IMMEDIATELY, LEAVE IT
          ON UNTIL IT DOES. THE DELAY IS ONLY ON THE FIRST TURN
          ON AND IS CAUSED BY THE PASSWORD LEVEL OF "AAAA".
          IT USEALLY TAKES A FEW HOURS BUT HAS BEEN SEVERAL DAYS.
          BOY GI SURE KNOWS HOW TO INCONVIENCE A PIRATE DON'T THEY?
          NO PAY PER VIEW ON THIS CHIP!
          THIS CHIP CAN BE USED TO PUT ANY ADDRESS ON THE SCREEN AS
          THE UNIT ID# BY CHANGING THE DATA IN LOCATION $
OLDMRAT -  THIS IS A 3-MUSKATEER JUST LIKE OLDCRAT BUT IT LETS THE
          BASE ID# OF THE BOARD SHOW THRU TO THE SCREEN.
OLDPPV -   THIS IS A PAY PER VIEW 3-M USED TO MAKE A PPV FOR A
          PARTICULAR BOARD BY DOING THE FOLLOWING:
          1:  USING THE SEED KEYS FROM THE BOARD THAT THE CHIP
              IS TO GO INTO, MODIFY THE PROGRAM IN THIS CHIP
              AT STARTING LOC $ 3F00 WITH THE DATA FROM THE SEED
              KEYS BUT LEAVE OFF THE SEED KEY #. (EACH IS NUMBERED
              EITHER 00,01,02 OR 03) THIS DATA WAS OBTAINED IN THE
              OPTION "1" OF OLDVIEW. REMEMBER TO SKIP THE SEED KEY
              NUMBERS AND JUST INCLUDE THE DATA.
          NOTE! - THE PROGRAM IS LOADED AT $0000.
          2.  AT THE END OF THE SEED KEYS, ENTER THE UNIT ID JUST
              AS IT APPEARS IN OLDVIEW.
          3.  IF YOU ENTERED THE DATA CORRECTLY, YOU SHOULD FINISH
              AT LOC $3F1E.
          4.  THERE IS NO WAITING OR PASSWORD DELAYS WITH THIS CHIP.
PPVPASS -  ANOTHER PAY PER VIEW TOY BUT OLDPPV IS BETTER. SEE THE
          READ.ME FILE FOR DETAILS.
MAKEPPV -  PART OF PPVPASS SEE READ.ME
READ.ME -  DETAILS ON PPVPASS.
ROLLNG# -  YOU MAY REMEMBER THE 3-MUSKATEER THAT HAD ROLLING NUMBERS
          IN THE UNIT ID#, WELL THIS IS IT!
FACT-02 -  THE FIRST REV LEVEL OF FACTORY PROM INSTALLED IN THE
          MODEL 2000.
FACT-04 -  THE SECOND (AND ONLY OTHER) REV LEVEL OF FACTORY PROM
          INSTALLED IN THE MODEL 2000.
          YOU MAY REMEMBER THESE LEVELS AS 3.4 ETC.
SAMPLE -   A SAMPLE OF WHAT A KEYFILE SHOULD LOOK LIKE WHEN YOU BUILD
          ONE WITH A TEXT EDITOR OR WORD PROCESSOR.
NEWVIEW -  INSTALL THIS INTO THE 018 STYLE BOARD THAT YOU WISH TO
          READ THE KEY DATA FROM. THIS BOARD SHOULD BE CONTROLLED BY
          YOU AND THIS DATA WILL BE USED IN EACH OF THE 018
          BOARDS THAT YOU TURN ON.
WRITNEW -  RUN THIS PROGRAM AND ANSWER IT'S QUESTIONS USING THE
          DATA OBTAINED FROM NEWVIEW AND THE PASSWORDS GIVEN TO
          YOU. THEN IT WILL CREATE A FILE CALLED WRITER.BIN
          WHICH WILL BE THE FIRST CHIP YOU INSTALL IN AN 018
          ---AFTER--- YOU GET IT BACK FROM US!
          WHEN WRITER.BIN IS INSTALLED IN A VCII, IT WILL
          SAY UNIT CONVERTED ON THE SCREEN AND YOU MAY REMOVE IT
          FROM THE BOARD.
MAKMOUSE - THIS CHIP IS INSTALLED IN THE 018 AFTER YOU HAVE CONVERTED
          IT.  AND SHOULD NEVER BE REMOVED, TO REMOVE THIS CHIP
          WILL CAUSE THE BOARD TO QUIT WORKING AND WILL SET A FLAG
          THAT TELLS US WHAT YOU DID. WE WILL CHARGE YOU MORE THAN
          FULL PRICE TO TURN IT BACK ON AND BELIEVE ME IT WORKS!!
          --- NEVER   NEVER   NEVER   NEVER   NEVER   NEVER  NEVER -
          REMOVE THIS CHIP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!



   NOTE!!!!!!!!!!!
NEW NAMES FOR SOME OF THESE PROGRAMS ARE:

NEWVIEW WAS CALLED DEALVIEW

WRITNEW WAS CALLED WRITER

MAKMOUSE WAS CALLED MOUSE

OTHER OLDER PROBLEMS MAY ALSO BE RENAMED, I JUST LOVE CHANGE,
DON"T YOU????????

Downloaded From P-80 International Information Systems 304-744-2253

You are viewing proxied material from infinitelyremote.com. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.