Network Working Group J. Flick
Request for Comments: 2266 Hewlett Packard Company
Category: Standards Track January 1998
Definitions of Managed Objects for IEEE 802.12 Repeater Devices
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in TCP/IP-based internets.
In particular, it defines objects for managing network repeaters
based on IEEE 802.12.
Table of Contents
1. The SNMP Network Management Framework ...................... 2
1.1. Object Definitions ....................................... 2
2. Overview ................................................... 2
2.1. Repeater Management Model ................................ 3
2.2. MAC Addresses ............................................ 4
2.3. Master Mode and Slave Mode ............................... 4
2.4. IEEE 802.12 Training Frames .............................. 4
2.5. Structure of the MIB ..................................... 6
2.5.1. Basic Definitions ...................................... 7
2.5.2. Monitor Definitions .................................... 7
2.5.3. Address Tracking Definitions ........................... 7
2.6. Relationship to other MIBs ............................... 7
2.6.1. Relationship to MIB-II ................................. 7
2.6.1.1. Relationship to the 'system' group ................... 7
2.6.1.2. Relationship to the 'interfaces' group ............... 8
2.6.2. Relationship to the 802.3 Repeater MIB ................. 8
Flick Standards Track [Page 1]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
2.7. Mapping of IEEE 802.12 Managed Objects ................... 9
3. Definitions ................................................ 12
4. Acknowledgements ........................................... 53
5. References ................................................. 53
6. Security Considerations .................................... 54
7. Author's Address ........................................... 55
8. Full Copyright Statement ................................... 56
1. The SNMP Network Management Framework
The SNMP Network Management Framework consists of several components.
For the purpose of this specification, the applicable components of
the Framework are the SMI and related documents [2, 3, 4], which
define the mechanisms used for describing and naming objects for the
purpose of management.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
1.1. Object Definitions
Managed objects are accessed via a virtual information store, termed
the Management Information Base (MIB). Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1) [1]
defined in the SMI [2]. In particular, each object type is named by
an OBJECT IDENTIFIER, an administratively assigned name. The object
type together with an object instance serves to uniquely identify a
specific instantiation of the object. For human convenience, we
often use a textual string, termed the descriptor, to refer to the
object type.
2. Overview
Instances of these object types represent attributes of an IEEE
802.12 repeater, as defined by Section 12, "RMAC Protocol" in IEEE
Standard 802.12-1995 [6].
The definitions presented here are based on Section 13, "Layer
management functions and services", and Annex C, "GDMO Specifications
for Demand Priority Managed Objects" of IEEE Standard 802.12-1995
[6].
Implementors of these MIB objects should note that the IEEE document
explicitly describes (in the form of Pascal pseudocode) when, where,
and how various repeater attributes are measured. The IEEE document
also describes the effects of repeater actions that may be invoked by
manipulating instances of the MIB objects defined here.
Flick Standards Track [Page 2]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
The counters in this document are defined to be the same as those
counters in IEEE Standard 802.12-1995, with the intention that the
same instrumentation can be used to implement both the IEEE and IETF
management standards.
2.1. Repeater Management Model
The model used in the design of this MIB allows for a managed system
to contain one or more managed 802.12 repeaters, and one or more
managed 802.12 repeater ports.
A repeater port may be thought of as a source of traffic into a
repeater in the system. The vgRptrBasicPortTable contains entries
for each physical repeater port in the managed system. An
implementor may choose to separate these ports into "groups". For
example, a group may be used to represent a field-replaceable unit,
so that the port numbering may match the numbering in the hardware
implementation. Note that this group mapping is recommended but
optional. An implementor may choose to put all of the system's ports
into a single group, or to divide the ports into groups that do not
match physical divisions. Each group within the system is uniquely
identified by a group number. Each port within a system is uniquely
identified by a combination of group number and port number. The
method of numbering groups and ports is implementation-specific.
Both groups and ports may be sparsely numbered.
In addition to the externally visible ports, some implementations may
have internal ports that are not obvious to the end-user but are
nevertheless sources of traffic into the repeater system. Examples
include internal management ports, through which an agent
communicates, and ports connecting to a backplane internal to the
implementation. It is the decision of the implementor to select the
appropriate group(s) in which to place internal ports.
Managed repeaters in the system are represented by entries in the
vgRptrInfoTable. There may be multiple repeaters in the managed
system. They are uniquely identified by a repeater number. The
method of numbering repeaters is implementation-specific. Each port
will either be associated with one of the repeaters, or isolated (a
so-called "trivial" repeater). The set of ports associated with a
single repeater will be in the same contention domain, and will be
participating in the same instance of the Demand Priority Access
Method protocol. The mapping of ports to repeaters may be static or
dynamic. A column in the vgRptrBasicPortTable,
vgRptrPortRptrInfoIndex, indicates the repeater that the port is
currently associated with. The method for assigning a port to a
repeater is implementation-specific.
Flick Standards Track [Page 3]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
2.2. MAC Addresses
All representations of MAC addresses in this MIB module are in
"canonical" order defined by 802.1a, i.e., as if it were transmitted
least significant bit first. This is true even if the repeater is
operating in token ring framing mode, which requires MAC addresses to
be transmitted most significant bit first.
2.3. Master Mode and Slave Mode
In an IEEE 802.12 network, "master" devices act as network
controllers to decide when to grant requesting end-nodes permission
to transmit. These master devices may be repeaters, or other active
controller devices such as switches.
Devices which do not act as network controllers, such as end-nodes or
passive switches, are considered to be operating in "slave" mode.
An 802.12 repeater always acts in "master" mode on its local ports,
which may connect to end nodes, switch or other device ports acting
in "slave" mode, or lower-level repeaters in a cascade. It acts in
"slave" mode on cascade ports, which may connect to an upper-level
repeater in a cascade, or to switch or other device ports operating
in "master" mode.
2.4. IEEE 802.12 Training Frames
Training frames are special MAC frames that are used only during link
initialization. Training frames are initially constructed by the
device at the "lower" end of a link, which is the slave mode device
for the link. The training frame format is as follows:
+----+----+------------+--------------+----------+-----+
| DA | SA | Req Config | Allow Config | Data | FCS |
+----+----+------------+--------------+----------+-----+
DA = destination address (six octets)
SA = source address (six octets)
Req Config = requested configuration (2 octets)
Allow Config = allowed configuration (2 octets)
Data = data (594 to 675 octets)
FCS = frame check sequence (4 octets)
Training frames are always sent with a null destination address. To
pass training, an end node must use its source address in the source
address field of the training frame. A repeater may use a non-null
source address if it has one, or it may use a null source address.
Flick Standards Track [Page 4]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
The requested configuration field allows the slave mode device to
inform the master mode device about itself and to request
configuration options. The training response frame from the master
mode device contains the slave mode device's requested configuration
from the training request frame. The currently defined format of the
requested configuration field as defined in the IEEE Standard
802.12-1995 standard is shown below. Please refer to the most
current version of the IEEE document for a more up to date
description of this field. In particular, the reserved bits may be
used in later versions of the standard.
First Octet: Second Octet:
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|v|v|v|r|r|r|r|r| |r|r|r|F|F|P|P|R|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
vvv: The version of the 802.12 training protocol with which
the training initiator is compliant. The current version
is 100. Note that because of the different bit ordering
used in IEEE and IETF documents, this value corresponds
to version 1.
r: Reserved bits (set to zero)
FF: 00 = frameType88023
01 = frameType88025
10 = reserved
11 = frameTypeEither
PP: 00 = singleAddressMode
01 = promiscuousMode
10 = reserved
11 = reserved
R: 0 = the training initiator is an end node
1 = the training initiator is a repeater
The allowed configuration field allows the master mode device to
respond with the allowed configuration. The slave mode device sets
the contents of this field to all zero bits. The master mode device
sets the allowed configuration field as follows:
First Octet: Second Octet:
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|v|v|v|D|C|N|r|r| |r|r|r|F|F|P|P|R|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
Flick Standards Track [Page 5]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
vvv: The version of the 802.12 training protocol with which
the training responder is compliant. The current version
is 100. Note that because of the different bit ordering
used in IEEE and IETF documents, this value corresponds
to version 1.
D: 0 = No duplicate address has been detected.
1 = Duplicate address has been detected.
C: 0 = The requested configuration is compatible with the
network and the attached port.
1 = The requested configuration is not compatible with
the network and/or the attached port. In this case,
the FF, PP, and R bits indicate a configuration that
would be allowed.
N: 0 = Access will be allowed, providing the configuration
is compatible (C = 0).
1 = Access is not granted because of security
restrictions.
r: Reserved bits (set to zero).
FF: 00 = frameType88023 will be used.
01 = frameType88025 will be used.
10 = reserved
11 = reserved
PP: 00 = singleAddressMode
01 = promiscuousMode
10 = reserved
11 = reserved
R: 0 = Requested access as an end node is allowed.
1 = Requested access as a repeater is allowed.
Again, note that the most recent version of the IEEE 802.12 standard
should be consulted for the most up to date definition of the
requested configuration and allowed configuration fields.
The data field contains between 594 and 675 octets and is filled in
by the training initiator. The first 55 octets may be used for
vendor specific protocol information. The remaining octets are all
zeros. The length of the training frame combined with the
requirement that 24 consecutive training frames be exchanged without
error to complete training ensures that marginal links will not
complete training.
2.5. Structure of the MIB
Objects in this MIB are arranged into OID subtrees, each of which
contains a set of related objects within a broad functional category.
These subtrees are intended for organizational convenience ONLY, and
have no relation to the conformance groups defined later in the
document.
Flick Standards Track [Page 6]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
2.5.1. Basic Definitions
The basic definitions include objects for managing the basic status
and control parameters for each repeater within the managed system,
for the port groups within the managed system, and for the individual
ports themselves.
2.5.2. Monitor Definitions
The monitor definitions include monitoring statistics for each
repeater within the system and for individual ports.
2.5.3. Address Tracking Definitions
This collection includes objects for tracking the MAC addresses of
the DTEs attached to the ports within the system.
Note that this MIB also includes by reference a collection of objects
from the 802.3 Repeater MIB which may be used for mapping the
topology of a network. These definitions are based on a technology
which has been patented by Hewlett-Packard Company (HP). HP has
granted rights to this technology to implementors of this MIB. See
[8] and [9] for details.
2.6. Relationship to other MIBs
2.6.1. Relationship to MIB-II
It is assumed that a repeater implementing this MIB will also
implement (at least) the 'system' group defined in MIB-II [5].
2.6.1.1. Relationship to the 'system' group
In MIB-II, the 'system' group is defined as being mandatory for all
systems such that each managed entity contains one instance of each
object in the 'system' group. Thus, those objects apply to the
entity even if the entity's sole functionality is management of
repeaters.
Note that all of the managed repeaters (i.e. entries in the
vgRptrInfoTable) will normally exist within a single naming scope.
Therefore, there will normally only be a single instance of each of
the objects in the system group for the entire managed repeater
system regardless of how many managed repeaters there are in the
system.
Flick Standards Track [Page 7]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
2.6.1.2. Relationship to the 'interfaces' group
In MIB-II, the 'interfaces' group is defined as being mandatory for
all systems and contains information on an entity's interfaces, where
each interface is thought of as being attached to a 'subnetwork'.
(Note that this term is not to be confused with 'subnet' which refers
to an addressing partitioning scheme used in the Internet suite of
protocols.)
This Repeater MIB uses the notion of ports on a repeater. The
concept of a MIB-II interface has NO specific relationship to a
repeater's port. Therefore, the 'interfaces' group applies only to
the one (or more) network interfaces on which the entity managing the
repeater sends and receives management protocol operations, and does
not apply to the repeater's ports.
This is consistent with the physical-layer nature of a repeater. An
802.12 repeater has an RMAC implementation, which acts as the
repeater end of the Demand Priority Access Method, but does not
contain a DTE MAC implementation, and does not pass packets up to
higher-level protocol entities for processing.
(When a network management entity is observing a repeater, it may
appear as though the repeater is passing packets to a higher-level
protocol entity. However, this is only a means of implementing
management, and this passing of management information is not part of
the repeater functionality.)
2.6.2. Relationship to the 802.3 Repeater MIB
An IEEE 802.12 repeater can be configured to operate in either
ethernet or token ring framing mode. This only affects the frame
format and address bit order of the frames on the wire. An 802.12
network does not use the media access protocol for either ethernet or
token ring. Instead, IEEE 802.12 defines its own media access
protocol, the Demand Priority Access Method (DPAM).
There is an existing standards-track MIB module for instrumenting
IEEE 802.3 repeaters [7]. That MIB module is designed to instrument
the operation of the repeater in a network implementing the 802.3
media access protocol. Therefore, much of that MIB does not apply to
802.12 repeaters.
However, the 802.3 Repeater MIB also contains a collection of objects
that may be used to map the topology of a network. These objects are
contained in a separable OBJECT-GROUP, are not 802.3-specific, and
are considered useful for 802.12 repeaters. In addition, the layer
Flick Standards Track [Page 8]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
management clause of the IEEE 802.12 specification includes similar
functionality. Therefore, vendors of agents for 802.12 repeaters are
encouraged to implement the snmpRptrGrpRptrAddrSearch OBJECT-GROUP
defined in the 802.3 Repeater MIB.
2.7. Mapping of IEEE 802.12 Managed Objects
IEEE 802.12 Managed Object Corresponding SNMP Object
oRepeater
.aCurrentFramingType vgRptrInfoCurrentFramingType
.aDesiredFramingType vgRptrInfoDesiredFramingType
.aFramingCapability vgRptrInfoFramingCapability
.aMACAddress vgRptrInfoMACAddress
.aRepeaterHealthState vgRptrInfoOperStatus
.aRepeaterID vgRptrInfoIndex
.aRepeaterSearchAddress SNMP-REPEATER-MIB -
rptrAddrSearchAddress
.aRepeaterSearchGroup SNMP-REPEATER-MIB -
rptrAddrSearchGroup
.aRepeaterSearchPort SNMP-REPEATER-MIB -
rptrAddrSearchPort
.aRepeaterSearchState SNMP-REPEATER-MIB -
rptrAddrSearchState
.aRMACVersion vgRptrInfoTrainingVersion
.acRepeaterSearchAddress SNMP-REPEATER-MIB -
rptrAddrSearchAddress
.acResetRepeater vgRptrInfoReset
.nRepeaterHealth vgRptrHealth
.nRepeaterReset vgRptrResetEvent
oGroup
.aGroupCablesBundled vgRptrGroupCablesBundled
.aGroupID vgRptrGroupIndex
.aGroupPortCapacity vgRptrGroupPortCapacity
oPort
.aAllowableTrainingType vgRptrPortAllowedTrainType
.aBroadcastFramesReceived vgRptrPortBroadcastFrames
.aCentralMgmtDetectedDupAddr vgRptrMgrDetectedDupAddress
.aDataErrorFramesReceived vgRptrPortDataErrorFrames
.aHighPriorityFramesReceived vgRptrPortHighPriorityFrames
.aHighPriorityOctetsReceived vgRptrPortHCHighPriorityOctets, or
vgRptrPortHighPriorityOctets and
vgRptrPortHighPriOctetRollovers
.aIPMFramesReceived vgRptrPortIPMFrames
.aLastTrainedAddress vgRptrAddrLastTrainedAddress
.aLastTrainingConfig vgRptrPortLastTrainConfig
Flick Standards Track [Page 9]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
.aLocalRptrDetectedDupAddr vgRptrRptrDetectedDupAddress
.aMulticastFramesReceived vgRptrPortMulticastFrames
.aNormalPriorityFramesReceived vgRptrPortNormPriorityFrames
.aNormalPriorityOctetsReceived vgRptrPortHCNormPriorityOctets, or
vgRptrPortNormPriorityOctets and
vgRptrPortNormPriOctetRollovers
.aNullAddressedFramesReceived vgRptrPortNullAddressedFrames
.aOctetsInUnreadableFramesRcvd vgRptrPortHCUnreadableOctets, or
vgRptrPortUnreadableOctets and
vgRptrPortUnreadOctetRollovers
.aOversizeFramesReceived vgRptrPortOversizeFrames
.aPortAdministrativeState vgRptrPortAdminStatus
.aPortID vgRptrPortIndex
.aPortStatus vgRptrPortOperStatus
.aPortType vgRptrPortType
.aPriorityEnable vgRptrPortPriorityEnable
.aPriorityPromotions vgRptrPortPriorityPromotions
.aReadableFramesReceived vgRptrPortReadableFrames
.aReadableOctetsReceived vgRptrPortHCReadableOctets, or
vgRptrPortReadableOctets and
vgRptrPortReadOctetRollovers
.aSupportedCascadeMode vgRptrPortSupportedCascadeMode
.aSupportedPromiscMode vgRptrPortSupportedPromiscMode
.aTrainedAddressChanges vgRptrAddrTrainedAddressChanges
.aTrainingResult vgRptrPortTrainingResult
.aTransitionsIntoTraining vgRptrPortTransitionToTrainings
.acPortAdministrativeControl vgRptrPortAdminStatus
The following IEEE 802.12 managed objects have not been included in
the 802.12 Repeater MIB for the indicated reasons.
IEEE 802.12 Managed Object Disposition
oRepeater
.aGroupMap Can be determined by GetNext sweep
of vgRptrBasicGroupTable
.aRepeaterGroupCapacity Meaning is unclear in many
repeater implementations. For
example, some cards may have
daughter cards which make group
capacity change depending on the
cards installed. Meaning is also
unclear in a stackable
implementation. Also, since
groups are not required to be
numbered from 1..capacity, but may
be computed algorithmically or
Flick Standards Track [Page 10]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
related to Entity MIB indices,
this object was not considered
useful.
.aRepeaterHealthData Since the data is implementation
specific and non-interoperable,
it was not considered useful.
.aRepeaterHealthText Implementation experience with
similar object in 802.3 Rptr MIB
indicated it was not useful.
.acExecuteNonDisruptiveSelfTest Implementation experience with
similar object in 802.3 Rptr MIB
indicated it was not useful.
.nGroupMapChange Since aGroupMap was not included,
a notification of a change in that
object was not needed.
oGroup
.aPortMap Can be determined by GetNext sweep
of vgRptrBasicPortTable
.nPortMapChange Since aPortMap was not included,
a notification of a change in that
object was not needed.
oPort
.aMediaType This object is a function of the
Physical Media Dependent (PMD)
layer, which is defined
differently for each type of
network. For an 802.3 network,
.aMediaType corresponds to the PMD
definitions in the 802.3 MAU MIB.
For management of an 802.12
network, mapping of this object is
deferred to future work on an
802.12 PMD MIB which will include
both repeater and interface PMD
information and redundant link
support.
Flick Standards Track [Page 11]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
3. Definitions
DOT12-RPTR-MIB DEFINITIONS ::= BEGIN
IMPORTS
mib-2, Integer32, Counter32, Counter64,
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE
FROM SNMPv2-SMI
MacAddress, TruthValue, TimeStamp
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF;
vgRptrMIB MODULE-IDENTITY
LAST-UPDATED "9705192256Z" -- May 19, 1997
ORGANIZATION "IETF 100VG-AnyLAN Working Group"
CONTACT-INFO
"WG E-mail:
[email protected]
Chair: Jeff Johnson
Postal: RedBack Networks
2570 North First Street, Suite 410
San Jose, CA 95131
Tel: +1 408 571 2699
Fax: +1 408 571 2698
E-mail:
[email protected]
Editor: John Flick
Postal: Hewlett Packard Company
8000 Foothills Blvd. M/S 5556
Roseville, CA 95747-5556
Tel: +1 916 785 4018
Fax: +1 916 785 3583
E-mail:
[email protected]"
DESCRIPTION
"This MIB module describes objects for managing
IEEE 802.12 repeaters."
::= { mib-2 53 }
vgRptrObjects OBJECT IDENTIFIER ::= { vgRptrMIB 1 }
vgRptrBasic OBJECT IDENTIFIER ::= { vgRptrObjects 1 }
vgRptrBasicRptr OBJECT IDENTIFIER ::= { vgRptrBasic 1 }
vgRptrInfoTable OBJECT-TYPE
SYNTAX SEQUENCE OF VgRptrInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Flick Standards Track [Page 12]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
"A table of information about each 802.12 repeater
in the managed system."
::= { vgRptrBasicRptr 1 }
vgRptrInfoEntry OBJECT-TYPE
SYNTAX VgRptrInfoEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table, containing information
about a single repeater."
INDEX { vgRptrInfoIndex }
::= { vgRptrInfoTable 1 }
VgRptrInfoEntry ::=
SEQUENCE {
vgRptrInfoIndex Integer32,
vgRptrInfoMACAddress MacAddress,
vgRptrInfoCurrentFramingType INTEGER,
vgRptrInfoDesiredFramingType INTEGER,
vgRptrInfoFramingCapability INTEGER,
vgRptrInfoTrainingVersion INTEGER,
vgRptrInfoOperStatus INTEGER,
vgRptrInfoReset INTEGER,
vgRptrInfoLastChange TimeStamp
}
vgRptrInfoIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique identifier for the repeater for which
this entry contains information. The numbering
scheme for repeaters is implementation specific."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aRepeaterID."
::= { vgRptrInfoEntry 1 }
vgRptrInfoMACAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The MAC address used by the repeater when it
initiates training on the uplink port. Repeaters
are allowed to train with an assigned MAC address
Flick Standards Track [Page 13]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
or a null (all zeroes) MAC address."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aMACAddress."
::= { vgRptrInfoEntry 2 }
vgRptrInfoCurrentFramingType OBJECT-TYPE
SYNTAX INTEGER {
frameType88023(1),
frameType88025(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of framing (802.3 or 802.5) currently
in use by the repeater."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aCurrentFramingType."
::= { vgRptrInfoEntry 3 }
vgRptrInfoDesiredFramingType OBJECT-TYPE
SYNTAX INTEGER {
frameType88023(1),
frameType88025(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of framing which will be used by the
repeater after the next time it is reset.
The value of this object should be preserved
across repeater resets and power failures."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aDesiredFramingType."
::= { vgRptrInfoEntry 4 }
vgRptrInfoFramingCapability OBJECT-TYPE
SYNTAX INTEGER {
frameType88023(1),
frameType88025(2),
frameTypeEither(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Flick Standards Track [Page 14]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
"The type of framing this repeater is capable of
supporting."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aFramingCapability."
::= { vgRptrInfoEntry 5 }
vgRptrInfoTrainingVersion OBJECT-TYPE
SYNTAX INTEGER (0..7)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The highest version bits (vvv bits) supported by
the repeater during training."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aRMACVersion."
::= { vgRptrInfoEntry 6 }
vgRptrInfoOperStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
ok(2),
generalFailure(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vgRptrInfoOperStatus object indicates the
operational state of the repeater."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.1,
aRepeaterHealthState."
::= { vgRptrInfoEntry 7 }
vgRptrInfoReset OBJECT-TYPE
SYNTAX INTEGER {
noReset(1),
reset(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to reset(2) causes the
repeater to transition to its initial state as
specified in clause 12 [IEEE Std 802.12].
Flick Standards Track [Page 15]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
Setting this object to noReset(1) has no effect.
The agent will always return the value noReset(1)
when this object is read.
After receiving a request to set this variable to
reset(2), the agent is allowed to delay the reset
for a short period. For example, the implementor
may choose to delay the reset long enough to
allow the SNMP response to be transmitted. In
any event, the SNMP response must be transmitted.
This action does not reset the management
counters defined in this document nor does it
affect the vgRptrPortAdminStatus parameters.
Included in this action is the execution of a
disruptive Self-Test with the following
characteristics:
1) The nature of the tests is not specified.
2) The test resets the repeater but without
affecting configurable management
information about the repeater.
3) Packets received during the test may or
may not be transferred.
4) The test does not interfere with
management functions.
After performing this self-test, the agent will
update the repeater health information (including
vgRptrInfoOperStatus), and send a
vgRptrResetEvent."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.2.2,
acResetRepeater."
::= { vgRptrInfoEntry 8 }
vgRptrInfoLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when any of the following
conditions occurred:
1) agent cold- or warm-started;
2) this instance of repeater was created
(such as when a device or module was
added to the system);
Flick Standards Track [Page 16]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
3) a change in the value of
vgRptrInfoOperStatus;
4) ports were added or removed as members of
the repeater; or
5) any of the counters associated with this
repeater had a discontinuity."
::= { vgRptrInfoEntry 9 }
vgRptrBasicGroup OBJECT IDENTIFIER ::= { vgRptrBasic 2 }
vgRptrBasicGroupTable OBJECT-TYPE
SYNTAX SEQUENCE OF VgRptrBasicGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing information about groups of
ports."
::= { vgRptrBasicGroup 1 }
vgRptrBasicGroupEntry OBJECT-TYPE
SYNTAX VgRptrBasicGroupEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vgRptrBasicGroupTable, containing
information about a single group of ports."
INDEX { vgRptrGroupIndex }
::= { vgRptrBasicGroupTable 1 }
VgRptrBasicGroupEntry ::=
SEQUENCE {
vgRptrGroupIndex Integer32,
vgRptrGroupObjectID OBJECT IDENTIFIER,
vgRptrGroupOperStatus INTEGER,
vgRptrGroupPortCapacity Integer32,
vgRptrGroupCablesBundled INTEGER
}
vgRptrGroupIndex OBJECT-TYPE
SYNTAX Integer32 (1..2146483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the group within the
system for which this entry contains information.
The numbering scheme for groups is implementation
specific."
REFERENCE
Flick Standards Track [Page 17]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
"IEEE Standard 802.12-1995, 13.2.4.4.1,
aGroupID."
::= { vgRptrBasicGroupEntry 1 }
vgRptrGroupObjectID OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor's authoritative identification of the
group. This value may be allocated within the
SMI enterprises subtree (1.3.6.1.4.1) and
provides a straight-forward and unambiguous means
for determining what kind of group is being
managed.
For example, this object could take the value
1.3.6.1.4.1.4242.1.2.14 if vendor 'Flintstones,
Inc.' was assigned the subtree 1.3.6.1.4.1.4242,
and had assigned the identifier
1.3.6.1.4.1.4242.1.2.14 to its 'Wilma Flintstone
6-Port Plug-in Module.'"
::= { vgRptrBasicGroupEntry 2 }
vgRptrGroupOperStatus OBJECT-TYPE
SYNTAX INTEGER {
other(1),
operational(2),
malfunctioning(3),
notPresent(4),
underTest(5),
resetInProgress(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An object that indicates the operational status
of the group.
A status of notPresent(4) indicates that the
group is temporarily or permanently physically
and/or logically not a part of the system. It
is an implementation-specific matter as to
whether the agent effectively removes notPresent
entries from the table.
A status of operational(2) indicates that the
group is functioning, and a status of
Flick Standards Track [Page 18]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
malfunctioning(3) indicates that the group is
malfunctioning in some way."
::= { vgRptrBasicGroupEntry 3 }
vgRptrGroupPortCapacity OBJECT-TYPE
SYNTAX Integer32 (1..2146483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vgRptrGroupPortCapacity is the number of
ports that can be contained within the group.
Valid range is 1-2147483647. Within each group,
the ports are uniquely numbered in the range from
1 to vgRptrGroupPortCapacity.
Some ports may not be present in the system, in
which case the actual number of ports present will
be less than the value of vgRptrGroupPortCapacity.
The number of ports present is never greater than
the value of vgRptrGroupPortCapacity.
Note: In practice, this will generally be the
number of ports on a module, card, or board, and
the port numbers will correspond to numbers marked
on the physical embodiment."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.4.1,
aGroupPortCapacity."
::= { vgRptrBasicGroupEntry 4 }
vgRptrGroupCablesBundled OBJECT-TYPE
SYNTAX INTEGER {
someCablesBundled(1),
noCablesBundled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used to indicate whether there are
any four-pair UTP links connected to this group
that are contained in a cable bundle with multiple
four-pair groups (e.g. a 25-pair bundle). Bundled
cable may only be used for repeater-to-end node
links where the end node is not in promiscuous
mode.
When a broadcast or multicast packet is received
from a port on this group that is not a
Flick Standards Track [Page 19]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
promiscuous or cascaded port, the packet will be
buffered completely before being repeated if
this object is set to 'someCablesBundled(1)'.
When this object is equal to 'noCablesBundled(2)',
all packets received from ports on this group will
be repeated as the frame is being received.
Note that the value 'someCablesBundled(1)' will
work in the vast majority of all installations,
regardless of whether or not any cables are
physically in a bundle, since packets received
from promiscuous and cascaded ports automatically
avoid the store and forward. The main situation
in which 'noCablesBundled(2)' is beneficial is
when there is a large amount of multicast traffic
and the cables are not in a bundle.
The value of this object should be preserved
across repeater resets and power failures."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.4.1,
aGroupCablesBundled."
::= { vgRptrBasicGroupEntry 5 }
vgRptrBasicPort OBJECT IDENTIFIER ::= { vgRptrBasic 3 }
vgRptrBasicPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF VgRptrBasicPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table containing configuration and status
information about 802.12 repeater ports in the
system. The number of entries is independent of
the number of repeaters in the managed system."
::= { vgRptrBasicPort 1 }
vgRptrBasicPortEntry OBJECT-TYPE
SYNTAX VgRptrBasicPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vgRptrBasicPortTable, containing
information about a single port."
INDEX { vgRptrGroupIndex, vgRptrPortIndex }
::= { vgRptrBasicPortTable 1 }
VgRptrBasicPortEntry ::=
Flick Standards Track [Page 20]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
SEQUENCE {
vgRptrPortIndex Integer32,
vgRptrPortType INTEGER,
vgRptrPortAdminStatus INTEGER,
vgRptrPortOperStatus INTEGER,
vgRptrPortSupportedPromiscMode INTEGER,
vgRptrPortSupportedCascadeMode INTEGER,
vgRptrPortAllowedTrainType INTEGER,
vgRptrPortLastTrainConfig OCTET STRING,
vgRptrPortTrainingResult OCTET STRING,
vgRptrPortPriorityEnable TruthValue,
vgRptrPortRptrInfoIndex Integer32
}
vgRptrPortIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies the port within the group
for which this entry contains information. This
identifies the port independently from the
repeater it may be attached to. The numbering
scheme for ports is implementation specific;
however, this value can never be greater than
vgRptrGroupPortCapacity for the associated group."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aPortID."
::= { vgRptrBasicPortEntry 1 }
vgRptrPortType OBJECT-TYPE
SYNTAX INTEGER {
cascadeExternal(1),
cascadeInternal(2),
localExternal(3),
localInternal(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Describes the type of port. One of the
following:
cascadeExternal - Port is an uplink with
physical connections which
are externally visible
cascadeInternal - Port is an uplink with
Flick Standards Track [Page 21]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
physical connections which
are not externally visible,
such as a connection to an
internal backplane in a
chassis
localExternal - Port is a downlink or local
port with externally
visible connections
localInternal - Port is a downlink or local
port with connections which
are not externally visible,
such as a connection to an
internal agent
'internal' is used to identify ports which place
traffic into the repeater, but do not have any
external connections. Note that both DTE and
cascaded repeater downlinks are considered
'local' ports."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aPortType."
::= { vgRptrBasicPortEntry 2 }
vgRptrPortAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
disabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Port enable/disable function. Enabling a
disabled port will cause training to be
initiated by the training initiator (the slave
mode device) on the link. Setting this object to
disabled(2) disables the port.
A disabled port neither transmits nor receives.
Once disabled, a port must be explicitly enabled
to restore operation. A port which is disabled
when power is lost or when a reset is exerted
shall remain disabled when normal operation
resumes.
The value of this object should be preserved
across repeater resets and power failures."
REFERENCE
Flick Standards Track [Page 22]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aPortAdministrativeState."
::= { vgRptrBasicPortEntry 3 }
vgRptrPortOperStatus OBJECT-TYPE
SYNTAX INTEGER {
active(1),
inactive(2),
training(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current status for the port as specified by the
PORT_META_STATE in the port process module of
clause 12 [IEEE Std 802.12].
During initialization or any link warning
conditions, vgRptrPortStatus will be
'inactive(2)'.
When Training_Up is received by the repeater on a
local port (or when Training_Down is received on
a cascade port), vgRptrPortStatus will change to
'training(3)' and vgRptrTrainingResult can be
monitored to see the detailed status regarding
training.
When 24 consecutive good FCS packets are exchanged
and the configuration bits are OK,
vgRptrPortStatus will change to 'active(1)'.
A disabled port shall have a port status of
'inactive(2)'."
REFERENCE
"IEEE Standard 802.12, 13.2.4.5.1,
aPortStatus."
::= { vgRptrBasicPortEntry 4 }
vgRptrPortSupportedPromiscMode OBJECT-TYPE
SYNTAX INTEGER {
singleModeOnly(1),
singleOrPromiscMode(2),
promiscModeOnly(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Flick Standards Track [Page 23]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
"This object describes whether the port hardware
is capable of supporting promiscuous mode, single
address mode (i.e., repeater filters unicasts not
addressed to the end station attached to this
port), or both. A port for which vgRptrPortType
is equal to 'cascadeInternal' or 'cascadeExternal'
will always have a value of 'promiscModeOnly' for
this object."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aSupportedPromiscMode."
::= { vgRptrBasicPortEntry 5 }
vgRptrPortSupportedCascadeMode OBJECT-TYPE
SYNTAX INTEGER {
endNodesOnly(1),
endNodesOrRepeaters(2),
cascadePort(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object describes whether the port hardware
is capable of supporting cascaded repeaters, end
nodes, or both. A port for which vgRptrPortType
is equal to 'cascadeInternal' or
'cascadeExternal' will always have a value of
'cascadePort' for this object."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aSupportedCascadeMode."
::= { vgRptrBasicPortEntry 6 }
vgRptrPortAllowedTrainType OBJECT-TYPE
SYNTAX INTEGER {
allowEndNodesOnly(1),
allowPromiscuousEndNodes(2),
allowEndNodesOrRepeaters(3),
allowAnything(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This security object is set by the network
manager to configure what type of device is
permitted to connect to the port. One of the
following values:
Flick Standards Track [Page 24]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
allowEndNodesOnly - only non-
promiscuous end
nodes permitted.
allowPromiscuousEndNodes - promiscuous or
non-promiscuous
end nodes
permitted
allowEndNodesOrRepeaters - repeaters or non-
promiscuous end
nodes permitted
allowAnything - repeaters,
promiscuous or
non-promiscuous
end nodes
permitted
For a port for which vgRptrPortType is equal to
'cascadeInternal' or 'cascadeExternal', the
corresponding instance of this object may not be
set to 'allowEndNodesOnly' or
'allowPromiscuousEndNodes'.
The agent must reject a SET of this object if the
value includes no capabilities that are
supported by this port's hardware, as defined by
the values of the corresponding instances of
vgRptrPortSupportedPromiscMode and
vgRptrPortSupportedCascadeMode.
Note that vgRptrPortSupportPromiscMode and
vgRptrPortSupportedCascadeMode represent what the
port hardware is capable of supporting.
vgRptrPortAllowedTrainType is used for setting an
administrative policy for a port. The actual set
of training configurations that will be allowed
to succeed on a port is the intersection of what
the hardware will support and what is
administratively allowed. The above requirement
on what values may be set to this object says that
the intersection of what is supported and what is
allowed must be non-empty. In other words, it
must not result in a situation in which nothing
would be allowed to train on that port. However,
a value can be set to this object as long as the
combination of this object and what is supported
by the hardware would still leave at least one
configuration that could successfully train on the
port.
Flick Standards Track [Page 25]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
The value of this object should be preserved
across repeater resets and power failures."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aAllowableTrainingType."
::= { vgRptrBasicPortEntry 7 }
vgRptrPortLastTrainConfig OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a 16 bit field. For local ports,
this object contains the requested configuration
field from the most recent error-free training
request frame sent by the device connected to
the port. For cascade ports, this object contains
the responder's allowed configuration field from
the most recent error-free training response frame
received in response to training initiated by this
repeater. The format of the current version of
this field is described in section 3.2. Please
refer to the most recent version of the IEEE
802.12 standard for the most up-to-date definition
of the format of this object."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aLastTrainingConfig."
::= { vgRptrBasicPortEntry 8 }
vgRptrPortTrainingResult OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This 18 bit field is used to indicate the result
of training. It contains two bits which indicate
if error-free training frames have been received,
and it also contains the 16 bits of the allowed
configuration field from the most recent
error-free training response frame on the port.
First Octet: Second and Third Octets:
7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+-----------------------------+
|0|0|0|0|0|0|V|G| allowed configuration field |
+-+-+-+-+-+-+-+-+-----------------------------+
Flick Standards Track [Page 26]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
V: Valid: set when at least one error-free
training frame has been received.
Indicates the 16 training configuration
bits in vgRptrPortLastTrainConfig and
vgRptrPortTrainingResult contain valid
information. This bit is cleared when
vgRptrPortStatus transitions to the
'inactive' or 'training' state.
G: LinkGood: indicates the link hardware is
OK. Set if 24 consecutive error-free
training packets have been exchanged.
Cleared when a training packet with
errors is received, or when
vgRptrPortStatus transitions to the
'inactive' or 'training' state.
The format of the current version of the allowed
configuration field is described in section 3.2.
Please refer to the most recent version of the
IEEE 802.12 standard for the most up-to-date
definition of the format of this field.
If the port is in training, a management station
can examine this object to see if any training
packets have been passed successfully. If there
have been any good training packets, the Valid
bit will be set and the management station can
examine the allowed configuration field to see if
there is a duplicate address, configuration, or
security problem.
Note that on a repeater local port, this repeater
generates the training response bits, while on
a cascade port, the device at the upper end of
the link originated the training response bits."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aTrainingResult."
::= { vgRptrBasicPortEntry 9 }
vgRptrPortPriorityEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A configuration flag used to determine whether
the repeater will service high priority requests
received on the port as high priority or normal
priority. When 'false', high priority requests
Flick Standards Track [Page 27]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
on this port will be serviced as normal priority.
The setting of this object has no effect on a
cascade port. Also note that the setting of this
object has no effect on a port connected to a
cascaded repeater. In both of these cases, this
setting is treated as always 'true'. The value
'false' only has an effect when the port is a
localInternal or localExternal port connected to
an end node.
The value of this object should be preserved
across repeater resets and power failures."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aPriorityEnable."
::= { vgRptrBasicPortEntry 10 }
vgRptrPortRptrInfoIndex OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the repeater that this
port is currently mapped to. The repeater
identified by a particular value of this object
is the same as that identified by the same value
of vgRptrInfoIndex. A value of zero indicates
that this port is not currently mapped to any
repeater."
::= { vgRptrBasicPortEntry 11 }
vgRptrMonitor OBJECT IDENTIFIER ::= { vgRptrObjects 2 }
vgRptrMonRepeater OBJECT IDENTIFIER ::= { vgRptrMonitor 1 }
vgRptrMonitorTable OBJECT-TYPE
SYNTAX SEQUENCE OF VgRptrMonitorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of performance and error statistics for
each repeater in the system. The instance of the
vgRptrInfoLastChange associated with a repeater
is used to indicate possible discontinuities of
the counters in this table that are associated
with the same repeater."
Flick Standards Track [Page 28]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
::= { vgRptrMonRepeater 1 }
vgRptrMonitorEntry OBJECT-TYPE
SYNTAX VgRptrMonitorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table, containing statistics
for a single repeater."
INDEX { vgRptrInfoIndex }
::= { vgRptrMonitorTable 1 }
VgRptrMonitorEntry ::=
SEQUENCE {
vgRptrMonTotalReadableFrames Counter32,
vgRptrMonTotalReadableOctets Counter32,
vgRptrMonReadableOctetRollovers Counter32,
vgRptrMonHCTotalReadableOctets Counter64,
vgRptrMonTotalErrors Counter32
}
vgRptrMonTotalReadableFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of good frames of valid frame
length that have been received on all ports in
this repeater. If an implementation cannot
obtain a count of frames as seen by the repeater
itself, this counter may be implemented as the
summation of the values of the
vgRptrPortReadableFrames counters for all of the
ports in this repeater.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrInfoLastChange changes."
::= { vgRptrMonitorEntry 1 }
vgRptrMonTotalReadableOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets contained in good
frames that have been received on all ports in
this repeater. If an implementation cannot
Flick Standards Track [Page 29]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
obtain a count of octets as seen by the repeater
itself, this counter may be implemented as the
summation of the values of the
vgRptrPortReadableOctets counters for all of the
ports in this repeater.
Note that this counter can roll over very
quickly. A management station is advised to
also poll the vgRptrReadableOctetRollovers
object, or to use the 64-bit counter defined by
vgRptrMonHCTotalReadableOctets instead of the
two 32-bit counters.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrInfoLastChange changes."
::= { vgRptrMonitorEntry 2 }
vgRptrMonReadableOctetRollovers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of times that the associated
instance of the vgRptrMonTotalReadableOctets
counter has rolled over.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrInfoLastChange changes."
::= { vgRptrMonitorEntry 3 }
vgRptrMonHCTotalReadableOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
Flick Standards Track [Page 30]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
DESCRIPTION
"The total number of octets contained in good
frames that have been received on all ports in
this repeater. If an implementation cannot
obtain a count of octets as seen by the repeater
itself, this counter may be implemented as the
summation of the values of the
vgRptrPortHCReadableOctets counters for all of the
ports in this repeater.
This counter is a 64 bit version of
vgRptrMonTotalReadableOctets. It should be used
by Network Management protocols which support 64
bit counters (e.g. SNMPv2).
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrInfoLastChange changes."
::= { vgRptrMonitorEntry 4 }
vgRptrMonTotalErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of errors which have occurred on
all of the ports in this repeater. If an
implementation cannot obtain a count of these
errors as seen by the repeater itself, this
counter may be implemented as the summation of the
values of the vgRptrPortIPMFrames,
vgRptrPortOversizeFrames, and
vgRptrPortDataErrorFrames counters for all of the
ports in this repeater.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrInfoLastChange changes."
::= { vgRptrMonitorEntry 5 }
vgRptrMonGroup OBJECT IDENTIFIER ::= { vgRptrMonitor 2 }
-- Currently unused
vgRptrMonPort OBJECT IDENTIFIER ::= { vgRptrMonitor 3 }
vgRptrMonPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF VgRptrMonPortEntry
MAX-ACCESS not-accessible
Flick Standards Track [Page 31]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
STATUS current
DESCRIPTION
"A table of performance and error statistics for
the ports. The columnar object
vgRptrPortLastChange is used to indicate possible
discontinuities of counter type columnar objects
in this table."
::= { vgRptrMonPort 1 }
vgRptrMonPortEntry OBJECT-TYPE
SYNTAX VgRptrMonPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the vgRptrMonPortTable, containing
performance and error statistics for a single
port."
INDEX { vgRptrGroupIndex, vgRptrPortIndex }
::= { vgRptrMonPortTable 1 }
VgRptrMonPortEntry ::=
SEQUENCE {
vgRptrPortReadableFrames Counter32,
vgRptrPortReadableOctets Counter32,
vgRptrPortReadOctetRollovers Counter32,
vgRptrPortHCReadableOctets Counter64,
vgRptrPortUnreadableOctets Counter32,
vgRptrPortUnreadOctetRollovers Counter32,
vgRptrPortHCUnreadableOctets Counter64,
vgRptrPortHighPriorityFrames Counter32,
vgRptrPortHighPriorityOctets Counter32,
vgRptrPortHighPriOctetRollovers Counter32,
vgRptrPortHCHighPriorityOctets Counter64,
vgRptrPortNormPriorityFrames Counter32,
vgRptrPortNormPriorityOctets Counter32,
vgRptrPortNormPriOctetRollovers Counter32,
vgRptrPortHCNormPriorityOctets Counter64,
vgRptrPortBroadcastFrames Counter32,
vgRptrPortMulticastFrames Counter32,
vgRptrPortNullAddressedFrames Counter32,
vgRptrPortIPMFrames Counter32,
vgRptrPortOversizeFrames Counter32,
vgRptrPortDataErrorFrames Counter32,
vgRptrPortPriorityPromotions Counter32,
vgRptrPortTransitionToTrainings Counter32,
vgRptrPortLastChange TimeStamp
}
Flick Standards Track [Page 32]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
vgRptrPortReadableFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the number of good frames of
valid frame length that have been received on
this port. This counter is incremented by one
for each frame received on the port which is not
counted by any of the following error counters:
vgRptrPortIPMFrames, vgRptrPortOversizeFrames,
vgRptrPortNullAddressedFrames, or
vgRptrPortDataErrorFrames.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aReadableFramesReceived."
::= { vgRptrMonPortEntry 1 }
vgRptrPortReadableOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in good frames that have been received
on this port. This counter is incremented by
OctetCount for each frame received on this port
which has been determined to be a readable frame
(i.e. each frame counted by
vgRptrPortReadableFrames).
Note that this counter can roll over very
quickly. A management station is advised to
also poll the vgRptrPortReadOctetRollovers
object, or to use the 64-bit counter defined by
vgRptrPortHCReadableOctets instead of the two
32-bit counters.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
Flick Standards Track [Page 33]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aReadableOctetsReceived."
::= { vgRptrMonPortEntry 2 }
vgRptrPortReadOctetRollovers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of times
that the associated instance of the
vgRptrPortReadableOctets counter has rolled over.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aReadableOctetsReceived."
::= { vgRptrMonPortEntry 3 }
vgRptrPortHCReadableOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in good frames that have been received
on this port. This counter is incremented by
OctetCount for each frame received on this port
which has been determined to be a readable frame
(i.e. each frame counted by
vgRptrPortReadableFrames).
This counter is a 64 bit version of
vgRptrPortReadableOctets. It should be used by
Network Management protocols which support 64 bit
counters (e.g. SNMPv2).
Flick Standards Track [Page 34]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aReadableOctetsReceived."
::= { vgRptrMonPortEntry 4 }
vgRptrPortUnreadableOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in invalid frames that have been
received on this port. This counter is
incremented by OctetCount for each frame received
on this port which is counted by
vgRptrPortIPMFrames, vgRptrPortOversizeFrames,
vgRptrPortNullAddressedFrames, or
vgRptrPortDataErrorFrames. This counter can be
combined with vgRptrPortReadableOctets to
calculate network utilization.
Note that this counter can roll over very
quickly. A management station is advised to
also poll the vgRptrPortUnreadOctetRollovers
object, or to use the 64-bit counter defined by
vgRptrPortHCUnreadableOctets instead of the two
32-bit counters.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aOctetsInUnreadableFramesRcvd."
::= { vgRptrMonPortEntry 5 }
vgRptrPortUnreadOctetRollovers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
Flick Standards Track [Page 35]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
STATUS current
DESCRIPTION
"This object is a count of the number of times
that the associated instance of the
vgRptrPortUnreadableOctets counter has rolled
over.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aOctetsInUnreadableFramesRcvd."
::= { vgRptrMonPortEntry 6 }
vgRptrPortHCUnreadableOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in invalid frames that have been
received on this port. This counter is
incremented by OctetCount for each frame received
on this port which is counted by
vgRptrPortIPMFrames, vgRptrPortOversizeFrames,
vgRptrPortNullAddressedFrames, or
vgRptrPortDataErrorFrames. This counter can be
combined with vgRptrPortHCReadableOctets to
calculate network utilization.
This counter is a 64 bit version of
vgRptrPortUnreadableOctets. It should be used
by Network Management protocols which support 64
bit counters (e.g. SNMPv2).
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aOctetsInUnreadableFramesRcvd."
Flick Standards Track [Page 36]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
::= { vgRptrMonPortEntry 7 }
vgRptrPortHighPriorityFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of high priority frames
that have been received on this port. This
counter is incremented by one for each high
priority frame received on this port. This
counter includes both good and bad high priority
frames, as well as high priority training frames.
This counter does not include normal priority
frames which were priority promoted.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aHighPriorityFramesReceived."
::= { vgRptrMonPortEntry 8 }
vgRptrPortHighPriorityOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in high priority frames that have been
received on this port. This counter is
incremented by OctetCount for each frame received
on this port which is counted by
vgRptrPortHighPriorityFrames.
Note that this counter can roll over very
quickly. A management station is advised to
also poll the vgRptrPortHighPriOctetRollovers
object, or to use the 64-bit counter defined by
vgRptrPortHCHighPriorityOctets instead of the two
32-bit counters.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
Flick Standards Track [Page 37]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aHighPriorityOctetsReceived."
::= { vgRptrMonPortEntry 9 }
vgRptrPortHighPriOctetRollovers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of times
that the associated instance of the
vgRptrPortHighPriorityOctets counter has rolled
over.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aHighPriorityOctetsReceived."
::= { vgRptrMonPortEntry 10 }
vgRptrPortHCHighPriorityOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in high priority frames that have been
received on this port. This counter is
incremented by OctetCount for each frame received
on this port which is counted by
vgRptrPortHighPriorityFrames.
This counter is a 64 bit version of
vgRptrPortHighPriorityOctets. It should be used
by Network Management protocols which support
64 bit counters (e.g. SNMPv2).
Flick Standards Track [Page 38]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aHighPriorityOctetsReceived."
::= { vgRptrMonPortEntry 11 }
vgRptrPortNormPriorityFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of normal priority frames
that have been received on this port. This
counter is incremented by one for each normal
priority frame received on this port. This
counter includes both good and bad normal
priority frames, as well as normal priority
training frames and normal priority frames which
were priority promoted.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aNormalPriorityFramesReceived."
::= { vgRptrMonPortEntry 12 }
vgRptrPortNormPriorityOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in normal priority frames that have
been received on this port. This counter is
incremented by OctetCount for each frame received
on this port which is counted by
vgRptrPortNormPriorityFrames.
Note that this counter can roll over very
quickly. A management station is advised to
also poll the vgRptrPortNormPriOctetRollovers
object, or to use the 64-bit counter defined by
vgRptrPortHCNormPriorityOctets instead of the two
32-bit counters.
Flick Standards Track [Page 39]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aNormalPriorityOctetsReceived."
::= { vgRptrMonPortEntry 13 }
vgRptrPortNormPriOctetRollovers OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of times
that the associated instance of the
vgRptrPortNormPriorityOctets counter has rolled
over.
This two-counter mechanism is provided for those
network management protocols that do not support
64-bit counters (e.g. SNMPv1). Note that
retrieval of these two counters in the same PDU
is NOT guaranteed to be atomic.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aNormalPriorityOctetsReceived."
::= { vgRptrMonPortEntry 14 }
vgRptrPortHCNormPriorityOctets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of octets
contained in normal priority frames that have
been received on this port. This counter is
incremented by OctetCount for each frame received
Flick Standards Track [Page 40]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
on this port which is counted by
vgRptrPortNormPriorityFrames.
This counter is a 64 bit version of
vgRptrPortNormPriorityOctets. It should be used
by Network Management protocols which support
64 bit counters (e.g. SNMPv2).
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aNormalPriorityOctetsReceived."
::= { vgRptrMonPortEntry 15 }
vgRptrPortBroadcastFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of broadcast packets that
have been received on this port. This counter is
incremented by one for each readable frame
received on this port whose destination MAC
address is the broadcast address. Frames
counted by this counter are also counted by
vgRptrPortReadableFrames.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aBroadcastFramesReceived."
::= { vgRptrMonPortEntry 16 }
vgRptrPortMulticastFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of multicast packets that
have been received on this port. This counter is
incremented by one for each readable frame
received on this port whose destination MAC
address has the group address bit set, but is not
the broadcast address. Frames counted by this
Flick Standards Track [Page 41]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
counter are also counted by
vgRptrPortReadableFrames, but not by
vgRptrPortBroadcastFrames. Note that when the
value of the instance vgRptrInfoCurrentFramingType
for the repeater that this port is associated
with is equal to 'frameType88025', this count
includes packets addressed to functional
addresses.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aMulticastFramesReceived."
::= { vgRptrMonPortEntry 17 }
vgRptrPortNullAddressedFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of null addressed packets
that have been received on this port. This
counter is incremented by one for each frame
received on this port with a destination MAC
address consisting of all zero bits. Both void
and training frames are included in this
counter.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aNullAddressedFramesReceived."
::= { vgRptrMonPortEntry 18 }
vgRptrPortIPMFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of the number of frames
that have been received on this port with an
invalid packet marker and no PMI errors. A
repeater will write an invalid packet marker to
the end of a frame containing errors as it is
Flick Standards Track [Page 42]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
forwarded through the repeater to the other
ports. This counter is incremented by one for
each frame received on this port which has had an
invalid packet marker added to the end of the
frame.
This counter indicates problems occurring in the
domain of other repeaters, as opposed to problems
with cables or devices directly attached to this
repeater.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aIPMFramesReceived."
::= { vgRptrMonPortEntry 19 }
vgRptrPortOversizeFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of oversize frames
received on this port. This counter is
incremented by one for each frame received on
this port whose OctetCount is larger than the
maximum legal frame size.
The frame size which causes this counter to
increment is dependent on the current value of
vgRptrInfoCurrentFramingType for the repeater that
the port is associated with. When
vgRptrInfoCurrentFramingType is equal to
frameType88023 this counter will increment for
frames that are 1519 octets or larger. When
vgRptrInfoCurrentFramingType is equal to
frameType88025 this counter will increment for
frames that are 4521 octets or larger.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aOversizeFramesReceived."
::= { vgRptrMonPortEntry 20 }
Flick Standards Track [Page 43]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
vgRptrPortDataErrorFrames OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is a count of errored frames
received on this port. This counter is
incremented by one for each frame received on
this port with any of the following errors: bad
FCS (with no IPM), PMI errors (excluding frames
with an IPM error as the only PMI error), or
undersize (with no IPM). Does not include
packets counted by vgRptrPortIPMFrames,
vgRptrPortOversizeFrames, or
vgRptrPortNullAddressedFrames.
This counter indicates problems with cables or
devices directly connected to this repeater, while
vgRptrPortIPMFrames indicates problems occurring
in the domain of other repeaters.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aDataErrorFramesReceived."
::= { vgRptrMonPortEntry 21 }
vgRptrPortPriorityPromotions OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter is incremented by one each time the
priority promotion timer has expired on this port
and a normal priority frame is priority
promoted.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aPriorityPromotions."
::= { vgRptrMonPortEntry 22 }
vgRptrPortTransitionToTrainings OBJECT-TYPE
Flick Standards Track [Page 44]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter is incremented by one each time the
vgRptrPortStatus object for this port transitions
into the 'training' state.
This counter may experience a discontinuity when
the value of the corresponding instance of
vgRptrPortLastChange changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aTransitionsIntoTraining."
::= { vgRptrMonPortEntry 23 }
vgRptrPortLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime when the last of the
following occurred:
1) the agent cold- or warm-started;
2) the row for the port was created
(such as when a device or module was
added to the system); or
3) any condition that would cause one of
the counters for the row to experience
a discontinuity."
::= { vgRptrMonPortEntry 24 }
vgRptrAddrTrack OBJECT IDENTIFIER ::= { vgRptrObjects 3 }
vgRptrAddrTrackRptr
OBJECT IDENTIFIER ::= { vgRptrAddrTrack 1 }
-- Currently unused
vgRptrAddrTrackGroup
OBJECT IDENTIFIER ::= { vgRptrAddrTrack 2 }
-- Currently unused
vgRptrAddrTrackPort
OBJECT IDENTIFIER ::= { vgRptrAddrTrack 3 }
vgRptrAddrTrackTable OBJECT-TYPE
Flick Standards Track [Page 45]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
SYNTAX SEQUENCE OF VgRptrAddrTrackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of address mapping information about the
ports."
::= { vgRptrAddrTrackPort 1 }
vgRptrAddrTrackEntry OBJECT-TYPE
SYNTAX VgRptrAddrTrackEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table, containing address mapping
information about a single port."
INDEX { vgRptrGroupIndex, vgRptrPortIndex }
::= { vgRptrAddrTrackTable 1 }
VgRptrAddrTrackEntry ::=
SEQUENCE {
vgRptrAddrLastTrainedAddress OCTET STRING,
vgRptrAddrTrainedAddrChanges Counter32,
vgRptrRptrDetectedDupAddress TruthValue,
vgRptrMgrDetectedDupAddress TruthValue
}
vgRptrAddrLastTrainedAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the MAC address of the last
station which succeeded in training on this port.
A cascaded repeater may train using the null
address. If no stations have succeeded in
training on this port since the agent began
monitoring the port activity, the agent shall
return a string of length zero."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aLastTrainedAddress."
::= { vgRptrAddrTrackEntry 1 }
vgRptrAddrTrainedAddrChanges OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Flick Standards Track [Page 46]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
DESCRIPTION
"This counter is incremented by one for each time
that the vgRptrAddrLastTrainedAddress object for
this port changes."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aTrainedAddressChanges."
::= { vgRptrAddrTrackEntry 2 }
vgRptrRptrDetectedDupAddress OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is used to indicate that the
repeater detected an error-free training frame on
this port with a non-null source MAC address which
matches the value of vgRptrAddrLastTrainedAddress
of another active port in the same repeater. This
is reset to 'false' when an error-free training
frame is received with a non-null source MAC
address which does not match
vgRptrAddrLastTrainedAddress of another port which
is active in the same repeater.
For the cascade port, this object will be 'true'
if the 'D' bit in the most recently received
error-free training response frame was set,
indicating the device at the other end of the link
believes that this repeater's cascade port is
using a duplicate address. This may be because
the device at the other end of the link detected a
duplicate address itself, or, if the other device
is also a repeater, it could be because
vgRptrMgrDetectedDupAddress was set to 'true' on
the port that this repeater's cascade port is
connected to."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aLocalRptrDetectedDupAddr."
::= { vgRptrAddrTrackEntry 3 }
vgRptrMgrDetectedDupAddress OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object can be set by a management station
Flick Standards Track [Page 47]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
when it detects that there is a duplicate MAC
address. This object is OR'd with
vgRptrRptrDetectedDupAddress to form the value of
the 'D' bit in training response frames on this
port.
The purpose of this object is to provide a means
for network management software to inform an end
station that it is using a duplicate station
address. Setting this object does not affect the
current state of the link; the end station will
not be informed of the duplicate address until it
retrains for some reason. Note that regardless
of its station address, the end station will not
be able to train successfully until the network
management software has set this object back to
'false'. Although this object exists on
cascade ports, it does not perform any function
since this repeater is the initiator of training
on a cascade port."
REFERENCE
"IEEE Standard 802.12-1995, 13.2.4.5.1,
aCentralMgmtDetectedDupAddr."
::= { vgRptrAddrTrackEntry 4 }
vgRptrTraps OBJECT IDENTIFIER ::= { vgRptrMIB 2 }
vgRptrTrapPrefix OBJECT IDENTIFIER ::= { vgRptrTraps 0 }
vgRptrHealth NOTIFICATION-TYPE
OBJECTS { vgRptrInfoOperStatus }
STATUS current
DESCRIPTION
"A vgRptrHealth trap conveys information related
to the operational state of a repeater. This trap
is sent when the value of an instance of
vgRptrInfoOperStatus changes. The vgRptrHealth
trap is not sent as a result of powering up a
repeater.
The vgRptrHealth trap must contain the instance of
the vgRptrInfoOperStatus object associated with
the affected repeater.
The agent must throttle the generation of
consecutive vgRptrHealth traps so that there is at
least a five-second gap between traps of this
type. When traps are throttled, they are dropped,
Flick Standards Track [Page 48]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
not queued for sending at a future time. (Note
that 'generating' a trap means sending to all
configured recipients.)"
REFERENCE
"IEEE 802.12, Layer Management, 13.2.4.2.3,
nRepeaterHealth."
::= { vgRptrTrapPrefix 1 }
vgRptrResetEvent NOTIFICATION-TYPE
OBJECTS { vgRptrInfoOperStatus }
STATUS current
DESCRIPTION
"A vgRptrResetEvent trap conveys information
related to the operational state of a repeater.
This trap is sent on completion of a repeater
reset action. A repeater reset action is defined
as a transition to its initial state as specified
in clause 12 [IEEE Std 802.12] when triggered by
a management command.
The vgRptrResetEvent trap is not sent when the
agent restarts and sends an SNMP coldStart or
warmStart trap.
The vgRptrResetEvent trap must contain the
instance of the vgRptrInfoOperStatus object
associated with the affected repeater.
The agent must throttle the generation of
consecutive vgRptrResetEvent traps so that there
is at least a five-second gap between traps of
this type. When traps are throttled, they are
dropped, not queued for sending at a future time.
(Note that 'generating' a trap means sending to
all configured recipients.)"
REFERENCE
"IEEE 802.12, Layer Management, 13.2.4.2.3,
nRepeaterReset."
::= { vgRptrTrapPrefix 2 }
-- conformance information
vgRptrConformance OBJECT IDENTIFIER ::= { vgRptrMIB 3 }
vgRptrCompliances
OBJECT IDENTIFIER ::= { vgRptrConformance 1 }
vgRptrGroups OBJECT IDENTIFIER ::= { vgRptrConformance 2 }
Flick Standards Track [Page 49]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
-- compliance statements
vgRptrCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for managed 802.12
repeaters."
MODULE -- this module
MANDATORY-GROUPS { vgRptrConfigGroup,
vgRptrStatsGroup,
vgRptrAddrGroup,
vgRptrNotificationsGroup }
GROUP vgRptrStats64Group
DESCRIPTION
"Implementation of this group is recommended
for systems which can support Counter64."
OBJECT vgRptrInfoDesiredFramingType
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required
in a repeater system that does not support
configuration of framing types."
MODULE SNMP-REPEATER-MIB
GROUP snmpRptrGrpRptrAddrSearch
DESCRIPTION
"Implementation of this group is recommended
for systems which have the necessary
instrumentation to search all incoming data
streams for a particular source MAC address."
::= { vgRptrCompliances 1 }
-- units of conformance
vgRptrConfigGroup OBJECT-GROUP
OBJECTS {
vgRptrInfoMACAddress,
vgRptrInfoCurrentFramingType,
vgRptrInfoDesiredFramingType,
vgRptrInfoFramingCapability,
vgRptrInfoTrainingVersion,
vgRptrInfoOperStatus,
vgRptrInfoReset,
vgRptrInfoLastChange,
vgRptrGroupObjectID,
Flick Standards Track [Page 50]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
vgRptrGroupOperStatus,
vgRptrGroupPortCapacity,
vgRptrGroupCablesBundled,
vgRptrPortType,
vgRptrPortAdminStatus,
vgRptrPortOperStatus,
vgRptrPortSupportedPromiscMode,
vgRptrPortSupportedCascadeMode,
vgRptrPortAllowedTrainType,
vgRptrPortLastTrainConfig,
vgRptrPortTrainingResult,
vgRptrPortPriorityEnable,
vgRptrPortRptrInfoIndex
}
STATUS current
DESCRIPTION
"A collection of objects for managing the status
and configuration of IEEE 802.12 repeaters."
::= { vgRptrGroups 1 }
vgRptrStatsGroup OBJECT-GROUP
OBJECTS {
vgRptrMonTotalReadableFrames,
vgRptrMonTotalReadableOctets,
vgRptrMonReadableOctetRollovers,
vgRptrMonTotalErrors,
vgRptrPortReadableFrames,
vgRptrPortReadableOctets,
vgRptrPortReadOctetRollovers,
vgRptrPortUnreadableOctets,
vgRptrPortUnreadOctetRollovers,
vgRptrPortHighPriorityFrames,
vgRptrPortHighPriorityOctets,
vgRptrPortHighPriOctetRollovers,
vgRptrPortNormPriorityFrames,
vgRptrPortNormPriorityOctets,
vgRptrPortNormPriOctetRollovers,
vgRptrPortBroadcastFrames,
vgRptrPortMulticastFrames,
vgRptrPortNullAddressedFrames,
vgRptrPortIPMFrames,
vgRptrPortOversizeFrames,
vgRptrPortDataErrorFrames,
vgRptrPortPriorityPromotions,
vgRptrPortTransitionToTrainings,
vgRptrPortLastChange
}
STATUS current
Flick Standards Track [Page 51]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
DESCRIPTION
"A collection of objects for providing statistics
for IEEE 802.12 repeaters. Systems which support
Counter64 should also implement
vgRptrStats64Group."
::= { vgRptrGroups 2 }
vgRptrStats64Group OBJECT-GROUP
OBJECTS {
vgRptrMonHCTotalReadableOctets,
vgRptrPortHCReadableOctets,
vgRptrPortHCUnreadableOctets,
vgRptrPortHCHighPriorityOctets,
vgRptrPortHCNormPriorityOctets
}
STATUS current
DESCRIPTION
"A collection of objects for providing statistics
for IEEE 802.12 repeaters in a system that
supports Counter64."
::= { vgRptrGroups 3 }
vgRptrAddrGroup OBJECT-GROUP
OBJECTS {
vgRptrAddrLastTrainedAddress,
vgRptrAddrTrainedAddrChanges,
vgRptrRptrDetectedDupAddress,
vgRptrMgrDetectedDupAddress
}
STATUS current
DESCRIPTION
"A collection of objects for tracking addresses
on IEEE 802.12 repeaters."
::= { vgRptrGroups 4 }
vgRptrNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
vgRptrHealth,
vgRptrResetEvent
}
STATUS current
DESCRIPTION
"A collection of notifications used to indicate
802.12 repeater general status changes."
::= { vgRptrGroups 5 }
END
Flick Standards Track [Page 52]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
4. Acknowledgements
This document was produced by the IETF 100VG-AnyLAN Working Group,
whose efforts were greatly advanced by the contributions of the
following people:
Paul Chefurka
Bob Faulk
Jeff Johnson
Karen Kimball
David Lapp
Jason Spofford
Kaj Tesink
This document is based on the work of IEEE 802.12.
5. References
[1] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
International Organization for Standardization. International
Standard 8824 (December, 1987).
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and
S. Waldbusser, "Structure of Management Information for Version 2
of the Simple Network Management Protocol (SNMPv2)", RFC 1902,
January 1996.
[3] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and
S. Waldbusser, "Textual Conventions for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1903, January 1996.
[4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M. and
S. Waldbusser, "Conformance Statements for Version 2 of the
Simple Network Management Protocol (SNMPv2)", RFC 1904, January
1996.
[5] McCloghrie, K. and M. Rose, "Management Information Base for
Network Management of TCP/IP-based internets - MIB-II", STD 17,
RFC 1213, March 1991.
[6] IEEE, "Demand Priority Access Method, Physical Layer and
Repeater Specifications for 100 Mb/s Operation", IEEE Standard
802.12-1995"
Flick Standards Track [Page 53]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
[7] de Graaf, K., D. Romascanu, D. McMaster, and K. McCloghrie,
"Definitions of Managed Objects for IEEE 802.3 Repeater Devices",
RFC 2108, 3Com Corporation, Madge Networks (Israel) Ltd., Cisco
Systems, Inc., February, 1997.
[8] McAnally, G., Gilbert, D. and J. Flick, "Conditional Grant of
Rights to Specific Hewlett-Packard Patents In Conjunction With
the Internet Engineering Task Force's Internet-Standard Network
Management Framework", RFC 1988, August 1996.
[9] Hewlett-Packard Company, US Patents 5,293,635 and 5,421,024.
6. Security Considerations
Certain management information defined in this MIB may be considered
sensitive in some network environments. Therefore, authentication of
received SNMP requests and controlled access to management
information should be employed in such environments. The method for
this authentication is a function of the SNMP Administrative
Framework, and has not been expanded by this MIB.
Several objects in the vgRptrConfigGroup allow write access. Setting
these objects can have a serious effect on the operation of the
network, including modifying the framing type of the network,
resetting the repeater, enabling and disabling individual ports, and
modifying the allowed capabilities of end stations attached to each
port. It is recommended that implementers seriously consider whether
set operations should be allowed without providing, at a minimum,
authentication of request origin.
One particular object in this MIB, vgRptrPortAllowedTrainType, is
considered significant for providing operational security in an
802.12 network. It is recommended that network administrators
configure this object to the 'allowEndNodesOnly' value on all ports
except ports which the administrator knows are attached to cascaded
repeaters or devices which require promiscuous receive capability
(bridges, switches, RMON probes, etc.). This will prevent
unauthorized users from extending the network (by attaching cascaded
repeaters or bridges) without the administrator's knowledge, and will
prevent unauthorized end nodes from listening promiscuously to
network traffic.
Flick Standards Track [Page 54]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
7. Author's Address
John Flick
Hewlett Packard Company
8000 Foothills Blvd. M/S 5556
Roseville, CA 95747-5556
Phone: +1 916 785 4018
Email:
[email protected]
Flick Standards Track [Page 55]
RFC 2266 IEEE 802.12 Repeater MIB January 1998
8. Full Copyright Statement
Copyright (C) The Internet Society (1998). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Flick Standards Track [Page 56]
