Internet Research Task Force (IRTF) M. Mosko
Request for Comments: 8569 PARC, Inc.
Category: Experimental I. Solis
ISSN: 2070-1721 LinkedIn
C. Wood
University of California Irvine
July 2019
Content-Centric Networking (CCNx) Semantics
Abstract
This document describes the core concepts of the Content-Centric
Networking (CCNx) architecture and presents a network protocol based
on two messages: Interests and Content Objects. It specifies the set
of mandatory and optional fields within those messages and describes
their behavior and interpretation. This architecture and protocol
specification is independent of a specific wire encoding.
The protocol also uses a control message called an Interest Return,
whereby one system can return an Interest message to the previous hop
due to an error condition. This indicates to the previous hop that
the current system will not respond to the Interest.
This document is a product of the Information-Centric Networking
Research Group (ICNRG). The document received wide review among
ICNRG participants. Two full implementations are in active use and
have informed the technical maturity of the protocol specification.
Mosko, et al. Experimental [Page 1]
RFC 8569 CCNx Semantics July 2019
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for examination, experimental implementation, and
evaluation.
This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Research Task
Force (IRTF). The IRTF publishes the results of Internet-related
research and development activities. These results might not be
suitable for deployment. This RFC represents the consensus of the
Information-Centric Networking Research Group of the Internet
Research Task Force (IRTF). Documents approved for publication by
the IRSG are not candidates for any level of Internet Standard; see
Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/rfc8569.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(
https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document.
Mosko, et al. Experimental [Page 2]
RFC 8569 CCNx Semantics July 2019
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 5
1.2. Architecture . . . . . . . . . . . . . . . . . . . . . . 5
1.3. Protocol Overview . . . . . . . . . . . . . . . . . . . . 6
2. Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1. Message Grammar . . . . . . . . . . . . . . . . . . . . . 10
2.2. Consumer Behavior . . . . . . . . . . . . . . . . . . . . 14
2.3. Publisher Behavior . . . . . . . . . . . . . . . . . . . 15
2.4. Forwarder Behavior . . . . . . . . . . . . . . . . . . . 16
2.4.1. Interest HopLimit . . . . . . . . . . . . . . . . . . 16
2.4.2. Interest Aggregation . . . . . . . . . . . . . . . . 17
2.4.3. Content Store Behavior . . . . . . . . . . . . . . . 19
2.4.4. Interest Pipeline . . . . . . . . . . . . . . . . . . 19
2.4.5. Content Object Pipeline . . . . . . . . . . . . . . . 20
3. Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.1. Name Examples . . . . . . . . . . . . . . . . . . . . . . 23
3.2. Interest Payload ID . . . . . . . . . . . . . . . . . . . 23
4. Cache Control . . . . . . . . . . . . . . . . . . . . . . . . 23
5. Content Object Hash . . . . . . . . . . . . . . . . . . . . . 24
6. Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7. Hashes . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
8. Validation . . . . . . . . . . . . . . . . . . . . . . . . . 25
8.1. Validation Algorithm . . . . . . . . . . . . . . . . . . 25
8.2. Message Integrity Codes . . . . . . . . . . . . . . . . . 26
8.3. Message Authentication Codes . . . . . . . . . . . . . . 26
8.4. Signature . . . . . . . . . . . . . . . . . . . . . . . . 26
9. Interest to Content Object Matching . . . . . . . . . . . . . 28
10. Interest Return . . . . . . . . . . . . . . . . . . . . . . . 29
10.1. Message Format . . . . . . . . . . . . . . . . . . . . . 30
10.2. ReturnCode Types . . . . . . . . . . . . . . . . . . . . 31
10.3. Interest Return Protocol . . . . . . . . . . . . . . . . 32
10.3.1. No Route . . . . . . . . . . . . . . . . . . . . . . 32
10.3.2. HopLimit Exceeded . . . . . . . . . . . . . . . . . 33
10.3.3. Interest MTU Too Large . . . . . . . . . . . . . . . 33
10.3.4. No Resources . . . . . . . . . . . . . . . . . . . . 33
10.3.5. Path Error . . . . . . . . . . . . . . . . . . . . . 33
10.3.6. Prohibited . . . . . . . . . . . . . . . . . . . . . 33
10.3.7. Congestion . . . . . . . . . . . . . . . . . . . . . 34
10.3.8. Unsupported Content Object Hash Algorithm . . . . . 34
10.3.9. Malformed Interest . . . . . . . . . . . . . . . . . 34
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 34
12. Security Considerations . . . . . . . . . . . . . . . . . . . 34
13. References . . . . . . . . . . . . . . . . . . . . . . . . . 37
13.1. Normative References . . . . . . . . . . . . . . . . . . 37
13.2. Informative References . . . . . . . . . . . . . . . . . 37
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 40
Mosko, et al. Experimental [Page 3]
RFC 8569 CCNx Semantics July 2019
1. Introduction
This document describes the principles of the CCNx architecture. It
describes a network protocol that uses a hierarchical name to forward
requests and to match responses to requests. It does not use
endpoint addresses, such as Internet Protocol. Restrictions in a
request can limit the response by the public key of the response's
signer or the cryptographic hash of the response. Every CCNx
forwarder along the path does the name matching and restriction
checking. The CCNx protocol fits within the broader framework of
Information-Centric Networking (ICN) protocols [RFC7927]. This
document concerns the semantics of the protocol and is not dependent
on a specific wire encoding. The CCNx Messages [RFC8609] document
describes a type-length-value (TLV) wire-protocol encoding. This
section introduces the main concepts of CCNx, which are further
elaborated in the remainder of the document.
The CCNx protocol derives from the early ICN work by Jacobson, et al.
[nnc]. Jacobson's version of CCNx is known as the 0.x version ("CCNx
0.x"), and the present work is known as the 1.0 version ("CCNx 1.0").
There are two active implementations of CCNx 1.0. The most complete
implementation is Community ICN (CICN) [cicn], a Linux Foundation
project hosted at fd.io. Another active implementation is CCN-lite
[ccn-lite], with support for Internet of Things (IoT) systems and the
RIOT operating system. CCNx 0.x formed the basis of the Named Data
Networking (NDN) [ndn] university project.
The current CCNx 1.0 specification diverges from CCNx 0.x in a few
significant areas. The most pronounced behavioral difference between
CCNx 0.x and CCNx 1.0 is that CCNx 1.0 has a simpler response
processing behavior. In both versions, a forwarder uses a
hierarchical longest prefix match of a request name against the
forwarding information base (FIB) to send the request through the
network to a system that can issue a response. A forwarder must then
match a response's name to a request's name to determine the reverse
path and deliver the response to the requester. In CCNx 0.x, the
Interest name may be a hierarchical prefix of the response name,
which allows a form of Layer 3 (L3) content discovery. In CCNx 1.0,
a response's name must exactly equal a request's name. Content
discovery is performed by a higher-layer protocol.
The selector protocol "CCNx Selectors" [selectors] is an example of
using a higher-layer protocol on top of the CCNx 1.0 L3 to perform
content discovery. The selector protocol uses a method similar to
the original CCNx 0.x techniques without requiring partial name
matching of a response to a request in the forwarder.
Mosko, et al. Experimental [Page 4]
RFC 8569 CCNx Semantics July 2019
This document represents the consensus of the Information-Centric
Networking Research Group (ICNRG). It is the first ICN protocol from
the RG, created from the early CCNx protocol [nnc] with significant
revision and input from the ICN community and RG members. This
document has received critical reading by several members of the ICN
community and the RG. The authors and RG chairs approve of the
contents. This document is sponsored under the IRTF, is not issued
by the IETF, and is not an IETF standard. This is an experimental
protocol and may not be suitable for any specific application. The
specification may change in the future.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
1.2. Architecture
We describe the architecture of the network in which CCNx operates
and introduce certain terminology from [terminology]. The detailed
behavior of each component and message grammar is in Section 2.
A producer (also called a "publisher") is an endpoint that
encapsulates content in Content Objects for transport in the CCNx
network. A producer has a public/private keypair and signs (directly
or indirectly) the Content Objects. Usually, the producer's KeyId
(hash of the public key) is well known or may be derived from the
producer's namespace via standard means.
A producer operates within one or more namespaces. A namespace is a
name prefix that is represented in the forwarding information base
(FIB). This allows a request to reach the producer and fetch a
response (if one exists).
The FIB is a table that tells a forwarder where to send a request.
It may point to a local application, a local cache or Content Store,
or to a remote system. If there is no matching entry in the FIB, a
forwarder cannot process a request. The detailed rules on name
matching to the FIB are given in Section 2.4.4. An endpoint has a
FIB, though it may be a simple default route. An intermediate system
(i.e., a router) typically has a much larger FIB. A core CCNx
forwarder, for example, would know all the global routes.
Mosko, et al. Experimental [Page 5]
RFC 8569 CCNx Semantics July 2019
A consumer is an endpoint that requests a name. It is beyond the
scope of this document to describe how a consumer learns of a name or
publisher KeyId; higher-layer protocols built on top of CCNx handle
those tasks, such as search engines or lookup services or well-known
names. The consumer constructs a request, called an Interest, and
forwards it via the endpoint's FIB. The consumer should get back
either a response (called a Content Object) that matches the Interest
or a control message (called an Interest Return) that indicates the
network cannot handle the request.
There are three ways to detect errors in Interest handling. An
Interest Return is a network control message that indicates a low-
level error like "no route" or "out of resources". If an Interest
arrives at a producer, but the producer does not have the requested
content, the producer should send an application-specific error
message (e.g., a "not found" message). Finally, a consumer may not
receive anything; in which case, it should timeout and, depending on
the application, retry the request or return an error to the
application.
1.3. Protocol Overview
The goal of CCNx is to name content and retrieve the content from the
network without binding it to a specific network endpoint. A routing
system (specified separately) populates the FIB tables at each CCNx
router with hierarchical name prefixes that point towards the content
producers under that prefix. A request finds matching content along
those paths, in which case a response carries the data, or, if no
match is found, a control message indicates the failure. A request
may further refine acceptable responses with a restriction on the
response's signer and the cryptographic hash of the response. The
details of these restrictions are described below.
The CCNx name is a hierarchical series of name segments. Each name
segment has a type and zero or more bytes. Matching two names is
done as a binary comparison of the type and value, and is done
segment by segment. The human-readable form is defined under a URI
scheme "ccnx:" [ccnx-uri], though the canonical encoding of a name is
a series of pairs (type, octet string). There is no requirement that
any name segment be human readable or UTF-8. The first few segments
in a name will be matched against the FIB, and a routing protocol may
put its own restrictions on the routable name components (e.g., a
maximum length or character-encoding rules). In principle, name
segments and names have unbounded length, though in practice they are
limited by the wire encoding and practical considerations imposed by
a routing protocol. Note that in CCNx, name segments use binary
comparison, whereas in a URI, the authority uses a case-insensitive
hostname (due to DNS).
Mosko, et al. Experimental [Page 6]
RFC 8569 CCNx Semantics July 2019
The CCNx name, as used by the forwarder, is purposefully left as a
general octet-encoded type and value without any requirements on
human readability and character encoding. The reason for this is
that we are concerned with how a forwarder processes names. We
expect that applications, routing protocols, or other higher layers
will apply their own conventions and restrictions on the allowed name
segment types and name segment values.
CCNx is a request and response protocol that fetches chunks of data
using a name. The integrity of each chunk may be directly asserted
through a digital signature or Message Authentication Code (MAC), or,
alternatively, indirectly via hash chains. Chunks may also carry
weaker Message Integrity Codes (MICs) or no integrity protection
mechanism at all. Because provenance information is carried with
each chunk (or larger indirectly protected block), we no longer need
to rely on host identities, such as those derived from TLS
certificates, to ascertain the chunk legitimacy. Therefore, data
integrity is a core feature of CCNx; it does not rely on the data
transmission channel. There are several options for data
confidentiality, discussed later.
This document only defines the general properties of CCNx names. In
some isolated environments, CCNx users may be able to use any name
they choose and either inject that name (or prefix) into a routing
protocol or use other information foraging techniques. In the
Internet environment, there will be policies around the formats of
names and assignments of names to publishers, though those are not
specified here.
The key concept of CCNx is that a subjective name is
cryptographically bound to a fixed payload. These publisher-
generated bindings can therefore be cryptographically verified. A
named payload is thus the tuple {{Name, ExtraFields, Payload,
ValidationAlgorithm}, ValidationPayload}, where all fields in the
inner tuple are covered by the validation payload (e.g., signature).
Consumers of this data can check the binding integrity by recomputing
the same cryptographic hash and verifying the digital signature in
ValidationPayload.
In addition to digital signatures (e.g., RSA), CCNx also supports
message authentication codes (e.g., Hashed Message Authentication
Code (HMAC)) and message integrity codes (e.g., Cyclic Redundancy
Checks (CRC)). To maintain the cryptographic binding, there should
be at least one object with a signature or authentication code, but
not all objects require it. For example, a first object with a
signature could refer to other objects via a hash chain, a Merkle
tree, or a signed manifest. The later objects may not have any
Mosko, et al. Experimental [Page 7]
RFC 8569 CCNx Semantics July 2019
validation and rely purely on the references. The use of an
integrity code (e.g., CRC) is intended for detecting accidental
corruption in an Interest.
CCNx specifies a network protocol around Interests (request messages)
and Content Objects (response messages) to move named payloads. An
Interest includes the Name field, which identifies the desired
response, and optional matching restrictions. Restrictions limit the
possible matching Content Objects. Two restrictions exist: the Key
ID restriction (KeyIdRestr) and Content Object Hash restriction
(ContentObjectHashRestr). The first restriction on the KeyId limits
responses to those signed with a ValidationAlgorithm KeyId field
equal to the restriction. The second is the Content Object Hash
restriction, which limits the response to one where the cryptographic
hash of the entire named payload is equal to the restriction.
Section 9 fully explains how these restrictions limit matching of a
Content Object to an Interest.
The hierarchy of a CCNx name is used for routing via the longest
matching prefix in a forwarder. The longest matching prefix is
computed name segment by name segment in the hierarchical name, where
each name segment must be exactly equal to match. There is no
requirement that the prefix be globally routable. Within a
deployment, any local routing may be used, even one that only uses a
single flat (nonhierarchical) name segment.
Another concept of CCNx is that there should be flow balance between
Interest messages and Content Object messages. At the network level,
an Interest traveling along a single path should elicit no more than
one Content Object response. If some node sends the Interest along
more than one path, that node should consolidate the responses such
that only one Content Object flows back towards the requester. If an
Interest is sent broadcast or multicast on a multiple-access media,
the sender should be prepared for multiple responses unless some
other media-dependent mechanism like gossip suppression or leader
election is used.
As an Interest travels the forward path following the FIB, it
establishes state at each forwarder such that a Content Object
response can trace its way back to the original requester(s) without
the requester needing to include a routable return address. We use
the notional Pending Interest Table (PIT) as a method to store state
that facilitates the return of a Content Object.
The notional PIT stores the last hop of an Interest plus its Name
field and optional restrictions. This is the data required to match
a Content Object to an Interest (see Section 9). When a Content
Mosko, et al. Experimental [Page 8]
RFC 8569 CCNx Semantics July 2019
Object arrives, it must be matched against the PIT to determine which
entries it satisfies. For each such entry, at most one copy of the
Content Object is sent to each listed last hop in the PIT entries.
An actual PIT is not mandated by this specification. An
implementation may use any technique that gives the same external
behavior. There are, for example, research papers that use
techniques like label switching in some parts of the network to
reduce the per-node state incurred by the PIT [dart]. Some
implementations store the PIT state in the FIB, so there is not a
second table.
If multiple Interests with the same {Name, [KeyIdRestr],
[ContentObjectHashRestr]} tuple arrive at a node before a Content
Object matching the first Interest comes back, they are grouped in
the same PIT entry and their last hops are aggregated (see
Section 2.4.2). Thus, one Content Object might satisfy multiple
pending Interests in a PIT.
In CCNx, higher-layer protocols are often called "name-based
protocols" because they operate on the CCNx name. For example, a
versioning protocol might append additional name segments to convey
state about the version of payload. A content discovery protocol
might append certain protocol-specific name segments to a prefix to
discover content under that prefix. Many such protocols may exist
and apply their own rules to names. They may be layered with each
protocol encapsulating (to the left) a higher layer's name prefix.
This document also describes a control message called an Interest
Return. A network element may return an Interest message to a
previous hop if there is an error processing the Interest. The
returned Interest may be further processed at the previous hop or
returned towards the Interest origin. When a node returns an
Interest, it indicates that the previous hop should not expect a
response from that node for the Interest, i.e., there is no PIT entry
left at the returning node for a Content Object to follow.
There are multiple ways to describe larger objects in CCNx.
Aggregating L3 Content Objects into larger objects is beyond the
scope of this document. One proposed method, File-Like ICN
Collection (FLIC) [flic], uses a manifest to enumerate the pieces of
a larger object. Manifests are, themselves, Content Objects.
Another option is to use a convention in the Content Object name, as
in the CCNx Chunking [chunking] protocol where a large object is
broken into small chunks and each chunk receives a special name
component indicating its serial order.
Mosko, et al. Experimental [Page 9]
RFC 8569 CCNx Semantics July 2019
At the semantic level, described in this document, we do not address
fragmentation. One experimental fragmentation protocol, BeginEnd
Fragments [befrags], uses a multipoint PPP-style technique for use
over L2 interfaces with the specification for CCNx Messages [RFC8609]
in TLV wire encoding.
With these concepts, the remainder of the document specifies the
behavior of a forwarder in processing Interest, Content Object, and
Interest Return messages.
2. Protocol
This section defines the grammar of a CCNx Message (Interest, Content
Object, or Interest Return). It then presents typical behaviors for
a consumer, a publisher, and a forwarder. In the forwarder section,
there are detailed descriptions about how to handle the forwarder-
specific topics, such as HopLimit and Content Store, along with
detailed processing pipelines for Interest and Content Object
messages.
2.1. Message Grammar
The CCNx Message ABNF [RFC5234] grammar is shown in Figure 1. The
grammar does not include any encoding delimiters, such as TLVs.
Specific wire encodings are given in a separate document. If a
Validation section exists, the Validation Algorithm covers from the
Body (BodyName or BodyOptName) through the end of the ValidationAlg
section. The InterestLifetime, CacheTime, and Return Code fields
exist outside of the validation envelope and may be modified.
HashType, PayloadType, and Private Enterprise Number (PEN) need to
correspond to IANA values registered in the "CCNx Hash Function
Types" and "CCNx Payload Types" registries [ccnx-registry], as well
as the "Private Enterprise Numbers" registry [eprise-numbers],
respectively.
The various fields, in alphabetical order, are defined as:
AbsTime: Absolute times are conveyed as the 64-bit UTC time in
milliseconds since the epoch (standard POSIX time).
CacheTime: The absolute time after which the publisher believes
there is low value in caching the Content Object. This is a
recommendation to caches (see Section 4).
Cert: Some applications may wish to embed an X.509 certificate to
both validate the signature and provide a trust anchor. The Cert
is a DER-encoded X.509 certificate.
Mosko, et al. Experimental [Page 10]
RFC 8569 CCNx Semantics July 2019
ConObjField: These are optional fields that may appear in a Content
Object.
ConObjHash: The value of the Content Object Hash, which is the
SHA256-32 over the message from the beginning of the body to the
end of the message. Note that this coverage area is different
from the ValidationAlg. This value SHOULD NOT be trusted across
domains (see Section 5).
ContentObjectHashRestr: The Content Object Hash restriction. A
Content Object must hash to the same value as the restriction
using the same HashType. The ContentObjectHashRestr MUST use
SHA256-32.
ExpiryTime: An absolute time after which the Content Object should
be considered expired (see Section 4).
Hash: Hash values carried in a Message carry a HashType to identify
the algorithm used to generate the hash followed by the hash
value. This form is to allow hash agility. Some fields may
mandate a specific HashType.
HashType: The algorithm used to calculate a hash, which must
correspond to one of the IANA "CCNx Hash Function Types"
[ccnx-registry].
HopLimit: Interest messages may loop if there are loops in the
forwarding plane. To eventually terminate loops, each Interest
carries a HopLimit that is decremented after each hop and no
longer forwarded when it reaches zero. See Section 2.4.
InterestField: These are optional fields that may appear in an
Interest message.
KeyId: An identifier for the key used in the ValidationAlg. See
Validation (Section 8) for a description of how it is used for
MACs and signatures.
KeyIdRestr: The KeyId Restriction. A Content Object must have a
KeyId with the same value as the restriction.
KeyLink: A Link (see Section 6) that names how to retrieve the key
used to verify the ValidationPayload (see Section 8).
Lifetime: The approximate time during which a requester is willing
to wait for a response, usually measured in seconds. It is not
strongly related to the network round-trip time, though it must
necessarily be larger.
Mosko, et al. Experimental [Page 11]
RFC 8569 CCNx Semantics July 2019
Name: A name is made up of a nonempty first segment followed by zero
or more additional segments, which may be of 0 length. Name
segments are opaque octet strings and are thus case sensitive if
encoding UTF-8. An Interest MUST have a Name. A Content Object
MAY have a Name (see Section 9). The segments of a name are said
to be complete if its segments uniquely identify a single Content
Object. A name is exact if its segments are complete. An
Interest carrying a full name is one that specifies an exact name
and the Content Object Hash restriction of the corresponding
Content Object.
Payload: The message's data, as defined by PayloadType.
PayloadType: The format of the Payload field. If missing, assume
Data type (T_PAYLOADTYPE_DATA) [ccnx-registry]. Data type means
the payload is opaque application bytes. Key type
(T_PAYLOADTYPE_KEY [ccnx-registry]) means the payload is a DER-
encoded public key or X.509 certificate. Link type
(T_PAYLOADTYPE_LINK [ccnx-registry]) means it is one or more Links
(see Section 6).
PublicKey: Some applications may wish to embed the public key used
to verify the signature within the message itself. The PublickKey
is DER encoded.
RelTime: A relative time, measured in milliseconds.
ReturnCode: States the reason an Interest message is being returned
to the previous hop (see Section 10.2).
SigTime: The absolute time (UTC milliseconds) when the signature was
generated. The signature time only applies to the validation
algorithm; it does not necessarily represent when the validated
message was created.
Vendor: Vendor-specific opaque data. The Vendor data includes the
IANA Private Enterprise Numbers [eprise-numbers], followed by
vendor-specific information. CCNx allows vendor-specific data in
most locations of the grammar.
Message = Interest / ContentObject / InterestReturn
Interest = IntHdr BodyName [Validation]
IntHdr = HopLimit [Lifetime] *Vendor
ContentObject = ConObjHdr BodyOptName [Validation]
ConObjHdr = [CacheTime / ConObjHash] *Vendor
InterestReturn= ReturnCode Interest
BodyName = Name Common
BodyOptName = [Name] Common
Mosko, et al. Experimental [Page 12]
RFC 8569 CCNx Semantics July 2019
Common = *Field [Payload]
Validation = ValidationAlg ValidationPayload
Name = FirstSegment *Segment
FirstSegment = 1*OCTET / Vendor
Segment = *OCTET / Vendor
ValidationAlg = (RSA-SHA256 / EC-SECP-256K1 / EC-SECP-384R1 /
HMAC-SHA256 / CRC32C) *Vendor
ValidationPayload = 1*OCTET
PublicAlg = KeyId [SigTime] [KeyLink] [PublicKey] [Cert]
RSA-SHA256 = PublicAlg
EC-SECP-256K1 = PublicAlg
EC-SECP-384R1 = PublicAlg
HMAC-SHA256 = KeyId [SigTime] [KeyLink]
CRC32C = [SigTime]
AbsTime = 8OCTET ; 64-bit UTC msec since epoch
CacheTime = AbsTime
ConObjField = ExpiryTime / PayloadType
ConObjHash = Hash
ExpiryTime = AbsTime
Field = InterestField / ConObjField / Vendor
Hash = HashType 1*OCTET
HashType = 2OCTET ; IANA "CCNx Hash Function Types"
HopLimit = OCTET
InterestField = KeyIdRestr / ContentObjectHashRestr
KeyId = Hash
KeyIdRestr = Hash
KeyLink = Link
Lifetime = RelTime
Link = Name [KeyIdRestr] [ContentObjectHashRestr]
ContentObjectHashRestr = Hash
Payload = *OCTET
PayloadType = OCTET ; IANA "CCNx Payload Types"
PublicKey = *OCTET ; DER-encoded public key
Cert = *OCTET ; DER-encoded X.509 Certificate
RelTime = 1*OCTET ; msec
ReturnCode = OCTET ; see Section 10.2
SigTime = AbsTime
Vendor = PEN *OCTET
PEN = 1*OCTET ; IANA "Private Enterprise Number"
Figure 1: CCNx Message ABNF Grammar
Mosko, et al. Experimental [Page 13]
RFC 8569 CCNx Semantics July 2019
2.2. Consumer Behavior
To request a piece of content for a given {Name, [KeyIdRest],
[ContentObjectHashRestr]} tuple, a consumer creates an Interest
message with those values. It MAY add a validation section,
typically only a CRC32C. A consumer MAY put a Payload field in an
Interest to send additional data to the producer beyond what is in
the name. The name is used for routing and may be remembered at each
hop in the notional PIT to facilitate returning a Content Object;
storing large amounts of state in the name could lead to high memory
requirements. Because the payload is not considered when forwarding
an Interest or matching a Content Object to an Interest, a consumer
SHOULD put an Interest Payload ID (see Section 3.2) as part of the
name to allow a forwarder to match Interests to Content Objects and
avoid aggregating Interests with different payloads. Similarly, if a
consumer uses a MAC or a signature, it SHOULD also include a unique
segment as part of the name to prevent the Interest from being
aggregated with other Interests or satisfied by a Content Object that
has no relation to the validation.
The consumer SHOULD specify an InterestLifetime, which is the length
of time the consumer is willing to wait for a response. The
InterestLifetime is an application-scale time, not a network round-
trip time (see Section 2.4.2). If not present, the InterestLifetime
will use a default value (2 seconds).
The consumer SHOULD set the Interest HopLimit to a reasonable value
or use the default 255. If the consumer knows the distances to the
producer via routing, it SHOULD use that value.
A consumer hands off the Interest to its first forwarder, which will
then forward the Interest over the network to a publisher (or
replica) that may satisfy it based on the name (see Section 2.4).
Interest messages are unreliable. A consumer SHOULD run a transport
protocol that will retry the Interest if it goes unanswered, up to
the InterestLifetime. No transport protocol is specified in this
document.
The network MAY send to the consumer an Interest Return message that
indicates the network cannot fulfill the Interest. The ReturnCode
specifies the reason for the failure, such as no route or congestion.
Depending on the ReturnCode, the consumer MAY retry the Interest or
MAY return an error to the requesting application.
Mosko, et al. Experimental [Page 14]
RFC 8569 CCNx Semantics July 2019
If the content was found and returned by the first forwarder, the
consumer will receive a Content Object. The consumer uses the
following set of checks to validate a received Content Object:
o The consumer MUST ensure the Content Object is properly formatted.
o The consumer MUST verify that the returned Content Object matches
one or more pending Interests as per Section 9.
o If the Content Object is signed, the consumer SHOULD
cryptographically verify the signature as per Section 8. If it
does not have the corresponding key, it SHOULD fetch the key, such
as from a key resolution service or via the KeyLink.
o If the signature has a SigTime, the consumer MAY use that in
considering if the signature is valid. For example, if the
consumer is asking for dynamically generated content, it should
expect the SigTime not to be before the time the Interest was
generated.
o If the Content Object is signed, the consumer SHOULD assert the
trustworthiness of the signing key to the namespace. Such an
assertion is beyond the scope of this document, though one may use
traditional PKI methods, a trusted key resolution service, or
methods like [trust].
o The consumer MAY cache the Content Object for future use, up to
the ExpiryTime if present.
o The consumer MAY accept a Content Object off the wire that is
expired. A packet Content Object may expire while in flight;
there is no requirement that forwarders drop expired packets in
flight. The only requirement is that Content Stores, caches, or
producers MUST NOT respond with an expired Content Object.
2.3. Publisher Behavior
This document does not specify the method by which names populate a
FIB table at forwarders (see Section 2.4). A publisher is either
configured with one or more name prefixes under which it may create
content or it chooses its name prefixes and informs the routing layer
to advertise those prefixes.
When a publisher receives an Interest, it SHOULD:
o Verify that the Interest is part of the publisher's namespace(s).
Mosko, et al. Experimental [Page 15]
RFC 8569 CCNx Semantics July 2019
o If the Interest has a Validation section, verify it as per
Section 8. Usually an Interest will only have a CRC32C, unless
the publisher application specifically accommodates other
validations. The publisher MAY choose to drop Interests that
carry a Validation section if the publisher application does not
expect those signatures, as this could be a form of computational
denial of service. If the signature requires a key that the
publisher does not have, it is NOT RECOMMENDED that the publisher
fetch the key over the network unless it is part of the
application's expected behavior.
o Retrieve or generate the requested Content Object and return it to
the Interest's previous hop. If the requested content cannot be
returned, the publisher SHOULD reply with an Interest Return or a
Content Object with application payload that says the content is
not available; this Content Object should have a short ExpiryTime
in the future or not be cacheable (i.e., an expiry time of 0).
2.4. Forwarder Behavior
A forwarder routes Interest messages based on a Forwarding
Information Base (FIB), returns Content Objects that match Interests
to the Interest's previous hop, and processes Interest Return control
messages. It may also keep a cache of Content Objects in the
notional Content Store table. This document does not specify the
internal behavior of a forwarder, only these and other external
behaviors.
In this document, we will use two processing pipelines: one for
Interests and one for Content Objects. Interest processing is made
up of checking for duplicate Interests in the PIT (see
Section 2.4.2), checking for a cached Content Object in the Content
Store (see Section 2.4.3), and forwarding an Interest via the FIB.
Content Store processing is made up of checking for matching
Interests in the PIT and forwarding to those previous hops.
2.4.1. Interest HopLimit
Interest looping is not prevented in CCNx. An Interest traversing
loops is eventually discarded using the hop-limit field of the
Interest, which is decremented at each hop traversed by the Interest.
A loop may also terminate because the Interest is aggregated with its
previous PIT entry along the loop. In this case, the Content Object
will be sent back along the loop and eventually return to a node that
already forwarded the content, so it will likely not have a PIT entry
anymore. When the content reaches a node without a PIT entry, it
Mosko, et al. Experimental [Page 16]
RFC 8569 CCNx Semantics July 2019
will be discarded. It may be that a new Interest or another looped
Interest will return to that same node, in which case the node will
return a cached response to make a new PIT entry, as below.
The HopLimit is the last resort method to stop Interest loops where a
Content Object chases an Interest around a loop and where the
intermediate nodes, for whatever reason, no longer have a PIT entry
and do not cache the Content Object.
Every Interest MUST carry a HopLimit. An Interest received from a
local application MAY have a 0 HopLimit, which restricts the Interest
to other local sources.
When an Interest is received from another forwarder, the HopLimit
MUST be positive, otherwise the forwarder will discard the Interest.
A forwarder MUST decrement the HopLimit of an Interest by at least 1
before it is forwarded.
If the decremented HopLimit equals 0, the Interest MUST NOT be
forwarded to another forwarder; it MAY be sent to a local publisher
application or serviced from a local Content Store.
A RECOMMENDED HopLimit-processing pipeline is below:
o If Interest received from a remote system:
* If received HopLimit is 0, optionally send Interest Return
(HopLimit Exceeded), and discard Interest.
* Otherwise, decrement the HopLimit by 1.
o Process as per Content Store and Aggregation rules.
o If the Interest will be forwarded:
* If the (potentially decremented) HopLimit is 0, restrict
forwarding to the local system.
* Otherwise, forward as desired to local or remote systems.
2.4.2. Interest Aggregation
Interest aggregation is when a forwarder receives an Interest message
that could be satisfied by the response to another Interest message
already forwarded by the node, so the forwarder suppresses forwarding
the new Interest; it only records the additional previous hop so a
Content Object sent in response to the first Interest will satisfy
both Interests.
Mosko, et al. Experimental [Page 17]
RFC 8569 CCNx Semantics July 2019
CCNx uses an Interest aggregation rule that assumes the
InterestLifetime is akin to a subscription time and is not a network
round-trip time. Some previous aggregation rules assumed the
lifetime was a round-trip time, but this leads to problems of
expiring an Interest before a response comes if the RTT is estimated
too short or interfering with an Automatic Repeat reQuest (ARQ)
scheme that wants to retransmit an Interest but a prior Interest
overestimated the RTT.
A forwarder MAY implement an Interest aggregation scheme. If it does
not, then it will forward all Interest messages. This does not imply
that multiple, possibly identical, Content Objects will come back. A
forwarder MUST still satisfy all pending Interests, so one Content
Object could satisfy multiple similar Interests, even if the
forwarder did not suppress duplicate Interest messages.
A RECOMMENDED Interest aggregation scheme is:
o Two Interests are considered "similar" if they have the same Name,
KeyIdRestr, and ContentObjectHashRestr, where a missing optional
field in one must be missing in the other.
o Let the notional value InterestExpiry (a local value at the
forwarder) be equal to the receive time plus the InterestLifetime
(or a platform-dependent default value if not present).
o An Interest record (PIT entry) is considered invalid if its
InterestExpiry time is in the past.
o The first reception of an Interest MUST be forwarded.
o A second or later reception of an Interest similar to a valid
pending Interest from the same previous hop MUST be forwarded. We
consider these a retransmission request.
o A second or later reception of an Interest similar to a valid
pending Interest from a new previous hop MAY be aggregated (not
forwarded). If this Interest has a larger HopLimit than the
pending Interest, it MUST be forwarded.
o Aggregating an Interest MUST extend the InterestExpiry time of the
Interest record. An implementation MAY keep a single
InterestExpiry time for all previous hops or MAY keep the
InterestExpiry time per previous hop. In the first case, the
forwarder might send a Content Object down a path that is no
longer waiting for it, in which case the previous hop (next hop of
the Content Object) would drop it.
Mosko, et al. Experimental [Page 18]
RFC 8569 CCNx Semantics July 2019
2.4.3. Content Store Behavior
The Content Store is a special cache that is an integral part of a
CCNx forwarder. It is an optional component. It serves to repair
lost packets and handle flash requests for popular content. It could
be prepopulated or use opportunistic caching. Because the Content
Store could serve to amplify an attack via cache poisoning, there are
special rules about how a Content Store behaves.
1. A forwarder MAY implement a Content Store. If it does, the
Content Store matches a Content Object to an Interest via the
normal matching rules (see Section 9).
2. If an Interest has a KeyId restriction, then the Content Store
MUST NOT reply unless it knows the signature on the matching
Content Object is correct. It may do this by external knowledge
(i.e., in a managed network or system with prepopulated caches)
or by having the public key and cryptographically verifying the
signature. A Content Store is NOT REQUIRED to verify signatures;
if it does not, then it treats these cases like a cache miss.
3. If a Content Store chooses to verify signatures, then it MAY do
so as follows. If the public key is provided in the Content
Object itself (i.e., in the PublicKey field) or in the Interest,
the Content Store MUST verify that the public key's hash is equal
to the KeyId and that it verifies the signature (see
Section 8.4). A Content Store MAY verify the digital signature
of a Content Object before it is cached, but it is not required
to do so. A Content Store SHOULD NOT fetch keys over the
network. If it cannot or has not yet verified the signature, it
should treat the Interest as a cache miss.
4. If an Interest has a Content Object Hash restriction, then the
Content Store MUST NOT reply unless it knows the matching Content
Object has the correct hash. If it cannot verify the hash, then
it should treat the Interest as a cache miss.
5. It must obey the cache control directives (see Section 4).
2.4.4. Interest Pipeline
1. Perform the HopLimit check (see Section 2.4.1).
2. If the Interest carries a validation, such as a MIC or a
signature with an embedded public key or certificate, a forwarder
MAY validate the Interest as per Section 8. A forwarder SHOULD
NOT fetch keys via a KeyLink. If the forwarder drops an Interest
Mosko, et al. Experimental [Page 19]
RFC 8569 CCNx Semantics July 2019
due to failed validation, it MAY send an Interest Return
(Section 10.3.9).
3. Determine if the Interest can be aggregated as per Section 2.4.2.
If it can be, aggregate and do not forward the Interest.
4. If forwarding the Interest, check for a hit in the Content Store
as per Section 2.4.3. If a matching Content Object is found,
return it to the Interest's previous hop. This injects the
Content Store as per Section 2.4.5.
5. Look up the Interest in the FIB. Longest Prefix Match (LPM) is
performed name segment by name segment (not byte or bit). It
SHOULD exclude the Interest's previous hop. If a match is found,
forward the Interest. If no match is found or the forwarder
chooses not to forward due to a local condition (e.g.,
congestion), it SHOULD send an Interest Return message as per
Section 10.
2.4.5. Content Object Pipeline
1. It is RECOMMENDED that a forwarder that receives a Content Object
check that the Content Object came from an expected previous hop.
An expected previous hop is one pointed to by the FIB or one
recorded in the PIT as having had a matching Interest sent that
way.
2. A Content Object MUST be matched to all pending Interests that
satisfy the matching rules (see Section 9). Each satisfied
pending Interest MUST then be removed from the set of pending
Interests.
3. A forwarder SHOULD NOT send more than one copy of the received
Content Object to the same Interest previous hop. It may happen,
for example, that two Interests ask for the same Content Object
in different ways (e.g., by name and by name and KeyId), and that
they both come from the same previous hop. It is normal to send
the same Content Object multiple times on the same interface,
such as Ethernet, if it is going to different previous hops.
4. A Content Object SHOULD only be put in the Content Store if it
satisfied an Interest (and passed rule #1 above). This is to
reduce the chances of cache poisoning.
Mosko, et al. Experimental [Page 20]
RFC 8569 CCNx Semantics July 2019
3. Names
A CCNx name is a composition of name segments. Each name segment
carries a label identifying the purpose of the name segment, and a
value. For example, some name segments are general names and some
serve specific purposes such as carrying version information or the
sequencing of many chunks of a large object into smaller, signed
Content Objects.
There are three different types of names in CCNx: prefix, exact, and
full names. A prefix name is simply a name that does not uniquely
identify a single Content Object, but rather a namespace or prefix of
an existing Content Object name. An exact name is one that uniquely
identifies the name of a Content Object. A full name is one that is
exact and is accompanied by an explicit or implicit ConObjHash. The
ConObjHash is explicit in an Interest and implicit in a Content
Object.
Note that a forwarder does not need to know any semantics about a
name. It only needs to be able to match a prefix to forward
Interests and match an exact or full name to forward Content Objects.
It is not sensitive to the name segment types.
The name segment labels specified in this document are given in
Table 1. Name Segment is a general name segment, typically occurring
in the routable prefix and user-specified content name. Interest
Payload ID is a name segment to identify the Interest's payload.
Application Components are a set of name segment types reserved for
application use.
Mosko, et al. Experimental [Page 21]
RFC 8569 CCNx Semantics July 2019
+-------------+-----------------------------------------------------+
| Type | Description |
+-------------+-----------------------------------------------------+
| Name | A generic name segment that includes arbitrary |
| Segment | octets. |
| | |
| Interest | An octet string that identifies the payload carried |
| Payload ID | in an Interest. As an example, the Payload ID |
| | might be a hash of the Interest Payload. This |
| | provides a way to differentiate between Interests |
| | based on the payload solely through a name segment |
| | without having to include all the extra bytes of |
| | the payload itself. |
| | |
| Application | An application-specific payload in a name segment. |
| Components | An application may apply its own semantics to these |
| | components. A good practice is to identify the |
| | application in a name segment prior to the |
| | application component segments. |
+-------------+-----------------------------------------------------+
Table 1: CCNx Name Segment Types
At the lowest level, a forwarder does not need to understand the
semantics of name segments; it need only identify name segment
boundaries and be able to compare two name segments (both label and
value) for equality. The forwarder matches names segment by segment
against its forwarding table to determine a next hop.
Mosko, et al. Experimental [Page 22]
RFC 8569 CCNx Semantics July 2019
3.1. Name Examples
This section uses the CCNx URI [ccnx-uri] representation of CCNx
names. Note that as per the message grammar, an Interest must have a
Name with at least one name segment that must have at least 1 octet
of value. A Content Object must have a similar name or no name at
all. The FIB, on the other hand, could have 0-length names (a
default route), or a first name segment with no value, or a regular
name.
+--------------------------+----------------------------------------+
| Name | Description |
+--------------------------+----------------------------------------+
| ccnx:/ | A 0-length name, corresponds to a |
| | default route. |
| | |
| ccnx:/NAME= | A name with 1 segment of 0 length, |
| | distinct from ccnx:/. |
| | |
| ccnx:/NAME=foo/APP:0=bar | A 2-segment name, where the first |
| | segment is of type NAME and the second |
| | segment is of type APP:0. |
+--------------------------+----------------------------------------+
Table 2: CCNx Name Examples
3.2. Interest Payload ID
An Interest may also have a Payload field that carries state about
the Interest but is not used to match a Content Object. If an
Interest contains a payload, the Interest name should contain an
Interest Payload ID (IPID). The IPID allows a PIT entry to correctly
multiplex Content Objects in response to a specific Interest with a
specific payload ID. The IPID could be derived from a hash of the
payload or could be a Globally Unique Identifier (GUID) or a nonce.
An optional Metadata field defines the IPID field so other systems
can verify the IPID, such as when it is derived from a hash of the
payload. No system is required to verify the IPID.
4. Cache Control
CCNx supports two fields that affect cache control. These determine
how a cache or Content Store handles a Content Object. They are not
used in the fast path; they are only used to determine if a Content
Object can be injected onto the fast path in response to an Interest.
The ExpiryTime is a field that exists within the signature envelope
of a Validation Algorithm. It is the UTC time in milliseconds after
Mosko, et al. Experimental [Page 23]
RFC 8569 CCNx Semantics July 2019
which the Content Object is considered expired and MUST no longer be
used to respond to an Interest from a cache. Stale content MAY be
flushed from the cache.
The Recommended Cache Time (RCT) is a field that exists outside the
signature envelope. It is the UTC time in milliseconds after which
the publisher considers the Content Object to be of low value to
cache. A cache SHOULD discard it after the RCT, though it MAY keep
it and still respond with it. A cache MAY also discard the Content
Object before the RCT time; there is no contractual obligation to
remember anything.
This formulation allows a producer to create a Content Object with a
long ExpiryTime but short RCT and keep republishing the same signed
Content Object over and over again by extending the RCT. This allows
a form of "phone home" where the publisher wants to periodically see
that the content is being used.
5. Content Object Hash
CCNx allows an Interest to restrict a response to a specific hash.
The hash covers the Content Object message body and the validation
sections, if present. Thus, if a Content Object is signed, its hash
includes that signature value. The hash does not include the fixed
or hop-by-hop headers of a Content Object. Because it is part of the
matching rules (see Section 9), the hash is used at every hop.
There are two options for matching the Content Object Hash
restriction in an Interest. First, a forwarder could compute for
itself the hash value and compare it to the restriction. This is an
expensive operation. The second option is for a border device to
compute the hash once and place the value in a header (ConObjHash)
that is carried through the network. The second option, of course,
removes any security properties from matching the hash, so it SHOULD
only be used within a trusted domain. The header SHOULD be removed
when crossing a trust boundary.
6. Link
A Link is the tuple {Name, [KeyIdRestr], [ContentObjectHashRestr]}.
The information in a Link comprises the fields of an Interest that
would retrieve the Link target. A Content Object with PayloadType of
"Link" is an object whose payload is one or more Links. This tuple
may be used as a KeyLink to identify a specific object with the
certificate-wrapped key. It is RECOMMENDED to include at least one
of either KeyId restriction or Content Object Hash restriction. If
neither restriction is present, then any Content Object with a
matching name from any publisher could be returned.
Mosko, et al. Experimental [Page 24]
RFC 8569 CCNx Semantics July 2019
7. Hashes
Several protocol fields use cryptographic hash functions, which must
be secure against attack and collisions. Because these hash
functions change over time, with better ones appearing and old ones
falling victim to attacks, it is important that a CCNx protocol
implementation supports hash agility.
In this document, we suggest certain hashes (e.g., SHA-256), but a
specific implementation may use what it deems best. The normative
CCNx Messages [RFC8609] specification should be taken as the
definition of acceptable hash functions and uses.
8. Validation
8.1. Validation Algorithm
The Validator consists of a ValidationAlgorithm that specifies how to
verify the message and a ValidationPayload containing the validation
output, e.g., the digital signature or MAC. The ValidationAlgorithm
section defines the type of algorithm to use and includes any
necessary additional information. The validation is calculated from
the beginning of the CCNx Message through the end of the
ValidationAlgorithm section (i.e., up to but not including the
validation payload). We refer to this as the validation region. The
ValidationPayload is the integrity value bytes, such as a MAC or
signature.
The CCNx Message Grammar (Section 2.1) shows the allowed validation
algorithms and their structure. In the case of a Vendor algorithm,
the vendor may use any desired structure. A Validator can only be
applied to an Interest or a Content Object, not an Interest Return.
An Interest inside an Interest Return would still have the original
validator, if any.
The grammar allows multiple Vendor extensions to the validation
algorithm. It is up to the vendor to describe the validation region
for each extension. A vendor may, for example, use a regular
signature in the validation algorithm, then append a proprietary MIC
to allow for in-network error checking without using expensive
signature verification. As part of this specification, we do not
allow for multiple Validation Algorithm blocks apart from these
vendor methods.
Mosko, et al. Experimental [Page 25]
RFC 8569 CCNx Semantics July 2019
8.2. Message Integrity Codes
If the validation algorithm is CRC32C, then the validation payload is
the output of the CRC over the validation region. This validation
algorithm allows for an optional signature time (SigTime) to
timestamp when the message was validated (calling it a "signature"
time is a slight misnomer, but we reuse the same field for this
purpose between MICs, MACs, and signatures).
MICs are usually used with an Interest to avoid accidental in-network
corruption. They are usually not used on Content Objects because the
objects are either signed or linked to by hash chains, so the CRC32C
is redundant.
8.3. Message Authentication Codes
If the validation algorithm is HMAC-SHA256, then the validation
payload is the output of the HMAC over the validation region. The
validation algorithm requires a KeyId and allows for a signature time
(SigTime) and KeyLink.
The KeyId field identifies the shared secret used between two parties
to authenticate messages. These secrets SHOULD be derived from a key
exchange protocol such as [ccnx-ke]. The KeyId, for a shared secret,
SHOULD be an opaque identifier not derived from the actual key; an
integer counter, for example, is a good choice.
The signature time is the timestamp when the authentication code was
computed and added to the messages.
The KeyLink field in a MAC indicates how to negotiate keys and should
point towards the key exchange endpoint. The use of a key
negotiation algorithm is beyond the scope of this specification, and
a key negotiation algorithm is not required to use this field.
8.4. Signature
Signature-validation algorithms use public key cryptographic
algorithms such as RSA and the Elliptic Curve Digital Signature
Algorithm (ECDSA). This specification and the corresponding wire
encoding [RFC8609] only support three specific signature algorithms:
RSA-SHA256, EC-SECP-256K1, and EC-SECP-384R1. Other algorithms may
be added in through other documents or by using experimental or
vendor-validation algorithm types.
Mosko, et al. Experimental [Page 26]
RFC 8569 CCNx Semantics July 2019
A signature that is public key based requires a KeyId field and may
optionally carry a signature time, an embedded public key, an
embedded certificate, and a KeyLink. The signature time behaves as
normal to timestamp when the signature was created. We describe the
use and relationship of the other fields here.
It is not common to use embedded certificates, as they can be very
large and may have validity periods different than the validated
data. The preferred method is to use a KeyLink to the validating
certificate.
The KeyId field in the ValidationAlgorithm identifies the public key
used to verify the signature. It is similar to a Subject Key
Identifier from X.509 (Section 4.2.1.2 of [RFC5280]). We define the
KeyId to be a cryptographic hash of the public key in DER form. All
implementations MUST support the SHA-256 digest as the KeyId hash.
The use of other algorithms for the KeyId is allowed, and it will not
cause problems at a forwarder because the forwarder only matches the
digest algorithm and digest output and does not compute the digest
(see Section 9). It may cause issues with a Content Store, which
needs to verify the KeyId and PublicKey match (see Section 2.4.3);
though in this case, it only causes a cache miss and the Interest
would still be forwarded to the publisher. As long as the publisher
and consumers support the hash, data will validate.
As per Section 9, a forwarder only matches the KeyId to a KeyId
restriction. It does not need to look at the other fields such as
the public key, certificate, or KeyLink.
If a message carries multiples of the KeyId, public key, certificate,
or KeyLink, an endpoint (consumer, cache, or Content Store) MUST
ensure that any fields it uses are consistent. The KeyId MUST be the
corresponding hash of the embedded public key or certificate public
key. The hash function to use is the KeyId's HashType. If there is
both an embedded public key and a certificate, the public keys MUST
be the same.
A message SHOULD NOT have both a PublicKey and a KeyLink to a public
key, as that is redundant. It MAY have a PublicKey and a KeyLink to
a certificate.
A KeyLink in a first Content Object may point to a second Content
Object with a DER-encoded public key in the PublicKey field and an
optional DER-encoded X.509 certificate in the payload. The second
Content Object's KeyId MUST equal the first object's KeyId. The
second object's PublicKey field MUST be the public key corresponding
to the KeyId. That key must validate both the first and second
Mosko, et al. Experimental [Page 27]
RFC 8569 CCNx Semantics July 2019
object's signature. A DER-encoded X.509 certificate may be included
in the second object's payload and its embedded public key MUST match
the PublicKey. It must be issued by a trusted authority, preferably
specifying the valid namespace of the key in the distinguished name.
The second object MUST NOT have a KeyLink; we do not allow for
recursive key lookup.
9. Interest to Content Object Matching
A Content Object satisfies an Interest if and only if (a) the Content
Object name, if present, exactly matches the Interest name, (b) the
ValidationAlgorithm KeyId of the Content Object exactly equals the
Interest KeyId restriction, if present, and (c) the computed Content
Object Hash exactly equals the Interest Content Object Hash
restriction, if present.
The KeyId and KeyIdRestr use the Hash format (see Section 2.1). The
Hash format has an embedded HashType followed by the hash value.
When comparing a KeyId and KeyIdRestr, one compares both the HashType
and the value.
The matching rules are given by this predicate, which, if it
evaluates true, means the Content Object matches the Interest. Ni =
Name in the Interest (may not be empty), Ki = KeyIdRestr in the
Interest (may be empty), and Hi = ContentObjectHashRestr in the
Interest (may be empty). Likewise, No, Ko, and Ho are those
properties in the Content Object, where No and Ko may be empty; Ho
always exists (it is an intrinsic property of the Content Object).
For binary relations, we use "&" for AND and "|" for OR. We use "E"
for the EXISTS (not empty) operator and "!" for the NOT EXISTS
operator.
As a special case, if the Content Object Hash restriction in the
Interest specifies an unsupported hash algorithm, then no Content
Object can match the Interest, so the system should drop the Interest
and MAY send an Interest Return to the previous hop. In this case,
the predicate below will never get executed because the Interest is
never forwarded. If the system is using the optional behavior of
having a different system calculate the hash for it, then the system
may assume all hash functions are supported and leave it to the other
system to accept or reject the Interest.
(!No | (Ni=No)) & (!Ki | (Ki=Ko)) & (!Hi | (Hi=Ho)) & (E No | E Hi)
As one can see, there are two types of attributes one can match. The
first term depends on the existence of the attribute in the Content
Object while the next two terms depend on the existence of the
attribute in the Interest. The last term is the "Nameless Object"
Mosko, et al. Experimental [Page 28]
RFC 8569 CCNx Semantics July 2019
restriction that states that if a Content Object does not have a
Name, then it must match the Interest on at least the Hash
restriction.
If a Content Object does not carry the Content Object Hash as an
expressed field, it must be calculated in network to match against.
It is sufficient within an autonomous system to calculate a Content
Object Hash at a border router and carry it via trusted means within
the autonomous system. If a Content Object ValidationAlgorithm does
not have a KeyId, then the Content Object cannot match an Interest
with a KeyId restriction.
10. Interest Return
This section describes the process whereby a network element may
return an Interest message to a previous hop if there is an error
processing the Interest. The returned Interest may be further
processed at the previous hop or returned towards the Interest
origin. When a node returns an Interest, it indicates that the
previous hop should not expect a response from that node for the
Interest, i.e., there is no PIT entry left at the returning node.
The returned message maintains compatibility with the existing TLV
packet format (a fixed header, optional hop-by-hop headers, and the
CCNx Message body). The returned Interest packet is modified in only
two ways:
o The PacketType is set to Interest Return to indicate a Feedback
message.
o The ReturnCode is set to the appropriate value to signal the
reason for the return.
The specific encodings of the Interest Return are specified in
[RFC8609].
A forwarder is not required to send any Interest Return messages.
A forwarder is not required to process any received Interest Return
message. If a forwarder does not process Interest Return messages,
it SHOULD silently drop them.
The Interest Return message does not apply to a Content Object or any
other message type.
Mosko, et al. Experimental [Page 29]
RFC 8569 CCNx Semantics July 2019
An Interest Return message is a 1-hop message between peers. It is
not propagated multiple hops via the FIB. An intermediate node that
receives an Interest Return may take corrective actions or may
propagate its own Interest Return to previous hops as indicated in
the reverse path of a PIT entry.
10.1. Message Format
The Interest Return message looks exactly like the original Interest
message with the exception of the two modifications mentioned above.
The PacketType is set to indicate the message is an Interest Return,
and the reserved byte in the Interest header is used as a Return
Code. The numeric values for the PacketType and ReturnCodes are in
[RFC8609].
Mosko, et al. Experimental [Page 30]
RFC 8569 CCNx Semantics July 2019
10.2. ReturnCode Types
This section defines the Interest Return ReturnCode introduced in
this RFC. The numeric values used in the packet are defined in
[RFC8609].
+----------------------+--------------------------------------------+
| Name | Description |
+----------------------+--------------------------------------------+
| No Route (Section | The returning forwarder has no route to |
| 10.3.1) | the Interest name. |
| | |
| HopLimit Exceeded | The HopLimit has decremented to 0 and |
| (Section 10.3.2) | needs to forward the packet. |
| | |
| Interest MTU too | The Interest's MTU does not conform to the |
| large (Section | required minimum and would require |
| 10.3.3) | fragmentation. |
| | |
| No Resources | The node does not have the resources to |
| (Section 10.3.4) | process the Interest. |
| | |
| Path error (Section | There was a transmission error when |
| 10.3.5) | forwarding the Interest along a route (a |
| | transient error). |
| | |
| Prohibited (Section | An administrative setting prohibits |
| 10.3.6) | processing this Interest. |
| | |
| Congestion (Section | The Interest was dropped due to congestion |
| 10.3.7) | (a transient error). |
| | |
| Unsupported Content | The Interest was dropped because it |
| Object Hash | requested a Content Object Hash |
| Algorithm (Section | restriction using a hash algorithm that |
| 10.3.8) | cannot be computed. |
| | |
| Malformed Interest | The Interest was dropped because it did |
| (Section 10.3.9) | not correctly parse. |
+----------------------+--------------------------------------------+
Table 3: Interest Return Reason Codes
Mosko, et al. Experimental [Page 31]
RFC 8569 CCNx Semantics July 2019
10.3. Interest Return Protocol
This section describes the forwarder behavior for the various Reason
codes for Interest Return. A forwarder is not required to generate
any of the codes, but if it does, it MUST conform to this
specification.
If a forwarder receives an Interest Return, it SHOULD take these
standard corrective actions. A forwarder is allowed to ignore
Interest Return messages, in which case its PIT entry would go
through normal timeout processes.
o Verify that the Interest Return came from a next hop to which it
actually sent the Interest.
o If a PIT entry for the corresponding Interest does not exist, the
forwarder should ignore the Interest Return.
o If a PIT entry for the corresponding Interest does exist, the
forwarder MAY do one of the following:
* Try a different forwarding path, if one exists, and discard the
Interest Return, or
* Clear the PIT state and send an Interest Return along the
reverse path.
If a forwarder tries alternate routes, it MUST ensure that it does
not use the same path multiple times. For example, it could keep
track of which next hops it has tried and not reuse them.
If a forwarder tries an alternate route, it may receive a second
Interest Return, possibly of a different type than the first Interest
Return. For example, node A sends an Interest to node B, which sends
a No Route return. Node A then tries node C, which sends a
Prohibited Interest Return. Node A should choose what it thinks is
the appropriate code to send back to its previous hop.
If a forwarder tries an alternate route, it should decrement the
Interest Lifetime to account for the time spent thus far processing
the Interest.
10.3.1. No Route
If a forwarder receives an Interest for which it has no route, or for
which the only route is back towards the system that sent the
Interest, the forwarder SHOULD generate a "No Route" Interest Return
message.
Mosko, et al. Experimental [Page 32]
RFC 8569 CCNx Semantics July 2019
How a forwarder manages the FIB table when it receives a No Route
message is implementation dependent. In general, receiving a No
Route Interest Return should not cause a forwarder to remove a route.
The dynamic routing protocol that installed the route should correct
the route, or the administrator who created a static route should
correct the configuration. A forwarder could suppress using that
next hop for some period of time.
10.3.2. HopLimit Exceeded
A forwarder MAY choose to send HopLimit Exceeded messages when it
receives an Interest that must be forwarded off system and the
HopLimit is 0.
10.3.3. Interest MTU Too Large
If a forwarder receives an Interest whose MTU exceeds the prescribed
minimum, it MAY send an "Interest MTU Too Large" message, or it may
silently discard the Interest.
If a forwarder receives an "Interest MTU Too Large" response, it
SHOULD NOT try alternate paths. It SHOULD propagate the Interest
Return to its previous hops.
10.3.4. No Resources
If a forwarder receives an Interest and it cannot process the
Interest due to lack of resources, it MAY send an Interest Return. A
lack of resources could mean the PIT is too large or that there is
some other capacity limit.
10.3.5. Path Error
If a forwarder detects an error forwarding an Interest, such as over
a reliable link, it MAY send a Path-Error Interest Return indicating
that it was not able to send or repair a forwarding error.
10.3.6. Prohibited
A forwarder may have administrative policies, such as access control
lists (ACLs), that prohibit receiving or forwarding an Interest. If
a forwarder discards an Interest due to a policy, it MAY send a
Prohibited Interest Return to the previous hop. For example, if
there is an ACL that says "/example/private" can only come from
interface e0, but the forwarder receives one from e1, the forwarder
must have a way to return the Interest with an explanation.
Mosko, et al. Experimental [Page 33]
RFC 8569 CCNx Semantics July 2019
10.3.7. Congestion
If a forwarder discards an Interest due to congestion, it MAY send a
Congestion Interest Return to the previous hop.
10.3.8. Unsupported Content Object Hash Algorithm
If a Content Object Hash restriction specifies a hash algorithm the
forwarder cannot verify, the Interest should not be accepted and the
forwarder MAY send an Interest Return to the previous hop.
10.3.9. Malformed Interest
If a forwarder detects a structural or syntactical error in an
Interest, it SHOULD drop the Interest and MAY send an Interest Return
to the previous hop. This does not imply that any router must
validate the entire structure of an Interest.
11. IANA Considerations
This document has no IANA actions.
12. Security Considerations
The CCNx protocol is an L3 network protocol, which may also operate
as an overlay using other transports such as UDP or other tunnels.
It includes intrinsic support for message authentication via a
signature (e.g., RSA or elliptic curve) or message authentication
code (e.g., HMAC). In lieu of an authenticator, it may instead use a
message integrity check (e.g., SHA or CRC). CCNx does not specify an
encryption envelope; that function is left to a high-layer protocol
(e.g., [esic]).
The CCNx message format includes the ability to attach MICs (e.g.,
CRC32C), MACs (e.g., HMAC), and signatures (e.g., RSA or ECDSA) to
all packet types. This does not mean that it is a good idea to use
an arbitrary ValidationAlgorithm, nor to include computationally
expensive algorithms in Interest packets, as that could lead to
computational DoS attacks. Applications should use an explicit
protocol to guide their use of packet signatures. As a general
guideline, an application might use a MIC on an Interest to detect
unintentionally corrupted packets. If one wishes to secure an
Interest, one should consider using an encrypted wrapper and a
protocol that prevents replay attacks, especially if the Interest is
being used as an actuator. Simply using an authentication code or
signature does not make an Interest secure. There are several
examples in the literature on how to secure ICN-style messaging
[mobile] [ace].
Mosko, et al. Experimental [Page 34]
RFC 8569 CCNx Semantics July 2019
As an L3 protocol, this document does not describe how one arrives at
keys or how one trusts keys. The CCNx Content Object may include a
public key or certificate embedded in the object or may use the
KeyLink field to point to a public key or certificate that
authenticates the message. One key-exchange specification is CCNxKE
[ccnx-ke] [mobile], which is similar to the TLS 1.3 key exchange
except it is over the CCNx L3 messages. Trust is beyond the scope of
an L3 protocol and left to applications or application frameworks.
The combination of an ephemeral key exchange (e.g., CCNxKE [ccnx-ke])
and an encapsulating encryption (e.g., [esic]) provides the
equivalent of a TLS tunnel. Intermediate nodes may forward the
Interests and Content Objects but have no visibility inside. It also
completely hides the internal names in those used by the encryption
layer. This type of tunneling encryption is useful for content that
has little or no cacheability, as it can only be used by someone with
the ephemeral key. Short-term caching may help with lossy links or
mobility, but long-term caching is usually not of interest.
Broadcast encryption or proxy re-encryption may be useful for content
with multiple uses over time or many consumers. There is currently
no recommendation for this form of encryption.
The specific encoding of messages will have security implications.
[RFC8609] uses a type-length-value (TLV) encoding. We chose to
compromise between extensibility and unambiguous encodings of types
and lengths. Some TLV encodings use variable-length "T" and
variable-length "L" fields to accommodate a wide gamut of values
while trying to be byte efficient. Our TLV encoding uses a fixed-
length 2-byte "T" and 2-byte "L". Using a fixed-length "T" and "L"
field solves two problems. The first is aliases. If one is able to
encode the same value, such as %x02 and %x0002, in different byte
lengths, then one must decide if they mean the same thing, if they
are different, or if one is illegal. If they are different, then one
must always compare on the buffers, not the integer equivalents. If
one is illegal, then one must validate the TLV encoding, every field
of every packet at every hop. If they are the same, then one has the
second problem: how to specify packet filters. For example, if a
name has 6 name components, then there are 7 T's and 7 L's, each of
which might have up to 4 representations of the same value. That
would be 14 fields with 4 encodings each, or 1001 combinations. It
also means that one cannot compare, for example, a name via a memory
function as one needs to consider that any embedded "T" or "L" might
have a different format.
The Interest Return message has no authenticator from the previous
hop. Therefore, the payload of the Interest Return should only be
used locally to match an Interest. A node should never forward that
Mosko, et al. Experimental [Page 35]
RFC 8569 CCNx Semantics July 2019
Interest Payload as an Interest. It should also verify that it sent
the Interest in the Interest Return to that node and not allow anyone
to negate Interest messages.
Caching nodes must take caution when processing Content Objects. It
is essential that the Content Store obey the rules outlined in
Section 2.4.3 to avoid certain types of attacks. CCNx 1.0 has no
mechanism to work around an undesired result from the network (there
are no "excludes"), so if a cache becomes poisoned with bad content,
it might cause problems retrieving content. There are three types of
access to content from a Content Store: unrestricted, signature
restricted, and hash restricted. If an Interest has no restrictions,
then the requester is not particular about what they get back, so any
matching cached object is OK. In the hash-restricted case, the
requester is very specific about what they want and the Content Store
(and every forward hop) can easily verify that the content matches
the request. In the signature-restricted case (often used for
initial manifest discovery), the requester only knows the KeyId that
signed the content. It is this case that requires the closest
attention in the Content Store to avoid amplifying bad data. The
Content Store must only respond with a Content Object if it can
verify the signature; this means either the Content Object carries
the public key inside it or the Interest carries the public key in
addition to the KeyId. If that is not the case, then the Content
Store should treat the Interest as a cache miss and let an endpoint
respond.
A user-level cache could perform full signature verification by
fetching a public key or certificate according to the KeyLink. That
is not, however, a burden we wish to impose on the forwarder. A
user-level cache could also rely on out-of-band attestation, such as
the cache operator only inserting content that it knows has the
correct signature.
The CCNx grammar allows for hash-algorithm agility via the HashType.
It specifies a short list of acceptable hash algorithms that should
be implemented at each forwarder. Some hash values only apply to end
systems, so updating the hash algorithm does not affect forwarders;
they would simply match the buffer that includes the type-length-hash
buffer. Some fields, such as the ConObjHash, must be verified at
each hop, so a forwarder (or related system) must know the hash
algorithm; it could cause backward compatibility problems if the hash
type is updated. [RFC8609] is the authoritative source for per-
field-allowed hash types in that encoding.
A CCNx name uses binary matching whereas a URI uses a case-
insensitive hostname. Some systems may also use case-insensitive
matching of the URI path to a resource. An implication of this is
Mosko, et al. Experimental [Page 36]
RFC 8569 CCNx Semantics July 2019
that human-entered CCNx names will likely have case or non-ASCII
symbol mismatches unless one uses a consistent URI normalization to
the CCNx name. It also means that an entity that registers a CCNx
routable prefix, say "ccnx:/example.com", would need separate
registrations for simple variations like "ccnx:/Example.com". Unless
this is addressed in URI normalization and routing protocol
conventions, there could be phishing attacks.
For a more general introduction to ICN-related security concerns and
approaches, see [RFC7927] and [RFC7945].
13. References
13.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<
https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <
https://www.rfc-editor.org/info/rfc8174>.
13.2. Informative References
[ace] Shang, W., Yu, Y., Liang, T., Zhang, B., and L. Zhang,
"NDN-ACE: Access Control for Constrained Environments over
Named Data Networking", NDN Technical Report NDN-0036,
December 2015, <
http://new.named-data.net/
wp-content/uploads/2015/12/ndn-0036-1-ndn-ace.pdf>.
[befrags] Mosko, M. and C. Tschudin, "ICN "Begin-End" Hop by Hop
Fragmentation", Work in Progress, draft-mosko-icnrg-
beginendfragment-02, December 2016.
[ccn-lite] Tschudin, C., et al., "CCN-lite", University of Basel,
2011-2019, <
http://ccn-lite.net>.
[ccnx-ke] Mosko, M., Uzun, E., and C. Wood, "CCNx Key Exchange
Protocol Version 1.0", Work in Progress, draft-wood-icnrg-
ccnxkeyexchange-02, March 2017.
[ccnx-registry]
IANA, "Content-Centric Networking (CCNx)",
<
https://www.iana.org/assignments/ccnx>.
Mosko, et al. Experimental [Page 37]
RFC 8569 CCNx Semantics July 2019
[ccnx-uri] Mosko, M. and C. Wood, "The CCNx URI Scheme", Work in
Progress, draft-mosko-icnrg-ccnxurischeme-01, April 2016.
[chunking] Mosko, M., "CCNx Content Object Chunking", Work in
Progress, draft-mosko-icnrg-ccnxchunking-02, June 2016.
[cicn] FD.io, "Community ICN (CICN)", February 2017,
<
https://wiki.fd.io/index.php?title=Cicn&oldid=7191>.
[dart] Garcia-Luna-Aceves, J. and M. Mirzazad-Barijough, "A
Light-Weight Forwarding Plane for Content-Centric
Networks", International Conference on Computing,
Networking, and Communications (ICNC),
DOI 10.1109/ICCNC.2016.7440637, February 2016,
<
https://arxiv.org/pdf/1603.06044.pdf>.
[eprise-numbers]
IANA, "IANA Private Enterprise Numbers",
<
https://www.iana.org/assignments/enterprise-numbers>.
[esic] Mosko, M. and C. Wood, "Encrypted Sessions In CCNx
(ESIC)", Work in Progress, draft-wood-icnrg-esic-01,
September 2017.
[flic] Tschudin, C. and C. Wood, "File-Like ICN Collection
(FLIC)", Work in Progress, draft-tschudin-icnrg-flic-03,
March 2017.
[mobile] Mosko, M., Uzun, E., and C. Wood, "Mobile Sessions in
Content-Centric Networks", IFIP Networking Conference
(IFIP Networking) and Workshops,
DOI 10.23919/IFIPNetworking.2017.8264861, June 2017,
<
https://dl.ifip.org/db/conf/networking/
networking2017/1570334964.pdf>.
[ndn] UCLA, "Named Data Networking", 2019,
<
https://www.named-data.net>.
[nnc] Jacobson, V., Smetters, D., Thornton, J., Plass, M.,
Briggs, N., and R. Braynard, "Networking Named Content",
Proceedings of the 5th International Conference on
Emerging Networking Experiments and Technologies,
DOI 10.1145/1658939.1658941, December 2009,
<
https://dx.doi.org/10.1145/1658939.1658941>.
Mosko, et al. Experimental [Page 38]
RFC 8569 CCNx Semantics July 2019
[RFC5234] Crocker, D., Ed. and P. Overell, "Augmented BNF for Syntax
Specifications: ABNF", STD 68, RFC 5234,
DOI 10.17487/RFC5234, January 2008,
<
https://www.rfc-editor.org/info/rfc5234>.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List
(CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
<
https://www.rfc-editor.org/info/rfc5280>.
[RFC7927] Kutscher, D., Ed., Eum, S., Pentikousis, K., Psaras, I.,
Corujo, D., Saucez, D., Schmidt, T., and M. Waehlisch,
"Information-Centric Networking (ICN) Research
Challenges", RFC 7927, DOI 10.17487/RFC7927, July 2016,
<
https://www.rfc-editor.org/info/rfc7927>.
[RFC7945] Pentikousis, K., Ed., Ohlman, B., Davies, E., Spirou, S.,
and G. Boggia, "Information-Centric Networking: Evaluation
and Security Considerations", RFC 7945,
DOI 10.17487/RFC7945, September 2016,
<
https://www.rfc-editor.org/info/rfc7945>.
[RFC8609] Mosko, M., Solis, I., and C. Wood, "Content-Centric
Networking (CCNx) Messages in TLV Format", RFC 8609,
DOI 10.17487/RFC8609, July 2019,
<
https://www.rfc-editor.org/info/rfc8609>.
[selectors]
Mosko, M., "CCNx Selector Based Discovery", Work in
Progress, draft-mosko-icnrg-selectors-01, May 2019.
[terminology]
Wissingh, B., Wood, C., Afanasyev, A., Zhang, L., Oran,
D., and C. Tschudin, "Information-Centric Networking
(ICN): CCN and NDN Terminology", Work in Progress,
draft-irtf-icnrg-terminology-04, June 2019.
[trust] Tschudin, C., Uzun, E., and C. Wood, "Trust in
Information-Centric Networking: From Theory to Practice",
25th International Conference on Computer Communication
and Networks (ICCCN), DOI 10.1109/ICCCN.2016.7568589,
August 2016, <
https://doi.org/10.1109/ICCCN.2016.7568589>.
Mosko, et al. Experimental [Page 39]
RFC 8569 CCNx Semantics July 2019
Authors' Addresses
Marc Mosko
PARC, Inc.
Palo Alto, California 94304
United States of America
Phone: +01 650-812-4405
Email:
[email protected]
Ignacio Solis
LinkedIn
Mountain View, California 94043
United States of America
Email:
[email protected]
Christopher A. Wood
University of California Irvine
Irvine, California 92697
United States of America
Phone: +01 315-806-5939
Email:
[email protected]
Mosko, et al. Experimental [Page 40]
