Internet Engineering Task Force (IETF) V. Hilt

Internet Engineering Task Force (IETF) V. Hilt
Request for Comments: 6796 Bell Labs/Alcatel-Lucent
Category: Standards Track G. Camarillo
ISSN: 2070-1721 Ericsson
J. Rosenberg
jdrosen.net
D. Worley
Ariadne
December 2012

A User Agent Profile Data Set for Media Policy

Abstract

This specification defines an XML document format to describe the
media properties of Session Initiation Protocol (SIP) sessions.
Examples for media properties are the codecs or media types used in
the session. This document also defines an XML document format to
describe policies that limit the media properties of SIP sessions.

Status of This Memo

This is an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.

Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6796.

Hilt, et al. Standards Track [Page 1]

RFC 6796 Media Policy Data Set December 2012

Copyright Notice

Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.

Table of Contents

1. Introduction ....................................................4
2. Terminology .....................................................5
3. Media Policy Data Set Format ....................................5
3.1. Namespace and Media Type ...................................5
3.2. Extensibility ..............................................5
3.3. Attributes .................................................6
3.3.1. The 'visibility' Attribute ..........................6
3.3.2. The 'direction' Attributes ..........................6
3.3.3. The 'q' Attribute ...................................6
3.3.4. The 'media-type' Attribute ..........................7
3.3.5. The 'label' Attribute ...............................7
3.3.6. The 'enabled' Attribute .............................7
4. Session Info Documents ..........................................7
4.1. Mapping between SDP and Session Info Documents .............8
4.2. The <session-info> Element ................................10
4.3. The <streams> Element .....................................10
4.3.1. The <stream> Element ...............................10
4.4. The <media-intermediaries> Element ........................11
4.4.1. The <fixed-intermediary> Element ...................12
4.4.2. The <turn-intermediary> Element ....................13
4.4.3. The <msrp-intermediary> Element ....................13
5. Session Policy Documents .......................................14
5.1. Merging Session Policies ..................................14
5.1.1. Single Value Selection .............................14
5.1.2. Merging Sets .......................................15
5.1.3. Local Policy Server Selection ......................16
5.2. The <session-policy> Element ..............................16
5.3. The <media-types-allowed> Element .........................16
5.4. The <media-types-excluded> Element ........................17
5.5. The <codecs-allowed> Element ..............................17
5.6. The <codecs-excluded> Element .............................18

Hilt, et al. Standards Track [Page 2]

RFC 6796 Media Policy Data Set December 2012

5.7. The <local-ports> Element .................................18
6. Common Media Policy Data Set Elements ..........................19
6.1. The <media-type> Element ..................................19
6.2. The <codec> Element .......................................19
6.2.1. The <media-type-subtype> Element ...................20
6.2.2. The <mime-parameter> Element .......................20
6.3. The <max-bw> Element ......................................20
6.4. The <max-session-bw> Element ..............................21
6.5. The <max-stream-bw> Element ...............................21
6.6. The <qos-dscp> Element ....................................22
6.7. The <context> Element .....................................23
6.7.1. The <policy-server-URI> Element ....................23
6.7.2. The <contact> Element ..............................23
6.7.3. The <info> Element .................................23
6.7.4. The <request-URI> Element ..........................23
6.7.5. The <token> Element ................................24
6.8. Other Session Properties ..................................24
7. Examples .......................................................25
7.1. Session Policy Documents ..................................25
7.2. Session Information Documents .............................25
7.2.1. Example 1 ..........................................25
7.2.2. Example 2 ..........................................26
8. RELAX NG Definition ............................................29
9. Security Considerations ........................................37
10. IANA Considerations ...........................................38
10.1. Media Type Registration ..................................38
10.2. RELAX NG Schema Registration .............................39
10.3. URN Sub-Namespace Registration ...........................39
11. References ....................................................40
11.1. Normative References .....................................40
11.2. Informative References ...................................41
Appendix A. Acknowledgements ......................................42

Hilt, et al. Standards Track [Page 3]

RFC 6796 Media Policy Data Set December 2012

1. Introduction

Within the Session Initiation Protocol (SIP) [RFC3261], "A Framework
for Session Initiation Protocol (SIP) User Agent Profile Delivery"
[RFC6080] and "A Framework for SIP Session Policies" [RFC6794] define
mechanisms to convey session policies and configuration information
from a network server to a user agent. An important piece of the
information conveyed to the user agent relates to the media
properties of the SIP sessions set up by the user agent. Examples
for these media properties are the codecs and media types used, the
media-intermediaries to be traversed, or the maximum bandwidth
available for media streams.

This specification defines a document format for media properties of
SIP sessions: the Media Policy Data Set Format (MPDF). This format
can be used in two ways. First, it can be used to describe the
properties of a given SIP session (e.g., the media types and codecs
used). These MPDF documents are called session info documents and
they are usually created based on the session description of a
session. Second, the MPDF format can be used to define policies for
SIP sessions in a session policy document. A session policy document
defines properties for a session (e.g., the media types allowed in a
session), independent of a specific session description.

If used with "A Framework for SIP Session Policies" [RFC6794],
session info documents are used in conjunction with session-specific
policies. A session info document is created by a user agent (UA)
based on the current session description and submitted to the policy
server. The policy server examines the session info document,
modifies it if necessary (e.g., by removing video streams if video is
not permitted), and returns the possibly modified session info
document to the UA. Session policy documents, on the other hand, are
used to describe session-independent policies that can be submitted
to the UA independent of a specific session.

The two types of MPDF documents, session information and session
policy documents, share the same set of XML elements to describe
session properties. Since these elements are used in different
contexts for session info and session policy documents, two different
root elements exist for the two document types: <session-info> is the
root element for session information documents and <session-policy>
is the root element for session policy documents.

A user agent can receive multiple session policy documents from
different sources. This can lead to a situation in which the user
agent needs to apply multiple session policy documents to the same
session. This standard specifies merging rules for those XML
elements that can be present in session policy documents. It should

Hilt, et al. Standards Track [Page 4]

RFC 6796 Media Policy Data Set December 2012

be noted that these merging rules are part of the semantics of a
session policy XML element. User agents implement the merging rules
as part of implementing the element semantics. As a consequence, it
is not possible to build an entity that can mechanically merge two
session policy documents without understanding the semantics of all
elements in the input documents.

Merging rules are not needed for elements of session information
documents since they are created by one source and describe a
specific session.

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].

3. Media Policy Data Set Format

This section discusses fundamental properties of the Media Policy
Data Set Format (MPDF).

3.1. Namespace and Media Type

The MPDF format is based on XML [W3C.REC-xml-20081126]. An MPDF
document MUST be well-formed and MUST be valid according to schemas,
including extension schemas, available to the validator and
applicable to the XML document. MPDF documents MUST be based on XML
1.0 and MUST be encoded using UTF-8.

MPDF makes use of XML namespaces [W3C.REC-xml-names-19990114]. The
namespace URIs for elements defined in this specification are URNs
[RFC2141], using the namespace identifier 'ietf' defined by [RFC2648]
and extended by [RFC3688]. The namespace URN for the MPDF schema is:

urn:ietf:params:xml:ns:mediadataset

The media type for the Media Policy Data Set Format is:

application/media-policy-dataset+xml

3.2. Extensibility

The MPDF format can be extended using XML extension mechanisms if
additional media properties are needed. In particular, elements from
different XML namespaces MAY be present within a MPDF document for
the purposes of extensibility; elements or attributes from unknown
namespaces MUST be ignored.

Hilt, et al. Standards Track [Page 5]

RFC 6796 Media Policy Data Set December 2012

3.3. Attributes

The following attributes can be used with elements of the MPDF
format. The specification of each MPDF element lists which of these
attributes can be used. If an element bears an attribute that may
not be used with it, the user agent MUST ignore the attribute.

3.3.1. The 'visibility' Attribute

The attribute 'visibility' specifies whether or not the user agent is
advised to display the property value to the user. This is used to
hide setting values that the administrator may not want the user to
see or know. The 'visibility' attribute has two possible values:

o visible: specifies that display of the property value is not
restricted. This is the default value of the attribute if it is
not specified.

o hidden: Specifies that the user agent is advised not to display
the property value. Display of the property value may be allowed
using special administrative interfaces, but it is not appropriate
for the ordinary user.

3.3.2. The 'direction' Attributes

Some properties are unidirectional and only apply to messages or data
streams transmitted into one direction. For example, a property for
media streams can be restricted to outgoing media streams only.
Unidirectional properties can be expressed by adding a 'direction'
attribute to the respective element.

The 'direction' attribute can have the following values:

o recvonly: the property only applies to incoming streams.

o sendonly: the property only applies to outgoing streams.

o sendrecv: the property applies to streams in both directions.
This is the default value that is used if the 'direction'
attribute is omitted.

3.3.3. The 'q' Attribute

It is possible to express a preference for a certain value relative
to the other values within a set of multiple values that are allowed
within a property. For example, it is possible to express that the
codecs G.711 and G.729 are allowed, but G.711 is preferred.
Preferences are to be expressed by adding a 'q' attribute to a

Hilt, et al. Standards Track [Page 6]

RFC 6796 Media Policy Data Set December 2012

property element. The 'q' attribute is only allowed in elements that
specify allowed values (as opposed to elements that specify forbidden
values).

The value of the 'q' attribute is a decimal number within the range
of 0 to 1, inclusive, with two or fewer decimal places. An element
with a higher 'q' value is preferred over one with a lower 'q' value.

3.3.4. The 'media-type' Attribute

The media-type attribute is used to define that an element only
applies to streams of a certain media type, as defined in Section
8.2.1 of [RFC4566]. For example, it may only apply to audio streams.
The value of the 'media-type' attribute MUST be the media type, such
as audio, video, text, or application.

3.3.5. The 'label' Attribute

The label attribute is used to identify a specific media stream. The
value of the label attribute is a token, whose syntax is defined in
[RFC4574]. The token can be chosen freely; however, it MUST be
unique among all <stream> elements in a session-info document.

3.3.6. The 'enabled' Attribute

The 'enabled' attribute specifies whether or not the user agent is
allowed to establish a media stream. This boolean attribute has two
possible values:

o yes: specifies that the media stream can be established. This is
the default value of the attribute if it is not specified.

o no: specifies that the user agent MUST NOT establish the media
stream.

4. Session Info Documents

Session info documents describe key properties of a SIP session such
as the media streams used in the session. Session info documents are
typically created based on a session description expressed using
Session Description Protocol (SDP) [RFC4566] or an SDP offer/answer
pair [RFC3264].

Session info documents can be used for session-specific policies
[RFC6794]. In this usage, a UA creates a session info document based
on its session description(s) and sends this document to the policy
server. The policy server modifies this document according to the
policies that apply to the described session and returns a version of

Hilt, et al. Standards Track [Page 7]

RFC 6796 Media Policy Data Set December 2012

the session info document that is compliant to the policies. For
example, if video streams are not permissible under current policies
and the UA submits a session info document that contains a video
stream, the policy server will disable (i.e., enabled="no") the video
stream in the session info document that it returns to the UA.

Session info documents use the <session-info> root element. They use
elements described in this section and common elements described in
Section 6.

Elements that are only present in session info documents do not
require merging rules. If used in the context of session-specific
policies, session info documents are sent to one policy server at a
time only; therefore, a UA does not need to merge multiple session
info documents into one. A policy server needs to modify a session
info document it has received according to its policies. The
modification of session info documents is determined by the local
policies of the policy server and is, thus, outside the scope of this
standard.

A policy server can completely reject a session by returning a
session info document with an empty <session-info> element:

<session-info></session-info>

4.1. Mapping between SDP and Session Info Documents

This section specifies how to map information in a session
description or an SDP offer/answer pair [RFC3264] to session info
documents. It also specifies how to map a session info document into
a session description. Note that these mapping rules do not include
rules for all elements that need to be present in a session info
document or in a session description. That is, some of those
elements are generated following their associated general rules
(e.g., the general rules to generate SDP "v=" and "t=" lines).

A UA with a session description that needs to create a session info
document uses the data in the session description and maps it
following the rules below. A UA with an SDP offer/answer pair that
needs to create a session info document uses the data that has been
agreed in the offer/answer exchange.

A UA MUST create a separate <stream> element for each "m=" line in a
session description or SDP offer/answer pair; the order of the
<stream> elements corresponds to the order of the "m=" lines. For a
session description, the UA MUST insert the media type from the "m="
line into a <media-type> element and MUST create a <codec> element
for each codec listed in the "m=" line. For an SDP offer/answer

Hilt, et al. Standards Track [Page 8]

RFC 6796 Media Policy Data Set December 2012

pair, the UA MUST insert a <codec> element for each of the codecs
that were agreed upon for the particular stream in the offer/answer
exchange. The <codec> elements MUST have 'q' attributes with values
that decrease with the order the codecs are given in the "m=" line.
(Other than the ordering restriction, the particular values used are
not specified by this document.)

The UA MUST create a <local-host-port> element for each stream using
the port taken from the "m=" line and the address from the
corresponding "c=" line of the local session description. The UA
SHOULD create a <remote-host-port> element using the port and address
from the "m=" and "c=" lines for the same stream taken from the
remote session description if this session description is available.
(The local SDP is the one sent by the UA; the remote SDP is the one
received from the remote UA.)

The <remote-host-port> contains information that may be considered
sensitive from a privacy standpoint. A UA configured not to
disclose that information would not include the <remote-host-port>
element in its session info documents.

The numeric value in a "b=CT:..." attribute in a session description
is used to set the content of a <max-bw> element with the direction
attribute value corresponding to which SDP contains the "b="
attribute.

The numeric value in a "b=AS:..." attribute at the session level in a
session description is used to set the content of a <max-session-bw>
element with the direction attribute value corresponding to the SDP
which contains the "b=" attribute.

The numeric value in a "b=AS:..." attribute at the media level in a
media description is used to set the content of a <max-stream-bw>
element child of the appropriate <stream> element, with the direction
attribute value corresponding to the SDP which contains the "b="
attribute.

An "a=label:..." attribute [RFC4574] is used to set the 'label'
attribute of the appropriate <stream> element.

The mapping from a session info document to a session description
follows the same rules in the reverse direction.

For any particular "m=" line, the codecs MUST be listed in decreasing
order of the values of the 'q' attributes of the corresponding
<codec> elements.

Hilt, et al. Standards Track [Page 9]

RFC 6796 Media Policy Data Set December 2012

4.2. The <session-info> Element

The <session-info> element describes the properties of a specific SIP
session. The <session-info> element MAY contain the optional
<context> and <streams> elements, and multiple (including zero)
<max-bw>, <max-session-bw>, <max-stream-bw>, <media-intermediaries>,
and <qos-dscp> elements, as well as elements from other namespaces.

4.3. The <streams> Element

The <streams> element is a container that is used to describe the
media streams used in a session. A <streams> element contains zero
or more <stream> elements. Each <stream> element describes the
properties (e.g., media type, codecs, and IP addresses and ports) of
a single media stream.

4.3.1. The <stream> Element

The <stream> element describes a specific media stream. It contains
the media type, codecs, and the hostname(s) or IP address(es) and
port(s) of this stream.

The hostname(s) or IP address(es) and port number(s) of a stream
correspond to the ones listed in the session description(s). A UA
that generates a <stream> element MUST insert the hostname/port found
in the local session description for this media stream into the
local-host-port element. The UA SHOULD insert the hostname/port of
the remote session description into the <remote-host-port> element,
if the remote session description is available to the UA. If not,
the UA generates a stream element that only contains the <local-host-
port> element.

This element MAY have the direction, label, and enabled attributes
(see Section 3.3).

The 'label' attribute is used to identify a specific media stream.
The value of the label attribute is a token that is unique among all
<stream> elements in a session-info document and whose syntax is
defined in [RFC4566].

The 'enabled' attribute specifies whether or not the user agent is
allowed to establish a media stream.

The <stream> element MUST contain one <media-type> element, one or
more <codec> elements and one <local-host-port> element. The
<stream> element MUST contain zero or one <remote-host-port>
elements.

Hilt, et al. Standards Track [Page 10]

RFC 6796 Media Policy Data Set December 2012

4.3.1.1. The <local-host-port> Element

The <local-host-port> element contains the hostname or IP address and
the receiving port number of the media stream in the local session
description. The hostname or IP address is separated from the port
by a ":". An example is: "host.example.com:49562".

The hostname or IP address of element is found in the "c=" element
for the stream in the local session description. The port number is
found in the "m=" element.

4.3.1.2. The <remote-host-port> Element

The <remote-host-port> element is structured exactly as the <local-
host-port> element. However, it identifies the hostname or IP
address and receiving port number of the media stream in the remote
session description.

4.4. The <media-intermediaries> Element

The <media-intermediaries> element expresses a policy for routing
media streams through media intermediaries. The purpose of the
<media-intermediaries> element is to tell the UA to send media
streams through a chain of media intermediaries. The manner in which
the UA arranges for a media stream to pass through the intermediaries
depends on the type of intermediary.

The <media-intermediaries> element is a container that lists all
media intermediaries to be traversed. Media intermediaries should be
traversed in the order in which they appear in this list. The
topmost entry should be traversed first, the last entry should be
traversed last.

Different types of intermediaries exist. These intermediaries are
not necessarily interoperable and it may not be possible to chain
them in an arbitrary order. A <media-intermediaries> element SHOULD
therefore only contain intermediary elements of the same type.

This element MAY have the 'direction' attribute (see Section 3.3).

Multiple <media-intermediaries> elements MUST NOT be present in a
container unless each applies to a different set of streams (e.g.,
one <media-intermediaries> element for incoming and one for outgoing
streams). The <media-intermediaries> element MUST contain one or
more elements defining a specific media intermediary, such as <fixed-
intermediary> or <turn-intermediary>.

Hilt, et al. Standards Track [Page 11]

RFC 6796 Media Policy Data Set December 2012

Note: it is not intended that the <media-intermediaries> element
replace connectivity discovery mechanisms such as Interactive
Connectivity Establishment (ICE). Instead of finding media relays
that provide connectivity, this element defines a policy for media
intermediaries that should be traversed. The set of
intermediaries defined in the <media-intermediaries> element and
the ones discovered through ICE may overlap but don't have to.

4.4.1. The <fixed-intermediary> Element

A fixed intermediary relies on pre-configured forwarding rules. The
user agent simply sends media to the first media intermediary listed.
It can assume that this media intermediary has been pre-configured
with a forwarding rule for the media stream and knows where to
forward the packets. The configuration of forwarding rules in the
intermediary must be done through other means.

The contents of a <fixed-intermediary> element MUST be echoed to all
policy servers that provide policies for a session. That is, if
multiple policy servers provide policies for the same session, this
element needs to be forwarded to all of them, possibly in a second
round of session-specific policy subscriptions as described in
[RFC6794] in the "Contacting the Policy Server" section.

The <fixed-intermediary> element MUST contain one <int-host-port>
element and MAY contain multiple optional <int-addl-port> elements.

4.4.1.1. The <int-host-port> Element

The <int-host-port> element contains the hostname or IP address and
port number of a media intermediary. The UA uses this hostname/IP
address and port to send its media streams to the intermediary. The
hostname or IP address is separated from the port by a ":".

If a protocol uses multiple subsequent ports (e.g., RTP), the lowest
port number SHOULD be included in the <int-host-port> element. All
additional port numbers SHOULD be identified in <int-addl-port>
elements.

4.4.1.2. The <int-addl-port> Element

If a protocol uses multiple subsequent ports (e.g., RTP), the lowest
port number SHOULD be included in the <int-host-port> element. All
additional port numbers SHOULD be identified in <int-addl-port>
elements.

Hilt, et al. Standards Track [Page 12]

RFC 6796 Media Policy Data Set December 2012

4.4.2. The <turn-intermediary> Element

The Traversal Using Relays around NAT (TURN) [RFC5766] protocol
provides a mechanism for inserting a relay into the media path.
Although the main purpose of TURN is NAT traversal, it is possible
for a TURN relay to perform other media intermediary functionalities.
The user agent establishes a binding on the TURN server and uses this
binding to transmit and receive media.

The <turn-intermediary> element MUST contain one <int-host-port>
element and MAY contain multiple optional <int-addl-port> elements
and zero or one each of the <shared-secret>, <user>, and <transport>
elements. If no <transport> element is present, UDP is assumed.

4.4.2.1. The <shared-secret> Element

The <shared-secret> element contains the shared secret needed to
authenticate at the media intermediary.

4.4.2.2. The <user> Element

The <user> element contains the user ID needed to authenticate to the
media intermediary.

4.4.2.3. The <transport> Element

The <transport> element contains the name of the transport to be used
for communicating with the TURN server. This document defines the
values "tcp" and "udp" for use in the <transport> element. Other
specifications may define additional values.

4.4.3. The <msrp-intermediary> Element

The Message Session Relay Protocol (MSRP) Relay Extensions [RFC4976]
define a means for incorporating relays into the media path of an
MSRP [RFC4975] session. MSRP is explicitly designed for a variety of
purposes, including policy enforcement.

The <msrp-intermediary> element MUST contain one <msrp-uri> element,
and may contain zero or one of each of the <shared-secret> and <user>
elements.

Hilt, et al. Standards Track [Page 13]

RFC 6796 Media Policy Data Set December 2012

4.4.3.1. The <msrp-uri> Element

The <msrp-uri> element contains a URI that indicates the MSRP server
to use for an intermediary. The UA uses this URI to authenticate
with the MSRP relay, and then uses the URI it learns through that
authentication process for any MSRP media it sends or receives. The
URIs in the <msrp-uri> element MUST have a scheme of "msrps:".

5. Session Policy Documents

Session policy documents describe policies for SIP sessions. Session
policy documents are independent of any specific session description
and express general policies for SIP sessions. A session policy
document is used to determine if a SIP session is policy-conformant
and can be used to modify the session, if needed, to conform to the
described policies.

Session policy documents can be used to encode session-independent
policies [RFC6794]. In this usage, a policy server creates a session
policy document and passes this document to a UA. The UA applies the
policies defined to the SIP sessions it is establishing. For
example, a session policy document can contain an element that
prohibits the use of video. To set up a session that is compliant to
this policy, a UA does not include the video media type in its SDP
offer or answer.

Session policy documents use the <session-policy> root element. They
use elements described in this section and common elements described
in Section 6.

5.1. Merging Session Policies

A UA may receive session policy documents from multiple sources;
multiple session policy documents can be merged into a single session
policy document that expresses the logical AND of the policies.

5.1.1. Single Value Selection

Properties that have a single value (e.g., the maximum bandwidth
allowed) require that a common value be determined for this property
during the merging process. The merging rules for determining this
value need to be defined individually for each element in the schema
definition (e.g., select the lowest maximum bandwidth).

Hilt, et al. Standards Track [Page 14]

RFC 6796 Media Policy Data Set December 2012

5.1.2. Merging Sets

The <media-types-allowed>, <media-types-excluded>, <codecs-allowed>
and <codecs-excluded> elements are containers that hold a set of
media-type/codec elements. The values defined in these containers
MUST be merged to determine the set of media types/codecs that are
permissible in a session. Note that for a particular codec, the
<mime-parameter> element (see Section 6.2.2) allows identifying a
particular encoding or profile of the codec. Therefore, when the
<mime-parameter> element is present, what is allowed or excluded is
the particular encoding or profile. Other encodings or profiles of
the same codec are unaffected.

To merge the media-types-* and codecs-* containers, a UA MUST apply
all containers it has received one after the other to the set of
media types/codecs it supports. After applying media-types-*/
codecs-* elements, the UA has the list of media types/codecs that are
allowed in a session. The containers MAY be applied in any order.
However, each time a container is applied to the set of media types/
codecs allowed, this set MUST stay the same or be reduced. Media
types/codecs cannot be added during this process.

The following example illustrates the merging process for two data
sets. In this example, the UA supports the following set of audio
codecs: PCMA, PCMU, and G729. After applying session policy document
1, the UA removes PCMA as it is disallowed by this policy. The
remaining set of codecs is PCMU and G729. Session policy document 2
disallows all codecs that are not listed. After applying this
policy, the set of codecs allowed is G729.

Session Policy Document 1:
<codecs-excluded>
<codec><media-type-subtype>audio/PCMA</media-type-subtype></codec>
</codecs-excluded>

Session Policy Document 2:
<codecs-allowed>
<codec><media-type-subtype>audio/PCMA</media-type-subtype></codec>
<codec><media-type-subtype>audio/G729</media-type-subtype></codec>
</codecs-allowed>

It is possible that two session policy documents define non-
overlapping sets of allowed media types or codecs. The resulting
merged set would be empty, which is illegal according to the schema
definition of the media-type/codec elements. This constitutes a
conflict that cannot be resolved automatically. If these properties
are enforced by both networks, the UA will not be able to set up a
session.

Hilt, et al. Standards Track [Page 15]

RFC 6796 Media Policy Data Set December 2012

The combined set of media types/codecs MUST again be valid and well-
formed according to the schema definitions. A conflict occurs if the
combined property set is not a well-formed document after the merging
process is completed.

5.1.3. Local Policy Server Selection

Some properties require that only values from the local policy server
are used. The local policy server is the policy server that is in
the local domain of the user agent.

If policy documents are delivered through the configuration framework
[RFC6080], the value received through a subscription using the
"local-network" profile-type SHOULD used. Values received through
other profile-type subscriptions SHOULD be discarded.

If policy documents are delivered through the session-specific policy
mechanism [RFC6794] the value received from the policy server
identified by the Local Policy Server URI SHOULD used. Values
received from other policy servers SHOULD be discarded.

5.2. The <session-policy> Element

The <session-policy> element describes a policy that applies to SIP
sessions. The <session-policy> element MAY contain the optional
<context> and <local-ports> elements and multiple (including zero)
<media-types-allowed>, <media-types-excluded>, <codecs-allowed>,
<codecs-excluded>, <max-bw>, <max-session-bw>, <max-stream-bw>, and
<qos-dscp> elements as well as elements from other namespaces.

5.3. The <media-types-allowed> Element

The <media-types-allowed> element is a container that is used to
define the set of media types (e.g., audio, video) that are allowed
in a session. All media types that are not listed in this container
are not permitted in a session. A specific media type is allowed by
adding the corresponding <media-type> element to this container.

This element MAY have the 'direction' and 'visibility' attributes
(see Section 3.3).

Multiple <media-types-allowed> elements MUST NOT be present in a
container element unless each applies to a different set of streams
(e.g., one <media-types-allowed> element for incoming and one for
outgoing streams). The <media-types-allowed> element MUST contain
zero or more <media-type> elements.

Hilt, et al. Standards Track [Page 16]

RFC 6796 Media Policy Data Set December 2012

A <media-types-allowed> element MUST NOT be used in a container that
contains a <media-types-excluded> element. The absence of both
elements in a container indicates no restrictions regarding media
types.

Merging of session-policy documents: <media-types-allowed> containers
are merged as described in "Merging Sets" Section 5.1.2.

5.4. The <media-types-excluded> Element

The <media-types-excluded> element is a container that is used to
define the set of media types (e.g., audio, video) that are not
permitted in a session. All media types that are not listed in this
container are allowed and can be used in a session. A specific media
type is excluded from a session by adding the corresponding <media-
type> element to this container.

This element MAY have the 'direction' and 'visibility' attributes
(see Section 3.3).

Multiple <media-types-excluded> elements MUST NOT be present in a
container element unless each applies to a different set of streams
(e.g., one <media-types-excluded> element for incoming and one for
outgoing streams). The <media-types-excluded> element MUST contain
zero or more <media-type> elements.

A <media-types-excluded> element MUST NOT be used in a container that
contains a <media-types-allowed> element. The absence of both
elements in a container indicates no restrictions regarding media
types.

Merging of session-policy documents: <media-types-excluded>
containers are merged as described in "Merging Sets" Section 5.1.2.

5.5. The <codecs-allowed> Element

The <codecs-allowed> element is a container that is used to define
the set of codecs that may be used in a session. All codecs not
listed in the <codecs-allowed> element are disallowed and MUST NOT be
used in a session. A policy MUST allow the use of at least one codec
per media type. A specific codec is allowed by adding the
corresponding <codec> element to this container.

The <codecs-allowed> element MAY have the 'direction' and
'visibility' attributes (see Section 3.3).

Hilt, et al. Standards Track [Page 17]

RFC 6796 Media Policy Data Set December 2012

Multiple <codecs-allowed> elements MUST NOT be present in a container
element unless each applies to a different set of streams (e.g., one
<codecs-allowed> element for incoming and one for outgoing streams).
The <codecs-allowed> element MUST contain zero or more <codec>
elements.

A <codecs-allowed> element MUST NOT be used in a container that
contains a <codecs-excluded> element. The absence of both elements
in a container indicates no restrictions regarding codecs.

Merging of session-policy documents: <codecs-allowed> containers are
merged as described in "Merging Sets" Section 5.1.2.

5.6. The <codecs-excluded> Element

The <codecs-excluded> element is a container that is used to define
the set of codecs that are disallowed in a session. All codecs not
listed in the <codecs-excluded> element are permitted and MAY be used
in a session. A specific codec is disallowed by adding the
corresponding <codec> element to this container.

The <codecs-excluded> element MAY have the 'direction' and
'visibility' attributes (see Section 3.3).

Multiple <codecs-excluded> elements MUST NOT be present in a
container element unless each applies to a different set of streams
(e.g., one <codecs-excluded> element for incoming and one for
outgoing streams). The <codecs-excluded> element MUST contain zero
or more <codec> elements.

A <codecs-excluded> element MUST NOT be used in a container that
contains a <codecs-allowed> element. The absence of both elements in
a container indicates no restrictions regarding codecs.

Merging of session-policy documents: <codecs-excluded> containers are
merged as described in "Merging Sets" Section 5.1.2.

5.7. The <local-ports> Element

Domains often require that a user agent only uses ports in a certain
range for media streams. The <local-ports> element defines a policy
for the ports a user agent can use for media. The value of this
element consists of the decimal representation of a start port number
and an end port number, separated by a hyphen ("-"). The start/end
port numbers are the first/last port numbers that can be used, that
is, the range is inclusive. The start/end port numbers must be in
the range 1 to 65535 (inclusive).

Hilt, et al. Standards Track [Page 18]

RFC 6796 Media Policy Data Set December 2012

As with other policy elements, there are values of the <local-ports>
element that allow no sessions. This happens if the start port
number is greater than the end port number.

The default value for <local-ports> is "1-65535".

This element MAY have the 'visibility' attribute (see Section 3.3).

Merging of session-policy documents: the permitted ranges specified
by the two policies are set-intersected. If the resulting set is
empty, the resulting <local-ports> element value MUST be any allowed
value with a start port number greater than the end port number.

6. Common Media Policy Data Set Elements

This section describes common XML elements that are used in session
info and session policy documents to encode the media properties of
SIP sessions.

6.1. The <media-type> Element

The <media-type> element identifies a specific media type. The value
of this element MUST be the name of a media type, as defined in
Section 8.2.1 of [RFC4566], such as audio, video, text, or
application.

This element MAY have the 'q' attribute (see Section 3.3).

If used in a session policy document inside a <media-types-allowed>
element, the media types defined MAY be used in a session. If used
in a session policy document inside a <media-types-excluded> element,
the media types defined MUST NOT be used in a session.

6.2. The <codec> Element

The <codec> element identifies a specific codec. The content of this
element MUST be a media type and subtype (e.g., audio/PCMA [RFC4856]
or video/H263 [RFC4629]), possibly with parameters.

The <codec> element MAY have the 'q' attribute (see Section 3.3).

If used in a session policy document inside a <codecs-allowed>
element, the codec defined MAY be used in a session. If used in a
session policy document inside a <codecs-excluded> element, the codec
defined MUST NOT be used in a session.

The <codec> element MUST contain one <media-type-subtype> element and
MAY contain multiple optional <mime-parameter> elements.

Hilt, et al. Standards Track [Page 19]

RFC 6796 Media Policy Data Set December 2012

6.2.1. The <media-type-subtype> Element

The <media-type-subtype> element contains a media type and subtype
that identifies a media format [RFC4566] (e.g., a codec). For audio
and video streams, the value of this element MUST be a media type and
subtype that is registered as an RTP Payload Type [RFC4855] separated
by a forward slash ("/"), e.g., audio/PCMA, audio/G726-16 [RFC4856],
or video/H263 [RFC4629]. For other media types, SDP sometimes
encodes the actual media format as part of the transport protocol
field (e.g., TCP/MSRP [RFC4975] and TCP/TLS/BFCP [RFC4583]). In
these cases, this element MUST contain the media type and the media
format part (e.g., message/msrp and application/bfcp).

6.2.2. The <mime-parameter> Element

The <mime-parameter> element may be needed for some codecs to
identify a particular encoding or profile. The value of this element
MUST be a name-value pair containing the name and the value of a
media type parameter for the codec [RFC4855]. The name and value are
separated by an equals sign ("="). For example, the parameter
"profile=0" can be used to specify a specific profile for the codec
video/H263-2000 [RFC4629].

6.3. The <max-bw> Element

The <max-bw> element defines the overall maximum bandwidth in
kilobits per second (i.e., 1024 bits per second) an entity can/will
use for media streams at any point in time. It defines an upper
limit for the total bandwidth an entity can/will use for the
transmission of media streams. The limit corresponds to the sum of
the maximum session bandwidth of all sessions a UA may set up in
parallel.

The bandwidth limit given in the <max-bw> element includes the
bandwidth needed for lower-layer transport and network protocols
(e.g., UDP and IP).

The <max-bw> element MAY have the 'direction' attribute (see
Section 3.3).

If used in a <session-policy> element, the <max-bw> element MAY also
have the 'visibility' attribute (see Section 3.3).

If the <max-bw> element occurs multiple times in a container element,
each instance MUST apply to a different set of media streams (i.e.,
one <max-bw> element for outgoing and one for incoming streams).

Hilt, et al. Standards Track [Page 20]

RFC 6796 Media Policy Data Set December 2012

Merging of session-policy documents: the lowest <max-bw> value MUST
be used.

6.4. The <max-session-bw> Element

The <max-session-bw> element defines the maximum bandwidth in
kilobits per second (i.e., 1024 bits per second) an entity can/will
use for media streams in the described session. It defines an upper
limit for the total bandwidth of a single session. This limit
corresponds to the sum of the maximum stream bandwidth of all media
streams in a session.

The bandwidth limit given in the <max-session-bw> element includes
the bandwidth needed for lower-layer transport and network protocols
(e.g., UDP and IP).

The <max-session-bw> element MAY have the 'direction' attribute (see
Section 3.3).

If used in a <session-policy> element, the <max-session-bw> element
MAY also have the 'visibility' attribute (see Section 3.3).

If the <max-session-bw> element occurs multiple times in a container
element, each instance MUST apply to a different set of media streams
(i.e., one <max-session-bw> element for outgoing and one for incoming
streams).

Merging of session-policy documents: the lowest <max-session-bw>
value MUST be used.

6.5. The <max-stream-bw> Element

The <max-stream-bw> element defines the maximum bandwidth in kilobits
per second (i.e., 1024 bits per second) an entity can/will use for
each media stream in the described session.

The bandwidth limit given in the <max-stream-bw> element includes the
bandwidth needed as encapsulated in IP (i.e., the RTP, UDP, and IP
overheads are included).

The <max-stream-bw> element MAY have the 'direction' and 'media-type'
attributes (see Section 3.3).

If used in a <session-policy> element, the <max-stream-bw> element
MAY also have the visibility attribute (see Section 3.3).

If used in a <session-info> element, the <max-stream-bw> element MAY
also have the label attribute.

Hilt, et al. Standards Track [Page 21]

RFC 6796 Media Policy Data Set December 2012

The media-type attribute is used to define that the <max-stream-bw>
element only applies to streams of a certain media type (e.g., audio
streams).

The <max-stream-bw> element is used to define a bandwidth limit for a
specific media stream. The use of this attribute requires that the
<stream> element that represents the media stream to which this
bandwidth limit applies also has a 'label' attribute. A
<max-stream-bw> element with a 'label' attribute applies only to the
stream element that has a 'label' attribute with the same value. If
no matching <stream> element exists, then the <max-stream-bw> element
MUST be ignored.

If the <max-stream-bw> element occurs multiple times in a container
element, each instance MUST apply to a different set of media streams
(i.e., one <max-stream-bw> element for outgoing and one for incoming
streams).

Merging of session-policy documents: the lowest <max-stream-bw> value
MUST be used.

6.6. The <qos-dscp> Element

The <qos-dscp> element contains a Differentiated Services Codepoint
(DSCP) [RFC2474] value that should be used to populate the IP DS
field of media packets. The <qos-dscp> contains a decimal integer
value that represents a 6-bit field and therefore ranges from 0 to
63.

This element MAY have the 'direction' and 'media-type' attributes
(see Section 3.3)).

If used in a <session-policy> element, the <qos-dscp> element MAY
also have the 'visibility' attribute (see Section 3.3).

The 'media-type' attribute is used to specify that the <qos-dscp>
element only applies to streams of a certain media type (e.g., audio
streams).

The <qos-dscp> element is optional and MAY occur multiple times
inside a container. If the <qos-dscp> element occurs multiple times,
each instance MUST apply to a different media stream (i.e., one <qos-
dscp> element for audio and one for video streams).

Hilt, et al. Standards Track [Page 22]

RFC 6796 Media Policy Data Set December 2012

Merging of session-policy documents: the local domain of the user
agent has precedence over other domains and its DSCP value MUST be
used. During the merging process, <qos-dscp> element values from
local policy server selected as described in "Local Policy Server
Selection" Section 5.1.3 are used.

6.7. The <context> Element

The <context> element provides context information about a session
policy or session information document.

The <context> element MAY contain multiple <contact> elements and one
<info> element. It can also contain optional <policy-server-URI> and
<token> elements.

If used in a <session-info> element, the <context> element MAY also
contain a <request-URI> element.

Merging of session-policy documents: the resulting <context> element
MUST be determined by local policy.

6.7.1. The <policy-server-URI> Element

The <policy-server-URI> element contains the URI (including the URI
scheme) of the policy server that has issued this policy.

6.7.2. The <contact> Element

The <contact> element contains a URI that is a contact address (e.g.,
a SIP URI or mailto URI) by which a human representative of the
issuer of this document can be reached.

6.7.3. The <info> Element

The <info> element provides a short textual description of the policy
or session that should be intelligible to the human user.

6.7.4. The <request-URI> Element

The <request-URI> element contains the request-URI (including the URI
scheme) of the dialog-initiating request of the session.

The <request-URI> element is only permitted inside <session-info>
documents and, thus, MUST NOT be included in session policy
documents.

Hilt, et al. Standards Track [Page 23]

RFC 6796 Media Policy Data Set December 2012

6.7.5. The <token> Element

The <token> element provides a mechanism for a policy server to
return an opaque string to a UA. Such a string is sometimes needed
to construct a Policy-ID header that ensures that all policy requests
concerning a single session are routed to the same policy server.
The use of this token is described in "A Framework for Session
Initiation Protocol (SIP) Session Policies" [RFC6794]. The syntax
for the token value is defined in Section 4.4.5.1 of RFC 6794
[RFC6794], which builds on the syntax defined in Section 25.1 of RFC
3261 [RFC3261]. (Note that the token value is encodable as a SIP URI
parameter value, although some characters may require escaping).

6.8. Other Session Properties

A number of additional elements have been proposed for a media
property language. These elements are deemed to be outside the scope
of this format. However, they may be defined in extensions of MPDF
or other profile data sets.

o maximum number of streams

o maximum number of sessions

o maximum number of streams per session

o external address and port

o media transport protocol

o outbound proxy

o SIP methods

o SIP option tags

o SIP transport protocol

o body disposition

o body format

o body encryption

Hilt, et al. Standards Track [Page 24]

RFC 6796 Media Policy Data Set December 2012

7. Examples

7.1. Session Policy Documents

The following example is a session policy document that allows the
use of audio and video and prohibits the use of other media types.
It allows the use of any codec except G.723 and G.729.

<session-policy xmlns="urn:ietf:params:xml:ns:mediadataset">
<context>
<policy-server-URI>sips:[email protected]</policy-server-URI>
<contact>sip:[email protected]</contact>
<info>Access network policies</info>
</context>
<media-types-allowed>
<media-type>audio</media-type>
<media-type>video</media-type>
</media-types-allowed>
<codecs-excluded>
<codec>
<media-type-subtype>audio/G729</media-type-subtype>
</codec>
<codec>
<media-type-subtype>audio/G723</media-type-subtype>
</codec>
</codecs-excluded>
</session-policy>

7.2. Session Information Documents

The following examples contain session descriptions and the session
information documents that represent these sessions.

7.2.1. Example 1

In this example, a session info document is created based on one
session description. This session info document would be created,
for example, by a UA that has composed an offer and is now contacting
a policy server.

Local session description:

v=0
o=alice 2890844526 2890844526 IN IP4 host.somewhere.example
s=
c=IN IP4 host.somewhere.example
t=0 0
m=audio 49562 RTP/AVP 0 1 3

Hilt, et al. Standards Track [Page 25]

RFC 6796 Media Policy Data Set December 2012

a=rtpmap:0 PCMU/8000
a=rtpmap:1 1016/8000
a=rtpmap:3 GSM/8000
m=video 51234 RTP/AVP 31 34
a=rtpmap:31 H261/90000
a=rtpmap:34 H263/90000

MPDF document:

<session-info xmlns="urn:ietf:params:xml:ns:mediadataset">
<context>
<contact>sip:[email protected]</contact>
<info>session information</info>
</context>
<streams>
<stream>
<media-type>audio</media-type>
<codec q="1.0">
<media-type-subtype>audio/PCMU</media-type-subtype>
</codec>
<codec q="0.9">
<media-type-subtype>audio/1016</media-type-subtype>
</codec>
<codec q="0.8">
<media-type-subtype>audio/GSM</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:49562</local-host-port>
</stream>
<stream>
<media-type>video</media-type>
<codec q="1.0">
<media-type-subtype>video/H261</media-type-subtype>
</codec>
<codec q="0.9">
<media-type-subtype>video/H263</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:51234</local-host-port>
</stream>
</streams>
</session-info>

7.2.2. Example 2

In this example, a session info document is created that represents
two session descriptions (i.e., an offer and answer). This session
info document would be created, for example, by a UA that has
received an answer from another UA and is now contacting a policy
server.

Hilt, et al. Standards Track [Page 26]

RFC 6796 Media Policy Data Set December 2012

Local session description:

v=0
o=alice 2890844526 2890844526 IN IP4 host.somewhere.example
s=
c=IN IP4 host.somewhere.example
t=0 0
m=audio 49562 RTP/AVP 0 1 3
a=rtpmap:0 PCMU/8000
a=rtpmap:1 1016/8000
a=rtpmap:3 GSM/8000
m=video 51234 RTP/AVP 31 34
a=rtpmap:31 H261/90000
a=rtpmap:34 H263/90000

Remote session description:

v=0
o=bob 2890844730 2890844730 IN IP4 host.anywhere.example
s=
c=IN IP4 host.anywhere.example
t=0 0
m=audio 52124 RTP/AVP 0 3
a=rtpmap:0 PCMU/8000
a=rtpmap:3 GSM/8000
m=video 50286 RTP/AVP 31
a=rtpmap:31 H261/90000

MPDF document that represents the local and the remote session
description:

<session-info xmlns="urn:ietf:params:xml:ns:mediadataset">
<context>
<contact>sip:[email protected]</contact>
<info>session information</info>
</context>
<streams>
<stream>
<media-type>audio</media-type>
<codec q="1.0">
<media-type-subtype>audio/PCMU</media-type-subtype>
</codec>
<codec q="0.9">
<media-type-subtype>audio/GSM</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:49562</local-host-port>
<remote-host-port>host.anywhere.example:52124</remote-host-port>
</stream>

Hilt, et al. Standards Track [Page 27]

RFC 6796 Media Policy Data Set December 2012

<stream>
<media-type>video</media-type>
<codec q="1.0">
<media-type-subtype>video/H261</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:51234</local-host-port>
<remote-host-port>host.anywhere.example:50286</remote-host-port>
</stream>
</streams>
</session-info>

The following MPDF document is a modified version of the above
document, which can be returned by a policy server. This document
reflects a policy that defines a maximum session bandwidth of 192
kbit and a maximum bandwidth for the H261 video stream of 128 kbit.

<session-info xmlns="urn:ietf:params:xml:ns:mediadataset">
<context>
<contact>sip:[email protected]</contact>
<info>modified session information</info>
</context>
<streams>
<stream label='1'>
<media-type>audio</media-type>
<codec q="1.0">
<media-type-subtype>audio/PCMU</media-type-subtype>
</codec>
<codec q="0.9">
<media-type-subtype>audio/GSM</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:49562</local-host-port>
<remote-host-port>host.anywhere.example:52124</remote-host-port>
</stream>
<stream label='2'>
<media-type>video</media-type>
<codec q="1.0">
<media-type-subtype>video/H261</media-type-subtype>
</codec>
<local-host-port>host.somewhere.example:51234</local-host-port>
<remote-host-port>host.anywhere.example:50286</remote-host-port>
</stream>
</streams>
<max-stream-bw label='2'>128</max-stream-bw>
<max-session-bw>192</max-session-bw>
</session-info>

Hilt, et al. Standards Track [Page 28]

RFC 6796 Media Policy Data Set December 2012

8. RELAX NG Definition

<?xml version="1.0"?>
<grammar xmlns="http://relaxng.org/ns/structure/1.0"
ns="urn:ietf:params:xml:ns:mediadataset"
datatypeLibrary="http://www.w3.org/2001/XMLSchema-datatypes">

<start>
<choice>
<element name="session-info">
<interleave>
<optional>
<ref name="ElementStreams"/>
</optional>
<zeroOrMore>
<ref name="ElementMaxBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMaxSessionBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMaxStreamBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMediaIntermediaries"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementQoSDSCP"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementAny"/>
</zeroOrMore>
</interleave>
</element>

<element name="session-policy">
<interleave>
<optional>
<ref name="ElementContext"/>
</optional>
<optional>
<ref name="ElementLocalPorts"/>
</optional>
<zeroOrMore>
<ref name="ElementMediaTypesAllowed"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMediaTypesExcluded"/>

Hilt, et al. Standards Track [Page 29]

RFC 6796 Media Policy Data Set December 2012

</zeroOrMore>
<zeroOrMore>
<ref name="ElementCodecsAllowed"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementCodecsExcluded"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMaxBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMaxSessionBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementMaxStreamBandwidth"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementQoSDSCP"/>
</zeroOrMore>
<zeroOrMore>
<ref name="ElementAny"/>
</zeroOrMore>
</interleave>
</element>
</choice>
</start>

<define name="ElementMediaTypesAllowed">
<element name="media-types-allowed">
<ref name="PolicyGeneralAttributes"/>
<zeroOrMore>
<ref name="ElementMediaType"/>
</zeroOrMore>
</element>
</define>

<define name="ElementMediaTypesExcluded">
<element name="media-types-excluded">
<ref name="PolicyGeneralAttributes"/>
<zeroOrMore>
<ref name="ElementMediaType"/>
</zeroOrMore>
</element>
</define>

<define name="ElementMediaType">
<element name="media-type">
<data type="string" />

Hilt, et al. Standards Track [Page 30]

RFC 6796 Media Policy Data Set December 2012

<optional>
<ref name="AttributeQ"/>
</optional>
<optional>
<ref name="AttributeGeneric"/>
</optional>
</element>
</define>

<define name="ElementCodecsAllowed">
<element name="codecs-allowed">
<ref name="PolicyGeneralAttributes"/>
<zeroOrMore>
<ref name="ElementCodec"/>
</zeroOrMore>
</element>
</define>

<define name="ElementCodecsExcluded">
<element name="codecs-excluded">
<ref name="PolicyGeneralAttributes"/>
<zeroOrMore>
<ref name="ElementCodec"/>
</zeroOrMore>
</element>
</define>

<define name="ElementCodec">
<element name="codec">
<optional>
<ref name="AttributeQ"/>
</optional>
<optional>
<ref name="AttributeGeneric"/>
</optional>
<element name="media-type-subtype">
<data type="string" />
</element>
<zeroOrMore>
<element name="mime-parameter">
<data type="string" />
</element>
</zeroOrMore>
</element>
</define>

Hilt, et al. Standards Track [Page 31]

RFC 6796 Media Policy Data Set December 2012

<define name="ElementStreams">
<element name="streams">
<optional>
<ref name="AttributeGeneric"/>
</optional>
<zeroOrMore>
<ref name="ElementStream"/>
</zeroOrMore>
</element>
</define>

<define name="ElementStream">
<element name="stream">
<optional>
<ref name="AttributeDirection"/>
</optional>
<optional>
<ref name="AttributeLabel"/>
</optional>
<optional>
<ref name="AttributeEnabled"/>
</optional>
<optional>
<ref name="AttributeGeneric"/>
</optional>
<ref name="ElementMediaType"/>
<oneOrMore>
<ref name="ElementCodec"/>
</oneOrMore>
<element name="local-host-port">
<data type="string" />
</element>
<optional>
<element name="remote-host-port">
<data type="string" />
</element>
</optional>
</element>
</define>

<define name="ElementMaxBandwidth">
<element name="max-bw">
<data type="integer" />
<ref name="PolicyGeneralAttributes"/>
</element>
</define>

Hilt, et al. Standards Track [Page 32]

RFC 6796 Media Policy Data Set December 2012

<define name="ElementMaxSessionBandwidth">
<element name="max-session-bw">
<data type="integer" />
<ref name="PolicyGeneralAttributes"/>
</element>
</define>

<define name="ElementMaxStreamBandwidth">
<element name="max-stream-bw">
<data type="integer" />
<ref name="PolicyGeneralAttributes"/>
<optional>
<ref name="AttributeMediaType"/>
</optional>
<optional>
<ref name="AttributeLabel"/>
</optional>
</element>
</define>

<define name="ElementMediaIntermediaries">
<element name="media-intermediaries">
<ref name="PolicyGeneralAttributes"/>
<oneOrMore>
<choice>
<element name="fixed-intermediary">
<element name="int-host-port">
<data type="string" />
</element>
<zeroOrMore>
<element name="int-addl-port">
<data type="integer" />
</element>
</zeroOrMore>
</element>

<element name="turn-intermediary">
<element name="int-host-port">
<data type="string" />
</element>
<zeroOrMore>
<element name="int-addl-port">
<data type="integer" />
</element>
</zeroOrMore>
<zeroOrMore>
<element name="shared-secret">
<data type="string" />

Hilt, et al. Standards Track [Page 33]

RFC 6796 Media Policy Data Set December 2012

</element>
</zeroOrMore>
</element>
</choice>
</oneOrMore>
</element>
</define>

<define name="ElementQoSDSCP">
<element name="qos-dscp">
<data type="integer" />
<ref name="PolicyGeneralAttributes"/>
<optional>
<ref name="AttributeMediaType"/>
</optional>
</element>
</define>

<define name="ElementLocalPorts">
<element name="local-ports">
<data type="string" />
<interleave>
<optional>
<ref name="AttributeVisibility"/>
</optional>
<optional>
<ref name="AttributeGeneric"/>
</optional>
</interleave>
</element>
</define>

<define name="ElementContext">
<element name="context">
<interleave>
<optional>
<element name="info">
<data type="string" />
</element>
</optional>
<optional>
<element name="policy-server-URI">
<data type="string" />
</element>
</optional>
<optional>
<element name="token">
<data type="token" />

Hilt, et al. Standards Track [Page 34]

RFC 6796 Media Policy Data Set December 2012

</element>
</optional>
<optional>
<element name="request-URI">
<data type="string" />
</element>
</optional>
<zeroOrMore>
<element name="contact">
<data type="string" />
</element>
</zeroOrMore>
</interleave>
</element>
</define>

<define name="PolicyGeneralAttributes">
<optional>
<ref name="AttributeVisibility"/>
</optional>
<optional>
<ref name="AttributeDirection"/>
</optional>
<optional>
<ref name="AttributeGeneric"/>
</optional>
</define>

<define name="AttributeVisibility">
<attribute name="visibility">
<choice>
<value>hidden</value>
<value>visible</value>
</choice>
</attribute>
</define>

<define name="AttributeDirection">
<attribute name="direction">
<choice>
<value>sendonly</value>
<value>recvonly</value>
<value>sendrecv</value>
</choice>
</attribute>
</define>

Hilt, et al. Standards Track [Page 35]

RFC 6796 Media Policy Data Set December 2012

<define name="AttributeQ">
<attribute name="q">
<data type="decimal" />
</attribute>
</define>

<define name="AttributeMediaType">
<attribute name="media-type">
<data type="string" />
</attribute>
</define>

<define name="AttributeLabel">
<attribute name="label">
<data type="string" />
</attribute>
</define>

<define name="AttributeEnabled">
<attribute name="enabled">
<data type="boolean" />
</attribute>
</define>

<define name="AttributeGeneric">
<zeroOrMore>
<attribute>
<anyName>
<except>
<name ns="">visibility</name>
<name ns="">direction</name>
<name ns="">q</name>
<name ns="">media-type</name>
<name ns="">label</name>
<name ns="">enabled</name>
</except>
</anyName>
</attribute>
</zeroOrMore>
</define>

<define name="ElementAny">
<element>
<anyName>
<except>
<name>context</name>
<name>streams</name>
<name>max-bw</name>

Hilt, et al. Standards Track [Page 36]

RFC 6796 Media Policy Data Set December 2012

<name>max-session-bw</name>
<name>max-stream-bw</name>
<name>media-intermediaries</name>
<name>qos-dscp</name>
<name>local-ports</name>
<name>media-types-allowed</name>
<name>media-types-excluded</name>
<name>media-type</name>
<name>codecs-allowed</name>
<name>codecs-excluded</name>
</except>
</anyName>
<ref name="anyExtension"/>
</element>
</define>

<define name="anyExtension">
<zeroOrMore>
<choice>
<element>
<anyName/>
<ref name="anyExtension"/>
</element>
<attribute>
<anyName/>
</attribute>
<text/>
</choice>
</zeroOrMore>
</define>

</grammar>

9. Security Considerations

Section 5 of [RFC6794] discusses security aspects related to the
transfer of session policy information between user agents and policy
servers, including their authentication and the use of TLS between
them. In particular, a UA needs to check the server's certificate
and only accept policies from severs from which the UA is configured
to accept policies. Section 7 of RFC 3470 [RFC3470] provides general
security considerations regarding the transport of XML documents in
network protocols. Session info and session policy information can
be sensitive information. The protocol used to distribute session
info and session policy documents SHOULD ensure authentication,
confidentiality, and message integrity. The use of [RFC6795] to
distribute session info and session policy document meets these
requirements.

Hilt, et al. Standards Track [Page 37]

RFC 6796 Media Policy Data Set December 2012

An attacker could attempt to modify session policy documents that
were sent to a client so that their processing by the client would be
more costly (e.g., in terms of merging policies). The attacker could
also attempt to create its own fake policy documents and send them to
the client with the same purpose or in order to get the client to
comply with those fake policies as part of a Denial-of-Service (DoS)
attack. The protocol used to distribute session policy documents
SHOULD ensure authentication, privacy, and message integrity. The
use of [RFC6795] to distribute session policy document meets these
requirements.

The <shared-secret> element can contain a shared secret needed to
authenticate at a media intermediary. The privacy of documents
containing this element MUST be preserved when they are sent between
a server and a UA. When [RFC6795] is used to distribute these
documents, encryption as defined in [RFC3261] (i.e., TLS or S/MIME)
MUST be used.

10. IANA Considerations

This document registers a new media type (application/
media-policy-dataset+xml), a new RELAX NG schema, and a new XML
namespace.

10.1. Media Type Registration

Media type name: application

Media subtype name: media-policy-dataset+xml

Mandatory parameters: none

Optional parameters: Same as charset parameter of application/xml as
specified in RFC 3023 [RFC3023].

Encoding considerations: Same as encoding considerations of
application/xml as specified in RFC 3023 [RFC3023].

Security considerations: See Section 10 of RFC 3023 [RFC3023] and
Section 9 of this specification.

Interoperability considerations: none.

Published specification: This document.

Applications that use this media type: This document type is used to
convey session description and media policy information between SIP
user agents and a domain.

Hilt, et al. Standards Track [Page 38]

RFC 6796 Media Policy Data Set December 2012

Additional Information:

Magic Number: None

File Extension: .mpf or .xml

Macintosh file type code: "TEXT"

Personal and email address for further information: Volker Hilt
<[email protected]>

Intended usage: COMMON

Author/Change controller: The IETF.

10.2. RELAX NG Schema Registration

This specification registers a schema. The schema can be found as
the sole content of Section 8.

URI: urn:ietf:params:xml:schema:mediadataset

Registrant Contact: IETF RAI area <[email protected]>, Volker Hilt
<[email protected]>

RELAX NG Schema: The RELAX NG schema to be registered is contained in
Section 8.

10.3. URN Sub-Namespace Registration

This section registers a new XML namespace, as per the guidelines in
[RFC3688].

URI: The URI for this namespace is
urn:ietf:params:xml:ns:mediadataset.

Registrant Contact: IETF RAI area <[email protected]>, Volker Hilt
<[email protected]>

Hilt, et al. Standards Track [Page 39]

RFC 6796 Media Policy Data Set December 2012

XML:

BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Media Policy Data Set Namespace</title>
</head>
<body>
<h1>Namespace for Media Policy Data Sets</h1>
<h2>urn:ietf:params:xml:ns:mediadataset</h2>
<p>See <a href="http://www.rfc-editor.org/rfc/rfc6796.txt">
RFC 6796</a>.</p>
</body>
</html>
END

11. References

11.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2141] Moats, R., "URN Syntax", RFC 2141, May 1997.

[RFC2474] Nichols, K., Blake, S., Baker, F., and D. Black,
"Definition of the Differentiated Services Field (DS
Field) in the IPv4 and IPv6 Headers", RFC 2474,
December 1998.

[RFC3023] Murata, M., St. Laurent, S., and D. Kohn, "XML Media
Types", RFC 3023, January 2001.

[RFC3264] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
with Session Description Protocol (SDP)", RFC 3264,
June 2002.

[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.

[RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
Description Protocol", RFC 4566, July 2006.

Hilt, et al. Standards Track [Page 40]

RFC 6796 Media Policy Data Set December 2012

[RFC4574] Levin, O. and G. Camarillo, "The Session Description
Protocol (SDP) Label Attribute", RFC 4574, August 2006.

[RFC4855] Casner, S., "Media Type Registration of RTP Payload
Formats", RFC 4855, February 2007.

[RFC4975] Campbell, B., Mahy, R., and C. Jennings, "The Message
Session Relay Protocol (MSRP)", RFC 4975, September 2007.

[RFC4976] Jennings, C., Mahy, R., and A. Roach, "Relay Extensions
for the Message Sessions Relay Protocol (MSRP)", RFC 4976,
September 2007.

[RFC5766] Mahy, R., Matthews, P., and J. Rosenberg, "Traversal Using
Relays around NAT (TURN): Relay Extensions to Session
Traversal Utilities for NAT (STUN)", RFC 5766, April 2010.

[RFC6795] Hilt, V. and G. Camarillo, "A Session Initiation Protocol
(SIP) Event Package for Session-Specific Policies",
RFC 6795, December 2012.

[W3C.REC-xml-20081126]
Sperberg-McQueen, C., Yergeau, F., Maler, E., Bray, T.,
and J. Paoli, "Extensible Markup Language (XML) 1.0 (Fifth
Edition)", World Wide Web Consortium Recommendation REC-
xml-20081126, November 2008,
<http://www.w3.org/TR/2008/REC-xml-20081126>.

[W3C.REC-xml-names-19990114]
Hollander, D., Bray, T., and A. Layman, "Namespaces in
XML", World Wide Web Consortium First Edition REC-xml-
names-19990114, January 1999,
<http://www.w3.org/TR/1999/REC-xml-names-19990114>.

11.2. Informative References

[RFC2648] Moats, R., "A URN Namespace for IETF Documents", RFC 2648,
August 1999.

[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.

[RFC3470] Hollenbeck, S., Rose, M., and L. Masinter, "Guidelines for
the Use of Extensible Markup Language (XML)
within IETF Protocols", BCP 70, RFC 3470, January 2003.

Hilt, et al. Standards Track [Page 41]

RFC 6796 Media Policy Data Set December 2012

[RFC4583] Camarillo, G., "Session Description Protocol (SDP) Format
for Binary Floor Control Protocol (BFCP) Streams",
RFC 4583, November 2006.

[RFC4629] Ott, H., Bormann, C., Sullivan, G., Wenger, S., and R.
Even, "RTP Payload Format for ITU-T Rec", RFC 4629,
January 2007.

[RFC4856] Casner, S., "Media Type Registration of Payload Formats in
the RTP Profile for Audio and Video Conferences",
RFC 4856, February 2007.

[RFC6080] Petrie, D. and S. Channabasappa, "A Framework for Session
Initiation Protocol User Agent Profile Delivery",
RFC 6080, March 2011.

[RFC6794] Hilt, V., Camarillo, G., and J. Rosenberg, "A Framework
for Session Initiation Protocol (SIP) Session Policies",
RFC 6794, December 2012.

Hilt, et al. Standards Track [Page 42]

RFC 6796 Media Policy Data Set December 2012

Appendix A. Acknowledgements

Many thanks to Allison Mankin, Dan Petrie, Martin Dolly, Adam Roach,
and Ben Campbell for the discussions and suggestions. Many thanks to
Roni Even, Mary Barnes, Yaron Sheffer, Pete McCann, and Henry S.
Thompson for reviewing the document and to Jari Urpalainen for
helping with the RELAX NG schema.

Authors' Addresses

Volker Hilt
Bell Labs/Alcatel-Lucent
Lorenzstrasse 10
70435 Stuttgart
Germany

EMail: [email protected]

Gonzalo Camarillo
Ericsson
Hirsalantie 11
Jorvas 02420
Finland

EMail: [email protected]

Jonathan Rosenberg
jdrosen.net
Monmouth, NJ
USA

EMail: [email protected]

Dale R. Worley
Ariadne Internet Services, Inc.
738 Main St.
Waltham, MA 02451
US

EMail: [email protected]

Hilt, et al. Standards Track [Page 43]