Network Working Group T. Nadeau
Request for Comments: 4221 Cisco Systems, Inc.
Category: Informational C. Srinivasan
Bloomberg L.P.
A. Farrel
Old Dog Consulting
November 2005
Multiprotocol Label Switching (MPLS) Management Overview
Status of This Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
A range of Management Information Base (MIB) modules has been
developed to help model and manage the various aspects of
Multiprotocol Label Switching (MPLS) networks. These MIB modules are
defined in separate documents that focus on the specific areas of
responsibility of the modules that they describe.
This document describes the management architecture for MPLS and
indicates the interrelationships between the different MIB modules
used for MPLS network management.
Table of Contents
1. Introduction ....................................................3
2. Terminology .....................................................3
3. The SNMP Management Framework ...................................3
4. An Introduction to the MPLS Working Group MIB Modules ...........4
4.1. Structure of the MPLS MIB OID Tree .........................5
4.2. MPLS-TC-STD-MIB ............................................5
4.3. MPLS-LSR-STD-MIB ...........................................5
4.4. MPLS-LDP-STD-MIB ...........................................6
4.5. MPLS-LDP-GENERIC-STD-MIB ...................................6
4.6. MPLS-LDP-ATM-STD-MIB .......................................6
4.7. MPLS-LDP-FRAME-RELAY-STD-MIB ...............................7
4.8. MPLS-TE-STD-MIB ............................................7
4.9. MPLS-FTN-STD-MIB ...........................................7
Nadeau, et al. Informational [Page 1]
RFC 4221 MPLS Management Overview November 2005
4.10. TE-LINK-STD-MIB ...........................................7
4.11. MIB Module Interdependencies ..............................8
4.12. Dependencies on External MIB Modules ......................9
5. Tables, Scalars, and Notifications in MPLS-LSR-STD-MIB .........10
5.1. Tables ....................................................10
5.2. Scalars ...................................................10
5.3. Indexing ..................................................11
5.4. Notifications .............................................12
5.5. Dependencies between MIB Module Tables ....................12
6. Tables, Scalars, and Notifications in the LDP MIB ..............13
6.1. MIB Modules ...............................................13
6.2. Tables ....................................................14
6.3. Scalars ...................................................15
6.4. Notifications .............................................15
6.5. Dependencies between MIB Module Tables ....................15
7. Tables, Scalars, and Notifications in MPLS-TE-STD-MIB ..........16
7.1. Tables ....................................................16
7.2. Scalars ...................................................17
7.3. Notifications .............................................18
7.4. Dependencies between MIB Module Tables ....................18
8. Tables, Scalars, and Notifications in MPLS-FTN-STD-MIB .........18
8.1. Tables ....................................................18
8.2. Scalars ...................................................19
8.3. Notifications .............................................19
8.4. Dependencies between MIB Module Tables ....................19
9. Tables and Objects in TE-LINK-STD-MIB ..........................19
9.1. Tables ....................................................19
9.2. Scalars ...................................................20
9.3. Notifications .............................................20
9.4. Dependencies between MIB Module Tables ....................20
10. Table Dependencies between MPLS MIB Modules ...................21
11. A Note on Interfaces ..........................................21
11.1. MPLS Tunnels as Interfaces ...............................21
11.2. Application of the Interfaces Group to TE Links ..........22
11.3. References to Interface MIB Objects from MPLS MIB
Modules ..................................................23
12. Management Options ............................................24
13. Related IETF MIB Modules ......................................25
13.1. PWE3 Working Group MIB Modules ...........................26
13.2. PPVPN Working Group MIB Modules ..........................26
13.2.1. PPVPN-MPLS-VPN-STD-MIB ............................26
13.3. CCAMP Working Group MIB Modules ..........................26
14. Traffic Engineering Working Group TE MIB ......................27
14.1. Choosing between TE MIB Modules ..........................27
15. Security Considerations .......................................28
16. Acknowledgements ..............................................28
17. Normative References ..........................................29
18. Informative References ........................................30
Nadeau, et al. Informational [Page 2]
RFC 4221 MPLS Management Overview November 2005
1. Introduction
This document describes the Management Architecture for Multi-
Protocol Label Switching (MPLS) [RFC3031]. In particular, it
describes how the managed objects defined in various MPLS-related
Management Information Base (MIB) documents model different aspects
of MPLS. Furthermore, this document explains the interactions and
dependencies between each of these MIB modules.
For additional information, this document also includes a brief note
on MIB modules produced by the Pseudo Wire Emulation Edge to Edge
(PWE3), Provider Provisioned Virtual Private Network (PPVPN), Common
Control and Measurement Plane (CCAMP), and Internet Traffic
Engineering (TEWG) working groups.
The document begins with a brief outline of the SNMP framework. This
is not intended to be a complete reference on SNMP, but is provided
to give context to the rest of the document and to indicate reference
material for readers that need to know more about SNMP.
This document does not propose any additions to the MPLS MIB
framework, nor define any standards for the Internet community. It
is an informational document. In all cases, the reader is advised to
turn to the document that defines the MIB module in question for
further information.
Comments should be made directly to the MPLS mailing list at
[email protected].
2. Terminology
This document uses terminology from the MPLS architecture document
[RFC3031] and the following MPLS related MIB modules: MPLS TC MIB
[TCMIB], MPLS LSR MIB [LSRMIB], MPLS TE MIB [TEMIB], MPLS LDP MIB
[LDPMIB], MPLS FTN MIB [FTNMIB], TE LINK MIB [TELMIB], and PPVPN MPLS
VPN MIB [VPNMIB].
Throughout this document hyphenated MIB names (such as MPLS-TE-STD-
MIB) should be taken to refer to specific MIB modules. Non-
hyphenated MIB names (such as MPLS LDP MIB) indicate MIB documents.
3. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Nadeau, et al. Informational [Page 3]
RFC 4221 MPLS Management Overview November 2005
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This document specifies a
MIB module that is compliant to the SMIv2, which is described in STD
58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
2580 [RFC2580].
4. An Introduction to the MPLS Working Group MIB Modules
This section addresses the MIB documents produced by the MPLS working
group, namely MPLS TC MIB, MPLS LSR MIB, MPLS TE MIB, MPLS LDP MIB,
MPLS FTN MIB, and TE LINK MIB. The rest of this section briefly
describes the following:
- the MPLS Object Identifier (OID) tree structure and the position
of different MPLS related MIB modules on this tree;
- the purpose of each of the MIB modules within the MIB documents,
what it can be used for, and how it relates to the other MIB
modules.
Note that each MIB document contains one or more compliance
statements for the modules and objects that it defines. Therefore,
the support for the different MIB modules and objects is beyond the
scope of this document, although some recommendations are included in
the sections that follow.
Nadeau, et al. Informational [Page 4]
RFC 4221 MPLS Management Overview November 2005
4.1. Structure of the MPLS MIB OID Tree
The MPLS MIB OID tree has the following structure.
transmission -- RFC 2578 [RFC2578]
|
+- mplsStdMIB -- MPLS-TC-STD-MIB
| |
| +- mplsTCStdMIB -- MPLS-TC-STD-MIB
| |
| +- mplsLsrStdMIB -- MPLS-LSR-STD-MIB
| |
| +- mplsTeStdMIB -- MPLS-TE-STD-MIB
| |
| +- mplsLdpStdMIB -- MPLS-LDP-STD-MIB
| |
| +- mplsLdpAtmStdMIB -- MPLS-LDP-ATM-STD-MIB
| |
| +- mplsLdpFrameRelayStdMIB -- MPLS-LDP-FRAME-RELAY-STD-MIB
| |
| +- mplsLdpGenericStdMIB -- MPLS-LDP-GENERIC-STD-MIB
| |
| +- mplsFTNStdMIB -- MPLS-FTN-STD-MIB
|
+- teLinkStdMIB -- TE-LINK-STD-MIB
Note: The OIDs for MIB modules are assigned and managed by IANA.
They can be found in the referenced MIB documents.
4.2. MPLS-TC-STD-MIB
MPLS-TC-STD-MIB defines textual conventions [RFC2579] that may be
common to MPLS-related MIB modules. These conventions allow multiple
MIB modules to use the same syntax and format for a concept that is
shared between the MIB modules.
For example, labels are a central part of MPLS and need to be
presented in many of the MIB modules. The textual convention for
representing an MPLS label is defined in MPLS-TC-STD-MIB.
All of the other MPLS MIB modules import textual conventions from
this MIB module.
4.3. MPLS-LSR-STD-MIB
MPLS-LSR-STD-MIB describes managed objects for modeling an MPLS Label
Switching Router (LSR). This puts it at the heart of the management
architecture for MPLS.
Nadeau, et al. Informational [Page 5]
RFC 4221 MPLS Management Overview November 2005
This MIB module is used to model and manage the basic label switching
behavior of an MPLS LSR. It represents the label forwarding
information base (LFIB) of the LSR and provides a view of the LSPs
that are being switched by the LSR in question.
Since basic MPLS label switching is common to all MPLS applications,
this MIB module is referenced by many of the other MPLS MIB modules.
In general, MPLS-LSR-STD-MIB provides a model of incoming labels on
MPLS-enabled interfaces being mapped to outgoing labels on MPLS-
enabled interfaces via a conceptual object called an MPLS cross-
connect. MPLS cross-connect entries and their properties are
represented in MPLS-LSR-STD-MIB and are typically referenced by other
MIB modules in order to refer to the underlying MPLS LSP.
For example, MPLS-TE-STD-MIB models traffic-engineered tunnels.
These tunnels map to one or more underlying MPLS LSPs. MPLS-TE-STD-
MIB refers to the underlying LSPs by pointing to cross-connect
entries in MPLS-LSR-STD-MIB.
4.4. MPLS-LDP-STD-MIB
MPLS-LDP-STD-MIB describes managed objects used to model and manage
the MPLS Label Distribution Protocol (LDP) [RFC3036]. LDP is one of
the MPLS protocols used to distribute labels and establish LSPs.
This MIB module contains objects common to all LDP implementations.
For an LDP implementation that provides standard MIB support, this
MIB module provides the core set of objects that are needed, along
with one or more of the other LDP MIB modules from the following
sections.
4.5. MPLS-LDP-GENERIC-STD-MIB
This MIB module provides objects for managing the LDP Per Platform
Label Space and is typically implemented along with the MPLS-LDP-
STD-MIB module. This MIB Module contains tables for configuring MPLS
Generic Label Ranges. Although the LDP Specification does not
provide a way to configure Label Ranges for Generic Labels, the MIB
module does provide a way to reserve a range of generic labels
because the working group thought this was useful.
4.6. MPLS-LDP-ATM-STD-MIB
This MIB module is typically supported along with MPLS-LDP-STD-MIB by
LDP implementations if LDP uses ATM as the Layer 2 medium. Tables in
this MIB module allow for configuring LDP to use ATM.
Nadeau, et al. Informational [Page 6]
RFC 4221 MPLS Management Overview November 2005
4.7. MPLS-LDP-FRAME-RELAY-STD-MIB
This MIB module is typically supported along with MPLS-LDP-STD-MIB by
LDP implementations if LDP uses Frame Relay as the Layer 2 medium.
Tables in this MIB module allow for configuration of LDP to use Frame
Relay.
4.8. MPLS-TE-STD-MIB
MPLS-TE-STD-MIB describes managed objects that are used to model and
manage MPLS Traffic Engineered (TE) Tunnels.
This MIB module is based on a table that represents TE tunnels that
either originate from, traverse via, or terminate on the LSR in
question. The MIB module provides configuration and statistics
objects needed for TE tunnels.
4.9. MPLS-FTN-STD-MIB
MPLS-FTN-STD-MIB describes managed objects that are used to model and
manage the MPLS FEC-to-NHLFE (FTN) mappings that take place at an
ingress Label Edge Router (LER).
An LER is an LSR placed at the edge of an MPLS domain, and it passes
traffic into and out of the MPLS domain. An ingress LER is
responsible for classifying data and assigning it to a suitable LSP
or tunnel.
This classification is done using Forwarding Equivalence Classes
(FECs) that define the common attributes of data (usually packets)
that will be treated in the same way. Once data has been classified,
it can be handed off to an LSP or tunnel through the Next Hop Label
Forwarding Entry (NHLFE).
In the case of an IP-to-MPLS mapping, the FEC objects describe IP
6-tuples that represent source and destination address ranges, source
and destination port ranges, the IPv4 Protocol field or IPv6 next-
header field, and the DiffServ Code Point (DSCP).
4.10. TE-LINK-STD-MIB
TE-LINK-STD-MIB describes managed objects that are used to model and
manage TE links, including bundled links, in an MPLS network.
The TE link feature is designed to aggregate one or more similar data
channels or TE links between a pair of LSRs. A TE link is a sub-
interface capable of carrying traffic-engineered MPLS traffic.
Nadeau, et al. Informational [Page 7]
RFC 4221 MPLS Management Overview November 2005
A bundled link is a sub-interface that bonds the traffic of a group
of one or more TE links.
4.11. MIB Module Interdependencies
This section provides an overview of the relationship between the
MPLS MIB modules described above. More details of these
relationships are given below after the MIB modules have been
discussed in more detail.
The arrows in the following diagram show a 'depends on' relationship.
A relationship "MIB module A depends on MIB module B" means that MIB
module A uses an object, object identifier, or textual convention
defined in MIB module B, or that MIB module A contains a pointer
(index or RowPointer) to an object in MIB module B.
+-------> MPLS-TC-STD-MIB
| ^
| |
| MPLS-LSR-STD-MIB <------------------+
| |
+<----------------------- MPLS-LDP-STD-MIB -->+
| ^ |
| | |
+<-- MPLS-LDP-GENERIC-STD-MIB ------>+ |
| | |
+<-- MPLS-LDP-ATM-STD-MIB ---------->+ |
| | |
+<-- MPLS-LDP-FRAME-RELAY-STD-MIB -->+ |
| |
+<------- MPLS-TE-STD-MIB ------------------->+
| ^ |
| | |
+<------- MPLS-FTN-STD-MIB ------------------>+
Thus:
- All the MPLS MIB modules depend on MPLS-TC-STD-MIB.
- MPLS-LDP-STD-MIB, MPLS-TE-STD-MIB, and MPLS-FTN-STD-MIB contain
references to objects in MPLS-LSR-STD-MIB.
- MPLS-LDP-GENERIC-STD-MIB, MPLS-LDP-ATM-STD-MIB, and MPLS-LDP-
FRAME-RELAY-STD-MIB contain references to objects in MPLS-LDP-
STD-MIB.
- MPLS-FTN-STD-MIB contains references to objects in MPLS-TE-STD-
MIB.
Nadeau, et al. Informational [Page 8]
RFC 4221 MPLS Management Overview November 2005
Note that there is a textual convention (MplsIndexType) defined in
MPLS-LSR-STD-MIB that is imported by MPLS-LDP-STD-MIB.
4.12. Dependencies on External MIB Modules
With the exception of MPLS-TC-STD-MIB, all the MPLS MIB modules have
dependencies on the Interfaces MIB [RFC2863]. MPLS-FTN-STD-MIB
references IP-capable interfaces on which received traffic is to be
classified using indexes in the Interface Table (ifTable) of IF-MIB
[RFC2863]. The other MPLS MIB modules reference MPLS-capable
interfaces in ifTable.
The Interfaces Group of IF-MIB [RFC2863] defines generic managed
objects for managing interfaces. The MPLS MIB modules contain
media-specific extensions to the Interfaces Group for managing MPLS
interfaces.
The MPLS MIB modules assume the interpretation of the Interfaces
Group to be in accordance with [RFC2863], which states that ifTable
contains information on the managed resource's interfaces and that
each sub-layer below the internetwork layer of a network interface is
considered an interface. Thus, the MPLS interface is represented as
an entry in ifTable.
The interrelation of entries in ifTable is defined by the Interfaces
Stack Group defined in [RFC2863].
Additionally, MPLS-LDP-ATM-STD-MIB imports the textual convention
AtmVpIdentifier from ATM-TC-MIB to represent an ATM virtual path
identifier, whereas MPLS-LDP-FRAME-RELAY-STD-MIB imports the textual
convention DLCI from FRAME-RELAY-DTE-MIB to represent a Data Link
Channel identifier.
MPLS-LDP-STD-MIB imports the textual conventions IndexInteger and
IndexIntegerNextFree from [RFC3289], and MPLS-TE-STD-MIB imports
IndexIntegerNextFree. IndexInteger provides a standard arbitrary
index, whereas IndexIntegerNextFree is used by a management agent
that needs to select an appropriate value for an arbitrary index.
Finally, all of the MIB modules import standard textual conventions
such as integers, strings, timestamps, etc., from the MIB modules in
which they are defined. This is business as usual for a MIB module
and is not discussed further in this document.
Nadeau, et al. Informational [Page 9]
RFC 4221 MPLS Management Overview November 2005
5. Tables, Scalars, and Notifications in MPLS-LSR-STD-MIB
5.1. Tables
MPLS-LSR-STD-MIB contains the following tables.
- The interface configuration table (mplsInterfaceTable) is used for
enabling MPLS on MPLS-capable interfaces.
- The in-segment (mplsInSegmentTable) and out-segment
(mplsOutSegmentTable) tables are used to configure and monitor LSP
segments carrying data into and out of the LSR, respectively.
- The in-segment mapping table (mplsInSegmentMapTable) provides a
look-up table that enables the discovery of an in-segment in
mplsInSegmentTable from the known incoming interface and incoming
label.
- The cross-connect table (mplsXCTable) is used to associate in and
out segments in order to form a cross-connect (i.e., to represent
an LSP transiting the LSR).
- The label stack table (mplsLabelStackTable) allows the
specification of multi-label stacks to be imposed on a given LSP
at this LSR.
- The MPLS in-segment (mplsInSegmentPerfTable) and out-segment
(mplsOutSegmentPerfTable) performance tables contain objects to
measure the performance of LSPs.
- The MPLS interface performance table (mplsInterfacePerfTable) has
objects to measure MPLS performance on a per-interface basis.
5.2. Scalars
Where tables in the MIB module have arbitrary indexes, scalars are
provided to supply the next available index. This applies to
mplsInSegmentTable, mplsOutSegmentTable, mplsXCTable, and
mplsLabelStackTable, but see the section on indexing, below.
mplsMaxLabelStackDepth defines the maximum size of a imposed label
stack supported at this LSR (and not, as the description in MPLS-
LSR-STD-MIB states, the maximum label stack depth supported by the
LSR).
mplsXCNotificationsEnable is used to enable and disable notifications
from MPLS-LSR-STD-MIB.
Nadeau, et al. Informational [Page 10]
RFC 4221 MPLS Management Overview November 2005
5.3. Indexing
Note that the indexing used by the tables in MPLS-LSR-STD-MIB is
unusual. A specific textual convention, MplsIndexType, is defined in
the MIB module and is used as the type for indexes to
mplsInSegmentTable, mplsOutSegmentTable, mplsXCTable, and
mplsLabelStackTable. The textual convention is defined as an octet
string of between one and twenty-four octets, inclusive.
Although this convention can be used to map simple integers and so
preserve the normal indexing techniques, it may also be used to
encode more complex indexing rules that may be useful to
implementations that subdivide their label spaces according to
physical or implementation constraints (such as placing the
responsibility for a subset of labels with a line card).
Note that it would be unusual, but not impossible, to make
sophisticated use of these indexes in a write-access MIB since the
'next' index value would be hard to determine. Thus, non-simple
values are likely only to be used in read-only MIBs in which the
indexes are generated as a result of signaling protocol
implementations or other configuration means. The formatting and
interpretation of non-simple indexes is out of the scope of the MIB
module definition and is expected to be part of the manageability
statement for a particular device. When the formatting is not known
by an agent, it should treat the index as a plain octet string
containing an integer of between one and twenty-four octets.
As described in the previous section, scalars are provided to allow
agents to discover a suitable value to use as an index when creating
a new row in one of these tables. These scalars all use a second
textual convention, MplsIndexNextType, also defined within MPLS-LSR-
STD-MIB. This textual convention allows the 'null string', (that is,
a string of length one octet with value 0x00). The null string is
used to indicate that either write access is not supported or no more
indexes are currently available.
Note that the usage of the nextIndex scalars is such that at any time
a scalar supplies a value that is currently unused as an index to the
specific table. In order to avoid lacunae in the indexing of a table
under normal usage, implementations are recommended to change the
value in an nextIndex scalar only when the index is used (that is,
when a row is created) and not when the nextIndex scalar is read. In
a 'busy' table, this may result in row creation attempts failing and
agents having to re-read the scalar before making a second row
creation attempt. The desire to avoid this issue is in opposition to
the desire to avoid lacunae.
Nadeau, et al. Informational [Page 11]
RFC 4221 MPLS Management Overview November 2005
5.4. Notifications
MPLS-LSR-STD-MIB can issue two notifications (if notifications are
enabled).
- mplsXCUp reports when a cross-connect becomes active.
- mplsXCDown reports when a cross-connect becomes
inactive.
5.5. Dependencies between MIB Module Tables
The tables in MPLS-LSR-STD-MIB are related as shown on the diagram
below. The arrows indicate a reference from one table to another.
Note that the various MIB tables contain two instances of pointers to
external tables that are not currently defined. Entries in an
external Traffic Parameters Table (external_Traffic_Table) are
pointed to using RowPointers from the mplsInSegmentTable
(mplsInSegmentTrafficParamPtr) and from the mplsOutSegmentTable
(mplsOutSegmentTrafficParamPtr) to allow representation of the
traffic parameters for the MPLS segment. Alternatively, the pointers
may indicate an entry in the Tunnel Resource Table
(mplsTunnelResourceTable) in MPLS-TE-STD-MIB. Similarly, an external
label table may be used to store label values if, for some reason,
they are not stored in place within the LSR MIB tables. This might
occur if extra per-label space information needs to be stored, and it
paves the way for GMPLS where labels cannot always be stored in a
32-bit value. RowPointers are used from the mplsInSegmentTable
(mplsInSegmentLabelPtr), the mplsOutSegmentTable
(mplsOutSegmentTopLabelPtr), and from the mplsLabelStackTable
(mplsLabelStackLabelPtr).
Nadeau, et al. Informational [Page 12]
RFC 4221 MPLS Management Overview November 2005
mplsInterfacePerfTable
^
|
V
mplsInterfaceTable
^ ^
mplsInSegmentMapTable | | mplsLabelStackTable
| | | ^ |
| +----+ +----+ | |
| | | | |
| | external_Traffic_Table | | |
| | ^ ^ | | |
V | | | | | |
mplsInSegmentTable mplsOutSegmentTable |
| ^ ^ ^ ^ | |
| | | | | | V
+------+ | +----> mplsXCTable <----+ | +--+
| V V |
| mplsInSegmentPerfTable mplsOutSegmentPerfTable |
| |
+--------------> external_Label_Table <-------------+
6. Tables, Scalars, and Notifications in the LDP MIB
6.1. MIB Modules
The MIB document for LDP contains four MIB modules. This structure
makes it easier for an implementation to select only those modules
that are relevant to it. The MIB Modules are MPLS-LDP-STD-MIB,
MPLS-LDP-GENERIC-STD-MIB, MPLS-LDP-ATM-STD-MIB, and MPLS-LDP-FRAME-
RELAY-STD-MIB.
MPLS-LDP-STD-MIB defines objects that are specific to LDP without any
Layer 2 objects. MPLS-LDP-GENERIC-STD-MIB defines Layer 2 Per
Platform Label Space objects for use with MPLS-LDP-STD-MIB and for
use on Ethernet. MPLS-LDP-ATM-STD-MIB defines Layer 2 Asynchronous
Transfer Mode (ATM) objects for use with MPLS-LDP-STD-MIB. MPLS-
LDP-FRAME-RELAY-STD-MIB defines Layer 2 FRAME-RELAY objects for use
with MPLS-LDP-STD-MIB.
The MPLS-LDP-STD-MIB module provides the core support and is
typically supported along with at least one of the Layer 2 MIB
modules.
Nadeau, et al. Informational [Page 13]
RFC 4221 MPLS Management Overview November 2005
6.2. Tables
The tables in the LDP MIB for configuring the LDP behavior of an LSR
are as follows.
- The LDP Entity Table (mplsLdpEntityTable) provides a way to
configure the LSR for using LDP. There must be at least one LDP
Entity for the LSR to support LDP. Each entry/row in this table
represents a single LDP Entity.
- Several tables exist to help configure LDP's use of labels. These
are spread through the MIB modules described in the previous
section. They are: mplsLdpEntityGenLRTable,
mplsLdpEntityAtmParmsTable and mplsLdpEntityAtmLRTable,
mplsLdpEntityFrameRelayParmsTable and mplsLdpEntityFrLRTable.
They are used to configure generic, ATM, and Frame Relay labels as
their names suggest.
- The LDP Peer Table (mplsLdpPeerTable) is a read-only table that
contains information about LDP Peers known to LDP Entities.
- The LDP Hello Adjacencies Table (mplsLdpHelloAdjacencyTable) is a
table of all adjacencies between all LDP Entities and all LDP
Peers.
- Several tables exist to monitor and control LDP sessions. The LDP
Session Table (mplsLdpSessionTable) represents sessions between an
LDP Entity and a Peer. mplsLdpAtmSesTable and
mplsLdpFrameRelaySesTable contain session information specific to
ATM.
- The MPLS LDP Session Peer Address Table (mplsLdpSesPeerAddrTable)
stores addresses learned after session initialization via Address
Message advertisement.
- The LDP FEC Table (mplsFecTable) represents FEC (Forwarding
Equivalence Class) information that may be in use on one or more
LSPs. The LDP LSP FEC Table (mplsLdpLspFecTable) shows the FECs
associated with each LSP.
- MPLS-LDP-STD-MIB has a mapping table (mplsLdpLspTable) that maps
the LDP MIB's representation of LDP sessions to the underlying LSR
MIB's representation of the LSPs created by these sessions, by
pointing to mplsInSegmentTable, mplsOutSegmentTable, and
mplsXCTable, respectively.
Nadeau, et al. Informational [Page 14]
RFC 4221 MPLS Management Overview November 2005
- Statistics may be gathered through the LDP Entity Statistics Table
(mplsLdpEntityStatsTable) and the LDP Session Statistics Table
(mplsLdpSesStatsTable).
6.3. Scalars
Where tables in the MIB modules have arbitrary indexes, scalars are
provided to supply the next available index. This applies to
mplsLdpEntityTable and mplsFecTable.
Two scalars exist to configure the LSR. The LSR ID is set in
mplsLdpLsrId, and the loop detection capabilities are reported in
mplsLdpLsrLoopDetectionCapable.
6.4. Notifications
MPLS-LDP-STD-MIB defines four notifications that a device can issue.
- mplsLdpInitSesThresholdExceeded is reported when the number of
Session Initialization messages exceeds a configured threshold.
- mplsLdpPVLMismatch is issued if the Path Vector Limit for a
configured Entity and Peer do not match.
- mplsLdpSessionUp and mplsLdpSessionDown report the transition of
Session state.
No scalar object is provided to enable and disable notifications from
MPLS-LDP-STD-MIB. Instead, the implementer is referred to [RFC3413].
6.5. Dependencies between MIB Module Tables
The many tables in the four LDP MIB modules are related as shown on
the diagram below. The arrows indicate a reference from one table to
another. Note that in many cases the reference is through an
augmentation of the referenced table.
Nadeau, et al. Informational [Page 15]
RFC 4221 MPLS Management Overview November 2005
mplsLdpEntityGenLRTable ------------->+
mplsLdpEntityAtmParmsTable ---------->+
mplsLdpEntityAtmLRTable ------------->+
mplsLdpEntityFrameRelayParmsTable --->+
mplsLdpEntityFrLRTable -------------->+
mplsLdpEntityStatsTable ------------->+
|
mplsLdpHelloAdjacencyTable |
| |
| mplsLdpEntityTable <--+
| ^ ^
V | |
mplsLdpPeerTable <-+- mplsLdpSesPeerAddrTable
^ |
| V
mplsLdpSessionTable
^ ^
| |
mplsLdpSesStatsTable ------+ +-- mplsLdpLspFecTable
mplsLdpAtmSesTable --------+ | | |
mplsLdpFrameRelaySesTable--+ | | V
| | mplsFecTable
| V
+-- mplsLdpLspTable
7. Tables, Scalars, and Notifications in MPLS-TE-STD-MIB
7.1. Tables
MPLS-TE-STD-MIB contains the following tables.
- The Tunnel Table (mplsTunnelTable) is used to configure and report
MPLS tunnels. Note that reporting of tunnels in this table at
transit LSRs is optional.
Entries in mplsTunnelTable are indexed by four objects. The
source and destination LSR IDs give context to the entry, and an
index (mplsTunnelIndex) identifies the tunnel itself. However,
the fourth index (mplsTunnelInstance) may give rise to some
confusion since its usage is not clearly explained.
The description says: "Uniquely identifies an instance of a
tunnel. It is useful to identify multiple instances of tunnels
for the purposes of backup and parallel tunnels." In the case of
backup tunnels, multiple instances of the same tunnel may be
defined, but only one is active at any time. Different instances
may have different properties (such as explicit routes), and one
instance may be set up to protect against failure of another.
Nadeau, et al. Informational [Page 16]
RFC 4221 MPLS Management Overview November 2005
Parallel tunnels may be used to provide load sharing or
protection.
The mplsTunnelInstancePriority object is used to indicate the
precedence of tunnels with the same LSR IDs and mplsTunnelIndex
value. The mplsTunnelPrimaryInstance object gives a quick
reference back to the preferred instance of the tunnel.
The mplsTunnelIndex value is typically signaled as the Tunnel ID,
and the mplsTunnelInstance as the LSP ID, in protocols where both
fields exist. In protocols where there is only one identifying
index (usually known as the LSP ID), only the mplsTunnelIndex is
signaled.
- The Resource Table (mplsTunnelResourceTable) is used to configure
resources to be requested on this tunnel. The CRLDP resource
table (mplsTunnelCRLDPResTable) is used to request additional
resource details that are specific to tunnels signaled using CR-
LDP.
- The routes requested, computed, and actually used for a tunnel are
found in the Tunnel Hop Table (mplsTunnelHopTable), Tunnel
Computed Hop Table (mplsTunnelCHopTable), and Tunnel Actual Hop
Table (mplsTunnelARHopTable).
- Statistics about the performance of tunnels may be gathered
through the Tunnel Performance Table (mplsTunnelPerfTable).
7.2. Scalars
Where tables in the MIB module have arbitrary indexes, scalars are
provided to supply the next available index. This applies to
mplsTunnelTable, mplsTunnelResourceTable, and mplsTunnelHopTable.
Two scalars exist to configure the support for MPLS tunnels on the
LSR. mplsTunnelTEDistProto lists the signaling methods and protocols
supported. mplsTunnelMaxHops defines the size of route that may be
configured on the LSR.
Two further scalars enhance the statistics on the LSR by counting the
number of configured (mplsTunnelConfigured) and active
(mplsTunnelActive) tunnels.
The scalar mplsTunnelNotificationMaxRate is used to control the rate
at which notifications are issued from MPLS-TE-STD-MIB. A rate of
zero means that notifications must not be issued. If notifications
Nadeau, et al. Informational [Page 17]
RFC 4221 MPLS Management Overview November 2005
would be generated faster than the configured rate, an implementation
may choose to discard notifications or to queue them for distribution
at a quieter time.
7.3. Notifications
MPLS-TE-STD-MIB defines four notifications that a device can issue.
The rate of dispatch of notifications is controlled as described in
the previous section.
- mplsTunnelUp and mplsTunnelDown report the transition of Tunnel
state.
- Rerouting and re-optimization of Tunnels paths are reported by
mplsTunnelRerouted and mplsTunnelReoptimized.
7.4. Dependencies between MIB Module Tables
The tables in MPLS-TE-STD-MIB are related as shown on the diagram
below. The arrows indicate a reference from one table to another.
mplsTunnelPerfTable
^
|
V
mplsTunnelTable
| |
V |
mplsTunnelResourceTable +--> mplsTunnelHopTable
^ |
| +--> mplsTunnelCHopTable
V |
mplsTunnelCRLDPResTable +--> mplsTunnelARHopTable
8. Tables, Scalars, and Notifications in MPLS-FTN-STD-MIB
8.1. Tables
MPLS-FTN-STD-MIB contains the following tables.
- The FEC-to-NHLFE Table (mplsFTNTable) defines the FEC to NHLFE
rules to be applied to incoming packets, and the actions to be
taken on matching packets.
- The FEC-to-NHLFE Mapping Table (mplsFTNMapTable) provides the
capability to activate FTN rules defined in the mplsFTNTable on
specific interfaces in the system.
Nadeau, et al. Informational [Page 18]
RFC 4221 MPLS Management Overview November 2005
- Performance statistics for FTN rules are found in the
mplsFTNPerfTable.
8.2. Scalars
This MIB module contains the scalars mplsFTNTableLastChanged and
mplsFTNMapTableLastChanged to indicate the last time an object
changed in mplsFTNTable and mplsFTNMapTable, respectively. Another
scalar, mplsFTNIndexNext, is used to supply the next valid index for
creating new conceptual rows in mplsFTNTable.
8.3. Notifications
There are no notifications in this MIB module.
8.4. Dependencies between MIB Module Tables
The tables in MPLS-FTN-STD-MIB are related as shown on the diagram
below. The arrows indicate a reference from one table to another.
mplsFTNTable
^
|
mplsFTNMapTable
^
|
mplsFTNPerfTable
9. Tables and Objects in TE-LINK-STD-MIB
9.1. Tables
TE-LINK-STD-MIB contains the following tables.
- The TE link table (teLinkTable) is used to specify TE links,
including bundled links, and their generic traffic-engineering
parameters.
- The TE link descriptor table (teLinkDescriptorTable) is used to
list the TE link descriptors.
- The shared risk link group (SRLG) table (teLinkSrlgTable) is used
to specify the SRLGs associated with TE links.
- The TE link bandwidth table (teLinkBandwidthTable) is used to
report priority-based bandwidth values associated with TE links.
Nadeau, et al. Informational [Page 19]
RFC 4221 MPLS Management Overview November 2005
- The component link table (componentLinkTable) is used to identify
the data-bearing component links that are associated with the TE
links and specify the data-bearing link generic traffic
engineering parameters.
- The component link descriptor table (componentLinkDescriptorTable)
is used to list the data-bearing component link descriptors.
- The component link bandwidth table (componentLinkBandwidthTable)
is used to report priority-based bandwidth values associated with
data-bearing component links.
9.2. Scalars
There are no scalars in this MIB module.
9.3. Notifications
There are no notifications in this MIB module.
9.4. Dependencies between MIB Module Tables
The tables in TE-LINK-STD-MIB are related as shown on the diagram
below. The arrows indicate a reference from one table to another.
Note that many of the associations between tables are through a
common index that is the ifIndex of the related interface.
teLinkTable
^
|
teLinkDescriptorTable ---+
|
teLinkSrlgTable ---------+
|
teLinkBandwidthTable ----+
componentLinkTable
^
|
componentLinkDescriptorTable ---+
|
componentLinkBandwidthTable ----+
Nadeau, et al. Informational [Page 20]
RFC 4221 MPLS Management Overview November 2005
10. Table Dependencies between MPLS MIB Modules
Section 4.11 gave an overview of how the MPLS MIB modules are
related. Now that the tables in the MIB modules have been
introduced, it is possible to give a more detailed diagram of these
relationships.
MPLS-TC-STD-MIB is left off the diagram because many of the MIB
module tables use textual conventions from that MIB module.
mplsLsrXCTable mplsLsrInSegmentTable
^ ^
| |
+---- mplsLdpLspTable
| |
mplsTunnelTable ------+ V
^ | mplsLsrOutSegmentTable
| |
mplsFTNTable ---------+
11. A Note on Interfaces
The Interfaces Group of IF-MIB [RFC2863] defines generic managed
objects for managing interfaces. The MPLS MIB modules make
references to interfaces so that it can be clearly determined where
the procedures managed by the MIB modules should be performed.
Additionally, the MPLS MIB modules (notably MPLS-TE-STD-MIB and TE-
LINK-STD-MIB) utilize interface stacking within the Interface Group.
11.1. MPLS Tunnels as Interfaces
MPLS-TE-STD-MIB builds on the concept of managing MPLS Tunnels as
logical interfaces. [RFC2863] states that the interfaces table
(ifTable) contains information on the managed resource's interfaces,
and that each sub-layer below the internetwork layer of a network
interface is considered an interface. Thus, an MPLS Tunnel managed
as an interface is represented as an entry in the ifTable. The
interrelation of entries in the ifTable is defined by the Interfaces
Stack Group defined in [RFC2863].
When using MPLS Tunnels as interfaces, the interface stack table
might appear as follows:
Nadeau, et al. Informational [Page 21]
RFC 4221 MPLS Management Overview November 2005
+------------------------------------------------+
| MPLS tunnel interface ifType = mplsTunnel(150) |
+------------------------------------------------+
| MPLS interface ifType = mpls(166) |
+------------------------------------------------+
| Underlying layer |
+------------------------------------------------+
In the diagram above, "Underlying layer" refers to the ifIndex of any
interface type for which MPLS internetworking has been defined.
Examples include ATM, Frame Relay, and Ethernet.
A detailed listing of the mapping between ifTable objects and their
use for MPLS Tunnels is given in [TEMIB]. A few key objects are
listed here to provide an overview of the concepts.
Each MPLS tunnel is represented by an entry in the ifTable. Each
tunnel is therefore assigned a unique ifIndex.
The type of an interface represented by an entry in the ifTable is
indicated by the ifType object. The value that is allocated to
identify an MPLS tunnel is 150.
The ifOperStatus object reflects the actual operational status of the
MPLS tunnel and may be mapped from the mplsTunnelOperStatus object.
It may be considered convenient and good management to set the ifName
object to reflect the name of the MPLS tunnel as contained in the
mplsTunnelName object.
11.2. Application of the Interfaces Group to TE Links
TE-LINK-STD-MIB also uses interface stacking to manage TE Link
interfaces as logical interfaces. The TE Link interface is
represented as an entry in the ifTable. The interrelation of entries
in the ifTable is defined by Interfaces Stack Group defined in
[RFC2863]. When using TE Link interfaces, the interface stack table
might appear as follows:
Nadeau, et al. Informational [Page 22]
RFC 4221 MPLS Management Overview November 2005
+-------------------------------------------------------------------+
| MPLS interface ifType = mpls(166) |
| ifIndex = 1 |
+-------------------------------------------------------------------+
| TE link (bundled link) ifType = teLink(200) |
| ifIndex = 2 |
+--------------------------------+-+--------------------------------+
| TE link ifType = teLink(200) | | TE link ifType = teLink(200) |
| ifIndex = 3 | | ifIndex = 4 |
+--------------------------------+ +--------------------------------+
| Component link | | Component link |
| ifType = opticalTransport(196) | | ifType = opticalTransport(196) |
| ifIndex = 5 | | ifIndex = 6 |
+--------------------------------+ +--------------------------------+
In the above diagram, "opticalTransport" is an example of an
underlying physical interface: in this case an optical transport
interface. TE link management and bundling can be seen in the levels
of interface stacking. Two TE links are defined, each managing an
optical transport link. These two TE links are combined into a
bundle, which is managed as a single TE link interface. This TE Link
interface supports MPLS and is presented as an MPLS interface.
A detailed listing of the mapping between ifTable objects and their
use for TE Links is given in [TELMIB]. A few key objects are listed
here to provide an overview of the concepts.
Each TE Link interface is represented by a separate entry in the
ifTable, with a unique ifIndex.
The type of an interface represented by an entry in the ifTable is
indicated by the ifType object. The value that is allocated to
identify a TE Link is 200.
11.3. References to Interface MIB Objects from MPLS MIB Modules
MPLS-TE-STD-MIB contains two objects that reference the management of
an MPLS tunnel as an interface. mplsTunnelIsIf is a TruthValue that
indicates whether the tunnel is present in the ifTable. If the
tunnel is managed as an interface, the mplsTunnelIfIndex object
contains the ifIndex that identifies the corresponding entry in the
ifTable.
MPLS-LSR-STD-MIB includes a table (mplsInterfaceTable) for
configuring the support for MPLS on specific interfaces. A
conceptual row in this table is created automatically by an LSR for
every interface that is capable of and configured for support of
MPLS. A conceptual row in this table will exist if and only if a
Nadeau, et al. Informational [Page 23]
RFC 4221 MPLS Management Overview November 2005
corresponding entry in ifTable exists with ifType = mpls(166). The
fate of the entries in the two tables are closely linked so that if
the entry in the ifTable is operationally disabled, the entry in
mplsInterfaceTable is deleted. During the life of an entry in
mplsInterfaceTable, a corresponding entry is managed in
mplsInterfacePerfTable to show performance counters for the MPLS-
capable interface.
The ifIndex that identifies MPLS-capable interfaces also plays an
important indexing role in MPLS-LSR-STD-MIB. In-segments (that is,
incoming LSP labels) are represented in mplsInSegmentTable, which is
indexed by the mplsInSegmentIfIndex and mplsInSegmentLabel objects.
mplsInSegmentIfIndex is set to the ifIndex of the incoming MPLS-
capable interface. mplsInSegmentLabel identifies the incoming MPLS
label. Note that the corresponding mplsOutSegmentTable contains an
mplsOutSegmentIfIndex object to identify the outgoing MPLS-capable
interface, but that this does not form part of the index of the
table.
MPLS-LDP-STD-MIB uses ifIndex extensively to identify the interface
over which MPLS is active.
Within MPLS-FTN-STD-MIB, mplsFTNMapTable maps entries in mplsFTNTable
to interfaces on which mplsFTNTable entries should be activated.
Interfaces are identified using their ifIndex values.
12. Management Options
It is not the intention of this document to provide instructions or
advice to implementers of Management Stations, Management Agents, or
managed entities. It is, however, useful to make some observations
about how the MIB modules described above might be used to manage
MPLS systems.
All MPLS LSPs may appear in MPLS-LSR-STD-MIB. At transit nodes, they
are seen as full cross-connects between incoming labels on incoming
interfaces and outgoing labels on outgoing interfaces. At ingress or
egress points, the cross-connections are unbalanced having spoof
upstream or downstream legs, respectively.
Split and merge points of LSPs may be represented as more complex
cross-connects in MPLS-LSR-STD-MIB. Similarly, bidirectional LSPs
can be represented by using the same cross-connect index for each of
the forward and reverse cross-connections.
The modules in the LDP MIB are intended solely for use with LDP and
CR-LDP. LSPs that are signaled through other means may conveniently
be stored in mplsLdpLspTable for consistency with LSPs set up using
Nadeau, et al. Informational [Page 24]
RFC 4221 MPLS Management Overview November 2005
LDP, but there is little further value to this because the table
gives only pointers into MPLS-LSR-STD-MIB. If, however, the LSPs are
established with associated FECs using some signaling method other
than LDP (for example, BGP), it may be advantageous to use
mplsLdpLspTable, mplsFecTable, and mplsLdpLspFecTable to correlate
the LSPs.
Note that if CR-LDP is the signaling protocol, there is no
requirement to use the LSP-related tables in the LDP MIB since the
LSP will be adequately represented in MPLS-TE-MIB and MPLS-LSR-STD-
MIB.
MPLS tunnels may be represented in MPLS-TE-STD-MIB with their cross-
connects indicated in MPLS-LSR-STD-MIB. Tunnels are often (although
not always) set up with a series of constraints that may be
represented in MPLS-TE-STD-MIB. Note that a distinguishing feature
of a tunnel is that it has an ingress and an egress, where LSPs
established through LDP may be end-to-end or may be hop-by-hop.
All LSPs (tunnels and non-tunnels) may be established as a result of
signaling protocols already defined or for future study. In
addition, LSPs may be set up manually by issuing configuration
commands to each of the LSRs on the LSP. These commands may utilize
SNMP by performing SET operations to the MIB module tables and
objects described here. Alternatively, configuration may be through
some non-standard interface such as a Command Line or a Graphical
User Interface. Such configured LSPs may also be represented in the
MIB module tables.
Do not be misled by considerations of the "permanence" of LSPs when
deciding which tables of which MIB modules to use. An MPLS tunnel
may have a very long life expectancy if it is set up by an amnesiac
user. Otherwise, it may have a very short lifetime if it is
automatically provisioned to satisfy on-demand traffic requirements.
Similarly, an LSP established in response to a routing protocol
(sometimes known as a hop-by-hop LSP) may be equally stable or
unstable.
13. Related IETF MIB Modules
This section describes the broad interactions between MIB modules
produced by the PWE3, PPVPN, and CCAMP working groups and the MPLS
MIB modules. This information is provided as background and is not
central to this document.
Nadeau, et al. Informational [Page 25]
RFC 4221 MPLS Management Overview November 2005
13.1. PWE3 Working Group MIB Modules
The PWE3 working group has produced a document [PWE3FW] that includes
a description of the framework for MIB modules within PWE3 operation.
Since the PWE3 architecture includes the use of MPLS as an emulated
service and as a PSN service, the MPLS MIB modules described above
may be leveraged. The PWE3 framework document describes the
interactions between the MPLS MIB modules and the PWE3 MIB modules.
13.2. PPVPN Working Group MIB Modules
At present, the PPVPN working group has not included a discussion of
how the MPLS MIB modules interact with the MIB modules being produced
by that working group. The authors of this document hope to make a
forthcoming addition to the PPVPN framework document [PPVPNFW]
detailing these interactions. At the moment, there are two MIB
modules, [VPNMIB] and [VPNTCMIB], which are discussed next.
13.2.1. PPVPN-MPLS-VPN-STD-MIB
PPVPN-MPLS-VPN-STD-MIB describes managed objects that are used to
model and manage RFC2547bis MPLS VPNs [RFC2547Bis]. This MIB module
contains tables that model virtual routing forwarding entries (VRFs),
as well as the interfaces associated with those VRFs.
13.2.1.1. Position in the OID Tree
transmission -- RFC 2578 [RFC2578]
|
+- vpnMIB -- PPVPN-MPLS-VPN-STD-MIB
13.2.1.2. Dependencies
This MIB module currently has no direct dependencies on any of the
MPLS MIB modules. This MIB module models MPLS VPN interfaces as
entries in the Interfaces MIB's Interfaces Table (ifTable). This MIB
module may be modified in the future to import textual conventions
from MPLS-TC-STD-MIB.
A specific textual conventions MIB module [VPNTCMIB] defines textual
conventions that are imported into PPVPN-MPLS-VPN-STD-MIB.
13.3. CCAMP Working Group MIB Modules
The CCAMP working group is developing MIB modules in support of GMPLS
that interact directly with the MPLS MIB modules. Along with any MIB
modules produced by the CCAMP working group, a separate CCAMP-
Nadeau, et al. Informational [Page 26]
RFC 4221 MPLS Management Overview November 2005
specific Management Framework document is expected to be issued
describing the relationship between these MIB modules and the
existing MPLS (and other) MIB modules.
14. Traffic Engineering Working Group TE MIB
The TEWG has produced a traffic engineering MIB (TE-MIB) [TEWGMIB]
containing objects for monitoring traffic-engineered tunnels at their
ingress points.
In many senses TE-MIB contains the same information as MPLS-TE-STD-
MIB. Both MIB modules can be used to monitor MPLS tunnels; however,
TE-MIB is minimalistic and caters best to TE tunnels as tunnels, at
the expense of not having many advanced features of MPLS-TE-STD-MIB,
whereas MPLS-TE-STD-MIB can deconstruct tunnels into hop-by-hop
cross-connects, at the expense of more complexity.
The TE-MIB module imports textual conventions from the MPLS-TC-STD-
MIB module and therefore is dependent on that document.
14.1. Choosing between TE MIB Modules
TE-MIB is a flexible MIB module designed to manage traffic
engineering tunnels regardless of the implementation technology.
This flexibility and a focus on simplicity lead to some compromises.
- Some MPLS configuration parameters are left out. For example, the
resource management in TE-MIB is confined to bandwidth, so missing
the full IntServ control.
- Other TE-MIB parameters are present but with only limited options;
for example, the ability to configure different label distribution
methods per LSP.
Extensibility of TE-MIB to related concepts (such as DiffServ and
Fast Reroute) and integrations with other MIB modules (such as that
in MPLS-LSR-STD-MIB) are not work items at the time of writing. The
MPLS MIB modules are more closely integrated as described in this
document.
Write/create access to TE-MIB is only available at the ingress, where
it can be used to configure an ingress to signal a tunnel with
constraints. It cannot be used to configure hop-by-hop cross-
connects to build a tunnel.
The purpose of TE-MIB module is to allow a Management Agent to
configure tunnels, and to inspect and monitor all tunnels (however
created) at their ingress points. It does not provide information
Nadeau, et al. Informational [Page 27]
RFC 4221 MPLS Management Overview November 2005
about tunnels at any other point in the network (that is, at transit
or egress nodes). This module can be used, for example, to configure
the constraints of a tunnel, whereupon the ingress would compute the
tunnel path and signal it. The MIB module can then be used at the
ingress to monitor the tunnel's path(s), their status, and the
tunnel's uptime and counters. This MIB module is not designed to
configure hop-by-hop cross-connects to build a tunnel.
15. Security Considerations
This document describes the interrelationships amongst the different
MIB modules relevant to MPLS management and as such does not have any
security implications in and of itself.
Each specific MIB document specifies specific MIB objects, and such a
document must provide a proper security considerations section that
explains the security aspects of those objects.
The attention of readers is particularly drawn to the security
implications of making MIB objects available for create or write
access through an access protocol such as SNMP. SNMPv1 by itself is
an insecure environment. Even if the network itself is made secure
(for example, by using IPSec), there is no control over who on the
secure network is allowed to access and GET (read) the objects in
this MIB. It is recommended that the implementers consider the
security features as provided by the SNMPv3 framework. Specifically,
the use of the User-based Security Model STD 62, RFC 3414 [RFC3414],
and the View-based Access Control Model STD 62, RFC 3415 [RFC3415],
is recommended.
It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB is properly
configured to give access to only those objects, and to those
principals (users) that have legitimate rights to access them.
16. Acknowledgements
Many small pieces of text in this document have been borrowed from
the documents that define the MIB modules described here. The
authors would like to express appreciation to all who worked on those
MIB documents.
Thanks also to all those who attended the November 2002 MPLS MIB open
meeting and gave constructive feedback, and in particular to Sharon
Chisholm for her thoughts on Management Options.
Thanks to Kireeti Kompella for revising the text on TE-MIB.
Nadeau, et al. Informational [Page 28]
RFC 4221 MPLS Management Overview November 2005
Without the consistent pressure and encouragement from Bert Wijnen,
this document would not have been written.
17. Normative References
[FTNMIB] Nadeau, T., Srinivasan, C., and A. Viswanathan,
"Multiprotocol Label Switching (MPLS) Forwarding
Equivalence Class To Next Hop Label Forwarding Entry
(FEC-To-NHLFE) Management Information Base (MIB)", RFC
3814, June 2004.
[LDPMIB] Cucchiara, J., Sjostrand, H., and J. Luciani,
"Definitions of Managed Objects for the Multiprotocol
Label Switching (MPLS), Label Distribution Protocol
(LDP)", RFC 3815, June 2004.
[LSRMIB] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label Switching
Router (LSR) Management Information Base (MIB)", RFC
3813, June 2004.
[RFC2863] McCloghrie, K. and F. Kastenholtz, "The Interfaces
Group MIB ", RFC 2863, June 2000.
[RFC3289] Baker, F., Chan, K., and A. Smith, "Management
Information Base for the Differentiated Services
Architecture", RFC 3289, May 2002.
[TCMIB] Nadeau, T. and J. Cucchiara, "Definitions of Textual
Conventions (TCs) for Multiprotocol Label Switching
(MPLS) Management", RFC 3811, June 2004.
[TELMIB] Dubuc, M., Dharanikota, S., Nadeau, T., J. Lang,
"Traffic Engineering Link Management Information Base",
RFC 4220, November 2005.
[TEMIB] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering (TE) Management Information Base (MIB)",
RFC 3812, June 2004.
Nadeau, et al. Informational [Page 29]
RFC 4221 MPLS Management Overview November 2005
18. Informative References
[PPVPNFW] Callon, R. and M. Suzuki, "A Framework for Layer 3
Provider-Provisioned Virtual Private Networks
(PPVPNs)", RFC 4110, July 2005.
[PWE3FW] Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-
to-Edge (PWE3) Architecture", RFC 3985, March 2005.
[RFC2026] Bradner, S., "The Internet Standards Process --
Revision 3", BCP 9, RFC 2026, October 1996.
[RFC2547Bis] Rosen, E., et al., "MPLS/BGP VPNs", Work in Progress,
October 2002.
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Structure of Management Information Version 2
(SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579,
April 1999.
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Conformance Statements for SMIv2", STD 58, RFC 2580,
April 1999.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC 3031,
January 2001.
[RFC3036] Andersson, L., Doolan, P., Feldman, N., Fredette, A.,
and B. Thomas, "LDP Specification", RFC 3036, January
2001.
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3413] Levi, D., Meyer, P., and B. Stewart, "Simple Network
Management Protocol (SNMP) Applications", STD 62, RFC
3413, December 2002.
[RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security
Model (USM) for version 3 of the Simple Network
Management Protocol (SNMPv3)", STD 62, RFC 3414,
December 2002.
Nadeau, et al. Informational [Page 30]
RFC 4221 MPLS Management Overview November 2005
[RFC3415] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
Access Control Model (VACM) for the Simple Network
Management Protocol (SNMP)", STD 62, RFC 3415, December
2002.
[TEWGMIB] Kompella, K., "A Traffic Engineering (TE) MIB", RFC
3970, January 2005.
[VPNMIB] Nadeau, T., et al., "MPLS/BGP Virtual Private Network
Management Information Base Using SMIv2", Work in
Progress, November 2002.
[VPNTCMIB] Schliesser, B. and T. Nadeau, "Definition of Textual
Conventions for Provider Provisioned Virtual Private
Network (PPVPN) Management", Work in Progress, November
2002.
Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
1414 Massachusetts Ave.
Boxborough, MA 01719
EMail:
[email protected]
Cheenu Srinivasan
Bloomberg L.P.
731 Lexington Avenue
New York, NY 10022
Phone: (212) 617-3682
EMail:
[email protected]
Adrian Farrel
Old Dog Consulting
Phone: +44 (0) 1978 860944
EMail:
[email protected]
Nadeau, et al. Informational [Page 31]
RFC 4221 MPLS Management Overview November 2005
Full Copyright Statement
Copyright (C) The Internet Society (2005).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
[email protected].
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Nadeau, et al. Informational [Page 32]
