Network Working Group M. Shand
Request for Comments: 3847 L. Ginsberg
Category: Informational Cisco Systems
July 2004
Restart Signaling for
Intermediate System to Intermediate System (IS-IS)
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2004). All Rights Reserved.
Abstract
This document describes a mechanism for a restarting router to signal
to its neighbors that it is restarting, allowing them to reestablish
their adjacencies without cycling through the down state, while still
correctly initiating database synchronization.
This document additionally describes a mechanism for a restarting
router to determine when it has achieved LSP database synchronization
with its neighbors and a mechanism to optimize LSP database
synchronization, while minimizing transient routing disruption when a
router starts.
Shand & Ginsberg Informational [Page 1]
RFC 3847 Restart signaling for IS-IS July 2004
Table of Contents
1. Conventions used in this Document. . . . . . . . . . . . . . . 2
2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Approach . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1. Timers . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2. Restart TLV. . . . . . . . . . . . . . . . . . . . . . . 5
3.2.1. Use of RR and RA Bits. . . . . . . . . . . . . . 6
3.2.2. Use of SA Bit. . . . . . . . . . . . . . . . . . 7
3.3. Adjacency (re)Acquisition. . . . . . . . . . . . . . . . 8
3.3.1. Adjacency Reacquisition During Restart . . . . . 8
3.3.2. Adjacency Acquisition During Start . . . . . . . 10
3.3.3. Multiple Levels. . . . . . . . . . . . . . . . . 12
3.4. Database Synchronization . . . . . . . . . . . . . . . . 12
3.4.1. LSP Generation and Flooding and SPF Computation. 13
3.4.1.1. Restarting. . . . . . . . . . . . . . . 13
3.4.1.2. Starting. . . . . . . . . . . . . . . . 15
4. State Tables . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1. Running Router . . . . . . . . . . . . . . . . . . . . . 16
4.2. Restarting Router. . . . . . . . . . . . . . . . . . . . 17
4.3. Starting Router. . . . . . . . . . . . . . . . . . . . . 18
5. Security Considerations. . . . . . . . . . . . . . . . . . . . 18
6. IANA Considerations. . . . . . . . . . . . . . . . . . . . . . 19
7. Normative References . . . . . . . . . . . . . . . . . . . . . 19
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 20
9. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 20
10. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 21
1. Conventions used in this Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC-2119 [3].
If the control and forwarding functions in a router can be maintained
independently, it is possible for the forwarding function state to be
maintained across a resumption of control function operations. This
functionality is assumed when the terms "restart/restarting" are used
in this document.
The terms "start/starting" are used to refer to a router in which the
control function has either commenced operations for the first time
or has resumed operations but the forwarding functions have not been
maintained in a prior state.
The terms "(re)start/(re)starting" are used when the text is
applicable to both a "starting" and a "restarting" router.
Shand & Ginsberg Informational [Page 2]
RFC 3847 Restart signaling for IS-IS July 2004
2. Overview
The Intermediate System to Intermediate System (IS-IS) routing
protocol [RFC 1195, ISO/IEC 10589] is a link state intra-domain
routing protocol. Normally, when an IS-IS router is restarted,
temporary disruption of routing occurs due to events in both the
restarting router and the neighbors of the restarting router.
The router which has been restarted computes its own routes before
achieving database synchronization with its neighbors. The results
of this computation are likely to be non-convergent with the routes
computed by other routers in the area/domain.
Neighbors of the restarting router detect the restart event and cycle
their adjacencies with the restarting router through the down state.
The cycling of the adjacency state causes the neighbors to regenerate
their LSPs describing the adjacency concerned. This in turn causes a
temporary disruption of routes passing through the restarting router.
In certain scenarios, the temporary disruption of the routes is
highly undesirable. This document describes mechanisms to avoid or
minimize the disruption due to both of these causes.
When an adjacency is reinitialized as a result of a neighbor
restarting, a router does three things:
1. It causes its own LSP(s) to be regenerated, thus triggering SPF
runs throughout the area (or in the case of Level 2, throughout
the domain).
2. It sets SRMflags on its own LSP database on the adjacency
concerned.
3. In the case of a Point-to-Point link, it transmits a (set of)
CSNP(s) over the adjacency.
In the case of a restarting router process, the first of these is
highly undesirable, but the second is essential in order to ensure
synchronization of the LSP database.
The third action above minimizes the number of LSPs which must be
exchanged and, if made reliable, provides a means of determining when
the LSP databases of the neighboring routers have been synchronized.
This is desirable whether the router is being restarted or not (so
that the overload bit can be cleared in the router's own LSP, for
example).
Shand & Ginsberg Informational [Page 3]
RFC 3847 Restart signaling for IS-IS July 2004
This document describes a mechanism for a restarting router to signal
that it is restarting to its neighbors, and allow them to reestablish
their adjacencies without cycling through the down state, while still
correctly initiating database synchronization.
This document additionally describes a mechanism for a restarting
router to determine when it has achieved LSP database synchronization
with its neighbors and a mechanism to optimize LSP database
synchronization and minimize transient routing disruption when a
router starts.
It is assumed that the three-way handshake [4] is being used on
Point-to-Point circuits.
3. Approach
3.1. Timers
Three additional timers, T1, T2, and T3 are required to support the
functionality defined in this document.
An instance of the timer T1 is maintained per interface, and
indicates the time after which an unacknowledged (re)start attempt
will be repeated. A typical value might be 3 seconds.
An instance of the timer T2 is maintained for each LSP database
present in the system, i.e., for a Level1/2 system, there will be an
instance of the timer T2 for Level 1 and an instance for Level 2.
This is the maximum time that the system will wait for LSPDB
synchronization. A typical value might be 60 seconds.
A single instance of the timer T3 is maintained for the entire
system. It indicates the time after which the router will declare
that it has failed to achieve database synchronization (by setting
the overload bit in its own LSP). This is initialized to 65535
seconds, but is set to the minimum of the remaining times of received
IIHs containing a restart TLV with the RA set and an indication that
the neighbor has an adjacency in the "UP" state to the restarting
router.
NOTE: The timer T3 is only used by a restarting router.
Shand & Ginsberg Informational [Page 4]
RFC 3847 Restart signaling for IS-IS July 2004
3.2. Restart TLV
A new TLV is defined to be included in IIH PDUs. The presence of
this TLV indicates that the sender supports the functionality defined
in this document and it carries flags that are used to convey
information during a (re)start. All IIHs transmitted by a router
that supports this capability MUST include this TLV.
Type 211
Length # of octets in the value field (1 to (3 + ID Length))
Value
No. of octets
+-----------------------+
| Flags | 1
+-----------------------+
| Remaining Time | 2
+-----------------------+
| Restarting Neighbor ID| ID Length
+-----------------------+
Flags (1 octet)
0 1 2 3 4 5 6 7
+--+--+--+--+--+--+--+--+
| Reserved |SA|RA|RR|
+--+--+--+--+--+--+--+--+
RR - Restart Request
RA - Restart Acknowledgement
SA - Suppress adjacency advertisement
(Note: Remaining fields are required when the RA bit is set)
Remaining Time (2 octets)
Remaining holding time (in seconds)
Restarting Neighbor System ID (ID Length octets)
The system ID of the neighbor to which an RA refers. Note:
Implementations based on earlier versions of this document may not
include this field in the TLV when the RA is set. In this case, a
router which is expecting an RA on a LAN circuit SHOULD assume that
the acknowledgement is directed at the local system.
Shand & Ginsberg Informational [Page 5]
RFC 3847 Restart signaling for IS-IS July 2004
3.2.1. Use of RR and RA Bits
The RR bit is used by a (re)starting router to signal to its
neighbors that a (re)start is in progress, that an existing adjacency
SHOULD be maintained even under circumstances when the normal
operation of the adjacency state machine would require the adjacency
to be reinitialized, to request a set of CSNPs, and to request
setting of the SRMflags.
The RA bit is sent by the neighbor of a (re)starting router to
acknowledge the receipt of a restart TLV with the RR bit set.
When the neighbor of a (re)starting router receives an IIH with the
restart TLV having the RR bit set, if there exists on this interface
an adjacency in state "UP" with the same System ID, and in the case
of a LAN circuit, with the same source LAN address, then,
irrespective of the other contents of the "Intermediate System
Neighbors" option (LAN circuits) or the "Point-to-Point Three-Way
Adjacency" option (Point-to-Point circuits):
a) the state of the adjacency is not changed. If this is the first
IIH with the RR bit set that this system has received associated
with this adjacency, then the adjacency is marked as being in
"Restart mode" and the adjacency holding time is refreshed -
otherwise the holding time is not refreshed. The "remaining time"
transmitted according to (b) below MUST reflect the actual time
after which the adjacency will now expire. Receipt of a normal
IIH with the RR bit reset will clear the "Restart mode" state.
This procedure allows the restarting router to cause the neighbor
to maintain the adjacency long enough for restart to successfully
complete while also preventing repetitive restarts from
maintaining an adjacency indefinitely. Whether an adjacency is
marked as being in "Restart mode" or not has no effect on
adjacency state transitions.
b) immediately (i.e., without waiting for any currently running timer
interval to expire, but with a small random delay of a few 10s of
milliseconds on LANs to avoid "storms") transmit over the
corresponding interface an IIH including the restart TLV with the
RR bit clear and the RA bit set, in the case of Point-to-Point
adjacencies having updated the "Point-to-Point Three-Way
Adjacency" option to reflect any new values received from the
(re)starting router. (This allows a restarting router to quickly
acquire the correct information to place in its hellos.) The
"Remaining Time" MUST be set to the current time (in seconds)
before the holding timer on this adjacency is due to expire. If
the corresponding interface is a LAN interface, then the
Restarting Neighbor System ID SHOULD be set to the System ID of
Shand & Ginsberg Informational [Page 6]
RFC 3847 Restart signaling for IS-IS July 2004
the router from whom the IIH with the RR bit set was received.
This is required to correctly associate the acknowledgement and
holding time in the case where multiple systems on a LAN restart
at approximately the same time. This IIH SHOULD be transmitted
before any LSPs or SNPs are transmitted as a result of the receipt
of the original IIH.
c) if the corresponding interface is a Point-to-Point interface, or
if the receiving router has the highest LnRouterPriority (with
highest source MAC address breaking ties) among those routers to
which the receiving router has an adjacency in state "UP" on this
interface whose IIHs contain the restart TLV, excluding
adjacencies to all routers which are considered in "Restart mode"
(note the actual DIS is NOT changed by this process), initiate the
transmission over the corresponding interface of a complete set of
CSNPs, and set SRMflags on the corresponding interface for all
LSPs in the local LSP database.
Otherwise (i.e., if there was no adjacency in the "UP" state to the
system ID in question), process the IIH as normal by reinitializing
the adjacency and setting the RA bit in the returned IIH.
3.2.2. Use of the SA Bit
The SA bit is used by a starting router to request that its neighbor
suppress advertisement of the adjacency to the starting router in the
neighbor's LSPs.
A router which is starting has no maintained forwarding function
state. This may or may not be the first time the router has started.
If this is not the first time the router has started, copies of LSPs
generated by this router in its previous incarnation may exist in the
LSP databases of other routers in the network. These copies are
likely to appear "newer" than LSPs initially generated by the
starting router due to the reinitialization of LSP fragment sequence
numbers by the starting router. This may cause temporary blackholes
to occur until the normal operation of the update process causes the
starting router to regenerate and flood copies of its own LSPs with
higher sequence numbers. The temporary blackholes can be avoided if
the starting router's neighbors suppress advertising an adjacency to
the starting router until the starting router has been able to
propagate newer versions of LSPs generated by previous incarnations.
When a router receives an IIH with the restart TLV having the SA bit
set, if there exists on this interface an adjacency in state "UP"
with the same System ID, and in the case of a LAN circuit, with the
same source LAN address, then the router MUST suppress advertisement
of the adjacency to the neighbor in its own LSPs. Until an IIH with
Shand & Ginsberg Informational [Page 7]
RFC 3847 Restart signaling for IS-IS July 2004
the SA bit clear has been received, the neighbor advertisement MUST
continue to be suppressed. If the adjacency transitions to the "UP"
state, the new adjacency MUST NOT be advertised until an IIH with the
SA bit clear has been received.
Note that a router which suppresses advertisement of an adjacency
MUST NOT use this adjacency when performing its SPF calculation. In
particular, if an implementation follows the example guidelines
presented in [2] Annex C.2.5 Step 0:b) "pre-load TENT with the local
adjacency database", the suppressed adjacency MUST NOT be loaded into
TENT.
3.3. Adjacency (Re)Acquisition
Adjacency (re)acquisition is the first step in (re)initialization.
Restarting and starting routers will make use of the RR bit in the
restart TLV, though each will use it at different stages of the
(re)start procedure.
3.3.1. Adjacency Reacquisition During Restart
The restarting router explicitly notifies its neighbor that the
adjacency is being reacquired, and hence that it SHOULD NOT
reinitialize the adjacency. This is achieved by setting the RR bit
in the restart TLV. When the neighbor of a restarting router
receives an IIH with the restart TLV having the RR bit set, if there
exists on this interface an adjacency in state "UP" with the same
System ID, and in the case of a LAN circuit, with the same source LAN
address, then the procedures described in 3.2.1 are followed.
A router that does not support the restart capability will ignore the
restart TLV and reinitialize the adjacency as normal, returning an
IIH without the restart TLV.
On restarting, a router initializes the timer T3, starts the timer T2
for each LSPDB, and for each interface (and in the case of a LAN
circuit, for each level) starts the timer T1 and transmits an IIH
containing the restart TLV with the RR bit set.
On a Point-to-Point circuit the restarting router SHOULD set the
"Adjacency Three-Way State" to "Init", because the receipt of the
acknowledging IIH (with RA set) MUST cause the adjacency to enter the
"UP" state immediately.
On a LAN circuit the LAN-ID assigned to the circuit SHOULD be the
same as that used prior to the restart. In particular, for any
circuits for which the restarting router was previously DIS, the use
of a different LAN-ID would necessitate the generation of a new set
Shand & Ginsberg Informational [Page 8]
RFC 3847 Restart signaling for IS-IS July 2004
of pseudonode LSPs, and corresponding changes in all the LSPs
referencing them from other routers on the LAN. By preserving the
LAN-ID across the restart, this churn can be prevented. To enable a
restarting router to learn the LAN-ID used prior to restart, the
LAN-ID specified in an IIH with RR set MUST be ignored.
Transmission of "normal" IIHs is inhibited until the conditions
described below are met (in order to avoid causing an unnecessary
adjacency initialization). Upon expiry of the timer T1, it is
restarted and the IIH is retransmitted as above.
When a restarting router receives an IIH a local adjacency is
established as usual, and if the IIH contains a restart TLV with the
RA bit set (and on LAN circuits with a Restart Neighbor System ID
which matches that of the local system), the receipt of the
acknowledgement over that interface is noted. When the RA bit is set
and the state of the remote adjacency is "UP", then the timer T3 is
set to the minimum of its current value and the value of the
"Remaining Time" field in the received IIH.
On a Point-to-Point link, receipt of an IIH not containing the
restart TLV is also treated as an acknowledgement, since it indicates
that the neighbor is not restart capable. However, since no CSNP is
guaranteed to be received over this interface, the timer T1 is
cancelled immediately without waiting for a complete set of CSNP(s).
Synchronization may therefore be deemed complete even though there
are some LSPs which are held (only) by this neighbor (see section
3.4). In this case we also want to be certain that the neighbor will
reinitialize the adjacency in order to guarantee that the SRMflags
have been set on its database, thus ensuring eventual LSPDB
synchronization. This is guaranteed to happen except in the case
where the Adjacency Three-Way State in the received IIH is "UP" and
the Neighbor Extended Local Circuit ID matches the extended local
circuit ID assigned by the restarting router. In this case the
restarting router MUST force the adjacency to reinitialize by setting
the local Adjacency Three-Way State to "DOWN" and sending a normal
IIH.
In the case of a LAN interface, receipt of an IIH not containing the
restart TLV is unremarkable since synchronization can still occur so
long as at least one of the non-restarting neighboring routers on the
LAN supports restart. Therefore T1 continues to run in this case.
If none of the neighbors on the LAN are restart capable, T1 will
eventually expire after the locally defined number of retries.
In the case of a Point-to-Point circuit, the "LocalCircuitID" and
"Extended Local Circuit ID" information contained in the IIH can be
used immediately to generate an IIH containing the correct 3-way
Shand & Ginsberg Informational [Page 9]
RFC 3847 Restart signaling for IS-IS July 2004
handshake information. The presence of "Neighbor Extended Local
Circuit ID" information which does not match the value currently in
use by the local system is ignored (since the IIH may have been
transmitted before the neighbor had received the new value from the
restarting router), but the adjacency remains in the initializing
state until the correct information is received.
In the case of a LAN circuit, the source neighbor information (e.g.,
SNPAAddress) is recorded and used for adjacency establishment and
maintenance as normal.
When BOTH a complete set of CSNP(s) (for each active level, in the
case of a point-to-point circuit) and an acknowledgement have been
received over the interface, the timer T1 is cancelled.
Once the timer T1 has been cancelled, subsequent IIHs are transmitted
according to the normal algorithms, but including the restart TLV
with both RR and RA clear.
If a LAN contains a mixture of systems, only some of which support
the new algorithm, database synchronization is still guaranteed, but
the "old" systems will have reinitialized their adjacencies.
If an interface is active, but does not have any neighboring router
reachable over that interface, the timer T1 would never be cancelled,
and according to clause 3.4.1.1, the SPF would never be run.
Therefore timer T1 is cancelled after some pre-determined number of
expirations (which MAY be 1).
3.3.2. Adjacency Acquisition During Start
The starting router wants to ensure that in the event that a
neighboring router has an adjacency to the starting router in the
"UP" state (from a previous incarnation of the starting router), this
adjacency is reinitialized. The starting router also wants
neighboring routers to suppress advertisement of an adjacency to the
starting router until LSP database synchronization is achieved. This
is achieved by sending IIHs with the RR bit clear and the SA bit set
in the restart TLV. The RR bit remains clear and the SA bit remains
set in subsequent transmissions of IIHs until the adjacency has
reached the "UP" state and the initial T1 timer interval (see below)
has expired.
Receipt of an IIH with the RR bit clear will result in the
neighboring router utilizing normal operation of the adjacency state
machine. This will ensure that any old adjacency on the neighboring
router will be reinitialized.
Shand & Ginsberg Informational [Page 10]
RFC 3847 Restart signaling for IS-IS July 2004
Upon receipt of an IIH with the SA bit set, the behavior described in
3.2.2 is followed.
Upon starting, a router starts timer T2 for each LSPDB.
For each interface (and in the case of a LAN circuit, for each
level), when an adjacency reaches the "UP" state, the starting router
starts a timer T1 and transmits an IIH containing the restart TLV
with the RR bit clear and SA bit set. Upon expiry of the timer T1,
it is restarted and the IIH is retransmitted with both RR and SA bits
set (only the RR bit has changed state from earlier IIHs).
Upon receipt of an IIH with the RR bit set (regardless of whether the
SA is set or not), the behavior described in 3.2.1 is followed.
When an IIH is received by the starting router and the IIH contains a
restart TLV with the RA bit set (and on LAN circuits with a Restart
Neighbor System ID which matches that of the local system), the
receipt of the acknowledgement over that interface is noted.
On a Point-to-Point link, receipt of an IIH not containing the
restart TLV is also treated as an acknowledgement, since it indicates
that the neighbor is not restart capable. Since the neighbor will
have reinitialized the adjacency, this guarantees that SRMflags have
been set on its database, thus ensuring eventual LSPDB
synchronization. However, since no CSNP is guaranteed to be received
over this interface, the timer T1 is cancelled immediately without
waiting for a complete set of CSNP(s). Synchronization may therefore
be deemed complete even though there are some LSPs which are held
(only) by this neighbor (see section 3.4).
In the case of a LAN interface, receipt of an IIH not containing the
restart TLV is unremarkable since synchronization can still occur so
long as at least one of the non-restarting neighboring routers on the
LAN supports restart. Therefore T1 continues to run in this case.
If none of the neighbors on the LAN are restart capable, T1 will
eventually expire after the locally defined number of retries. The
usual operation of the update process will ensure that
synchronization is eventually achieved.
When BOTH a complete set of CSNP(s) (for each active level, in the
case of a point-to-point circuit) and an acknowledgement have been
received over the interface, the timer T1 is cancelled. Subsequent
IIHs sent by the starting router have the RR and RA bits clear and
the SA bit set in the restart TLV.
Timer T1 is cancelled after some pre-determined number of expirations
(which MAY be 1).
Shand & Ginsberg Informational [Page 11]
RFC 3847 Restart signaling for IS-IS July 2004
When the T2 timer(s) are cancelled or expire, transmission of
"normal" IIHs (with RR, RA, and SA bits clear) will begin.
3.3.3. Multiple Levels
A router which is operating as both a Level 1 and a Level 2 router on
a particular interface MUST perform the above operations for each
level.
On a LAN interface, it MUST send and receive both Level 1 and Level 2
IIHs and perform the CSNP synchronizations independently for each
level.
On a point-to-point interface, only a single IIH (indicating support
for both levels) is required, but it MUST perform the CSNP
synchronizations independently for each level.
3.4. Database Synchronization
When a router is started or restarted it can expect to receive a (set
of) CSNP(s) over each interface. The arrival of the CSNP(s) is now
guaranteed, since an IIH with the RR bit set will be retransmitted
until the CSNP(s) are correctly received.
The CSNPs describe the set of LSPs that are currently held by each
neighbor. Synchronization will be complete when all these LSPs have
been received.
When (re)starting, a router starts an instance of timer T2 for each
LSPDB as described in 3.3.1 or 3.3.2. In addition to normal
processing of the CSNPs, the set of LSPIDs contained in the first
complete set of CSNP(s) received over each interface is recorded,
together with their remaining lifetime. In the case of a LAN
interface, a complete set of CSNPs MUST consist of CSNPs received
from neighbor(s) which are not restarting. If there are multiple
interfaces on the (re)starting router, the recorded set of LSPIDs is
the union of those received over each interface. LSPs with a
remaining lifetime of zero are NOT so recorded.
As LSPs are received (by the normal operation of the update process)
over any interface, the corresponding LSPID entry is removed (it is
also removed if an LSP arrives before the CSNP containing the
reference). When an LSPID has been held in the list for its
indicated remaining lifetime, it is removed from the list. When the
list of LSPIDs is empty and the timer T1 has been cancelled for all
the interfaces that have an adjacency at this level, the timer T2 is
cancelled.
Shand & Ginsberg Informational [Page 12]
RFC 3847 Restart signaling for IS-IS July 2004
At this point, the local database is guaranteed to contain all the
LSP(s) (either the same sequence number, or a more recent sequence
number) that were present in the neighbors' databases at the time of
(re)starting. LSPs that arrived in a neighbor's database after the
time of (re)starting may or may not be present, but the normal
operation of the update process will guarantee that they will
eventually be received. At this point, the local database is deemed
to be "synchronized".
Since LSPs mentioned in the CSNP(s) with a zero remaining lifetime
are not recorded, and those with a short remaining lifetime are
deleted from the list when the lifetime expires, cancellation of the
timer T2 will not be prevented by waiting for an LSP that will never
arrive.
3.4.1. LSP Generation and Flooding and SPF Computation
The operation of a router starting, as opposed to restarting, is
somewhat different. These two cases are dealt with separately below.
3.4.1.1. Restarting
In order to avoid causing unnecessary routing churn in other routers,
it is highly desirable that the router's own LSPs generated by the
restarting system are the same as those previously present in the
network (assuming no other changes have taken place). It is
important therefore not to regenerate and flood the LSPs until all
the adjacencies have been re-established and any information required
for propagation into the local LSPs is fully available. Ideally, the
information is loaded into the LSPs in a deterministic way, such that
the same information occurs in the same place in the same LSP (and
hence the LSPs are identical to their previous versions). If this
can be achieved, the new versions may not even cause SPF to be run in
other systems. However, provided the same information is included in
the set of LSPs (albeit in a different order, and possibly different
LSPs), the result of running the SPF will be the same and will not
cause churn to the forwarding tables.
In the case of a restarting router, none of the router's own LSPs are
transmitted, nor are the router's own forwarding tables updated while
the timer T3 is running.
Redistribution of inter-level information MUST be regenerated before
this router's LSP is flooded to other nodes. Therefore, the Level-n
non-pseudonode LSP(s) MUST NOT be flooded until the other level's T2
timer has expired and its SPF has been run. This ensures that any
inter-level information which is to be propagated can be included in
the Level-n LSP(s).
Shand & Ginsberg Informational [Page 13]
RFC 3847 Restart signaling for IS-IS July 2004
During this period, if one of the router's own (including
pseudonodes) LSPs is received, which the local router does not
currently have in its own database, it is NOT purged. Under normal
operation, such an LSP would be purged, since the LSP clearly should
not be present in the global LSP database. However, in the present
circumstances, this would be highly undesirable, because it could
cause premature removal of a router's own LSP - and hence churn in
remote routers. Even if the local system has one or more of the
router's own LSPs (which it has generated, but not yet transmitted),
it is still not valid to compare the received LSP against this set,
since it may be that as a result of propagation between Level 1 and
Level 2 (or vice versa), a further router's own LSP will need to be
generated when the LSP databases have synchronized.
During this period a restarting router SHOULD send CSNPs as it
normally would. Information about the router's own LSPs MAY be
included, but if it is included it MUST be based on LSPs which have
been received, not on versions which have been generated (but not yet
transmitted). This restriction is necessary to prevent premature
removal of an LSP from the global LSP database.
When the timer T2 expires or is cancelled indicating that
synchronization for that level is complete, the SPF for that level is
run in order to derive any information which is required to be
propagated to another level, but the forwarding tables are not yet
updated.
Once the other level's SPF has run and any inter-level propagation
has been resolved, the router's own LSPs can be generated and
flooded. Any own LSPs which were previously ignored, but which are
not part of the current set of own LSPs (including pseudonodes) MUST
then be purged. Note that it is possible that a Designated Router
change may have taken place, and consequently the router SHOULD purge
those pseudonode LSPs which it previously owned, but which are now no
longer part of its set of pseudonode LSPs.
When all the T2 timers have expired or been cancelled, the timer T3
is cancelled and the local forwarding tables are updated.
If the timer T3 expires before all the T2 timers have expired or been
cancelled, this indicates that the synchronization process is taking
longer than the minimum holding time of the neighbors. The router's
own LSP(s) for levels which have not yet completed their first SPF
computation are then flooded with the overload bit set to indicate
that the router's LSPDB is not yet synchronized (and therefore other
routers MUST NOT compute routes through this router). Normal
operation of the update process resumes and the local forwarding
tables are updated. In order to prevent the neighbor's adjacencies
Shand & Ginsberg Informational [Page 14]
RFC 3847 Restart signaling for IS-IS July 2004
from expiring, IIHs with the normal interface value for the holding
time are transmitted over all interfaces with neither RR nor RA set
in the restart TLV. This will cause the neighbors to refresh their
adjacencies. The router's own LSP(s) will continue to have the
overload bit set until timer T2 has expired or been cancelled.
3.4.1.2. Starting
In the case of a starting router, as soon as each adjacency is
established, and before any CSNP exchanges, the router's own zeroth
LSP is transmitted with the overload bit set. This prevents other
routers from computing routes through the router until it has
reliably acquired the complete set of LSPs. The overload bit remains
set in subsequent transmissions of the zeroth LSP (such as will occur
if a previous copy of the router's own zeroth LSP is still present in
the network) while any timer T2 is running.
When all the T2 timers have been cancelled, the router's own LSP(s)
MAY be regenerated with the overload bit clear (assuming the router
is not in fact overloaded, and there is no other reason, such as
incomplete BGP convergence, to keep the overload bit set) and flooded
as normal.
Other LSPs owned by this router (including pseudonodes) are generated
and flooded as normal, irrespective of the timer T2. The SPF is also
run as normal and the RIB and FIB updated as routes become available.
To avoid the possible formation of temporary blackholes, the starting
router sets the SA bit in the restart TLV (as described in 3.3.2) in
all IIHs that it sends.
When all T2 timers have been cancelled, the starting router MUST
transmit IIHs with the SA bit clear.
4. State Tables
This section presents state tables which summarize the behaviors
described in this document. Other behaviors, in particular adjacency
state transitions and LSP database update operation, are NOT included
in the state tables except where this document modifies the behaviors
described in [2] and [4].
The states named in the columns of the tables below are a mixture of
states that are specific to a single adjacency (ADJ suppressed, ADJ
Seen RA, ADJ Seen CSNP) and states which are indicative of the state
of the protocol instance (Running, Restarting, Starting, SPF Wait).
Shand & Ginsberg Informational [Page 15]
RFC 3847 Restart signaling for IS-IS July 2004
Three state tables are presented from the point of view of a running
router, a restarting router, and a starting router.
4.1. Running Router
Event | Running | ADJ suppressed
==============================================================
RX RR | Maintain ADJ State |
| Send RA |
| Set SRM,send CSNP |
| (Note 1) |
| Update Hold Time, |
| set Restart Mode |
| (Note 2) |
-------------+----------------------+-------------------------
RX RR clr | Clr Restart mode |
-------------+----------------------+-------------------------
RX SA | Suppress IS neighbor |
| TLV in LSP(s) |
| Goto ADJ Suppressed |
-------------+----------------------+-------------------------
RX SA clr | |Unsuppress IS neighbor
| | TLV in LSP(s)
| |Goto Running
==============================================================
Note 1: CSNPs are sent by routers in accordance with Section 3.2.1c
Note 2: If Restart Mode clear
Shand & Ginsberg Informational [Page 16]
RFC 3847 Restart signaling for IS-IS July 2004
4.2. Restarting Router
Event | Restarting | ADJ Seen | ADJ Seen | SPF Wait
| | RA | CSNP |
===================================================================
Router | Send IIH/RR | | |
restarts | ADJ Init | | |
| Start T1,T2,T3 | | |
------------+--------------------+-----------+-----------+------------
RX RR | Send RA | | |
------------+--------------------+-----------+-----------+------------
RX RA | Adjust T3 | | Cancel T1 |
| Goto ADJ Seen RA | | Adjust T3 |
----------- +--------------------+-----------+-----------+------------
RX CSNP set| Goto ADJ Seen CSNP | Cancel T1 | |
------------+--------------------+-----------+-----------+------------
RX IIH w/o | Cancel T1 (Point- | | |
Restart TLV| to-point only) | | |
------------+--------------------+-----------+-----------+------------
T1 Expires | Send IIH/RR |Send IIH/RR|Send IIH/RR|
| Restart T1 | Restart T1| Restart T1|
------------+--------------------+-----------+-----------+------------
T1 Expires | Send IIH/ | Send IIH/ | Send IIH/ |
nth time | normal | normal | normal |
------------+--------------------+-----------+-----------+------------
T2 expires | Trigger SPF | | |
| Goto SPF Wait | | |
------------+--------------------+-----------+-----------+------------
T3 expires | Set OL | | |
| Flood local LSPs | | |
| Update fwd plane | | |
------------+--------------------+-----------+-----------+------------
LSP DB Sync| Cancel T2, and T3 | | |
| Trigger SPF | | |
| Goto SPF wait | | |
------------+--------------------+-----------+-----------+------------
All SPF | | | | Clear OL
done | | | | Update fwd
| | | | plane
| | | | Flood local
| | | | LSPs
| | | | Goto Running
======================================================================
Shand & Ginsberg Informational [Page 17]
RFC 3847 Restart signaling for IS-IS July 2004
4.3. Starting Router
Event | Starting | ADJ Seen RA| ADJ Seen CSNP
=============================================================
Router | Send IIH/SA | |
starts | Start T1,T2 | |
-------------+-------------------+------------+---------------
RX RR | Send RA | |
-------------+-------------------+------------+---------------
RX RA | Goto ADJ Seen RA | | Cancel T1
-------------+-------------------+------------+---------------
RX CSNP Set | Goto ADJ Seen CSNP| Cancel T1 |
-------------+-------------------+------------+---------------
RX IIH w | Cancel T1 | |
no Restart | (Point-to-Point | |
TLV | only) | |
-------------+-------------------+------------+---------------
ADJ UP | Start T1 | |
| Send local LSPs | |
| w OL | |
-------------+-------------------+------------+---------------
T1 Expires | Send IIH/RR |Send IIH/RR | Send IIH/RR
| and SA | and SA | and SA
| Restart T1 |Restart T1 | Restart T1
-------------+-------------------+------------+---------------
T1 Expires | Send IIH/SA |Send IIH/SA | Send IIH/SA
nth time | | |
-------------+-------------------+------------+---------------
T2 expires | Clear OL | |
| Send IIH normal | |
| Goto Running | |
-------------+-------------------+------------+---------------
LSP DB Sync | Cancel T2 | |
| Clear OL | |
| Send IIH normal | |
==============================================================
5. Security Considerations
Any new security issues raised by the procedures in this document
depend upon the ability of an attacker to inject a false but
apparently valid IIH, the ease/difficulty of which has not been
altered.
Shand & Ginsberg Informational [Page 18]
RFC 3847 Restart signaling for IS-IS July 2004
If the RR bit is set in a false IIH, neighbors who receive such an
IIH will continue to maintain an existing adjacency in the "UP" state
and may (re)send a complete set of CSNPs. While the latter action is
wasteful, neither action causes any disruption in correct protocol
operation.
If the RA bit is set in a false IIH, a (re)starting router which
receives such an IIH may falsely believe that there is a neighbor on
the corresponding interface which supports the procedures described
in this document. In the absence of receipt of a complete set of
CSNPs on that interface, this could delay the completion of (re)start
procedures by requiring the timer T1 to time out the locally defined
maximum number of retries. This behavior is the same as would occur
on a LAN where none of the (re)starting router's neighbors support
the procedures in this document and is covered in Sections 3.3.1 and
3.3.2.
If an SA bit is set in a false IIH, this could cause suppression of
the advertisement of an IS neighbor which could either continue for
an indefinite period, or occur intermittently with the result being a
possible loss of reachability to some destinations in the network
and/or increased frequency of LSP flooding and SPF calculation.
The possibility of IS-IS PDU spoofing can be reduced by the use of
authentication as described in [1] and [2], and especially the use of
cryptographic authentication as described in [5].
6. IANA Considerations
This document defines the following IS-IS TLV that is listed in the
IS-IS TLV code-point registry:
Type Description IIH LSP SNP
---- ----------------------------------- --- --- ---
211 Restart TLV y n n
7. Normative References
[1] Callon, R., "OSI IS-IS for IP and Dual Environment", RFC 1195,
December 1990.
[2] ISO, "Intermediate system to Intermediate system routeing
information exchange protocol for use in conjunction with the
Protocol for providing the Connectionless-mode Network Service
(ISO 8473)," ISO/IEC 10589:2002, Second Edition.
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
Shand & Ginsberg Informational [Page 19]
RFC 3847 Restart signaling for IS-IS July 2004
[4] Katz, D. and R. Saluja, "Three-Way Handshake for IS-IS Point-
to-Point Adjacencies", RFC 3373, September 2002.
[5] Li, T. and R. Atkinson, "Intermediate System to Intermediate
System (IS-IS) Cryptographic Authentication", RFC 3567, July
2003.
8. Acknowledgements
The authors would like to acknowledge contributions made by Jeff
Parker, Radia Perlman, Mark Schaefer, Naiming Shen, Nischal Sheth,
Russ White, and Rena Yang.
9. Authors' Addresses
Mike Shand
Cisco Systems
250 Longwater Avenue,
Reading,
Berkshire,
RG2 6GB
UK
Phone: +44 208 824 8690
EMail:
[email protected]
Les Ginsberg
Cisco Systems
510 McCarthy Blvd.
Milpitas, Ca. 95035 USA
EMail:
[email protected]
Shand & Ginsberg Informational [Page 20]
RFC 3847 Restart signaling for IS-IS July 2004
10. Full Copyright Statement
Copyright (C) The Internet Society (2004). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at ietf-
[email protected].
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Shand & Ginsberg Informational [Page 21]
