Network Working Group W. Simpson

Network Working Group W. Simpson
Request for Comments: 1333 Daydreamer
May 1992

PPP Link Quality Monitoring

Status of this Memo

This RFC specifies an IAB standards track protocol for the Internet
community, and requests discussion and suggestions for improvements.
Please refer to the current edition of the "IAB Official Protocol
Standards" for the standardization state and status of this protocol.
Distribution of this memo is unlimited.

Abstract

The Point-to-Point Protocol (PPP) [1] provides a standard method of
encapsulating Network Layer protocol information over point-to-point
links. PPP also defines an extensible Link Control Protocol, which
allows negotiation of a Quality Protocol for continuous monitoring of
the viability of the link.

This document defines a protocol for generating Link-Quality-Reports.

This RFC is a product of the Point-to-Point Protocol Working Group of
the Internet Engineering Task Force (IETF). Comments on this memo
should be submitted to the [email protected] mailing list.

Simpson [Page i]

RFC 1333 PPP Link Quality Monitoring May 1992

Table of Contents

1. Introduction .......................................... 1

2. Link Quality Monitoring ............................... 2
2.1 Design Motivation ............................... 2
2.2 Counters ........................................ 2
2.3 Counting Packets and Octets ..................... 4
2.4 Processes ....................................... 4
2.5 Configuration Option Format ..................... 6
2.6 Packet Format ................................... 8
2.7 Transmission of Reports ......................... 12
2.8 Calculations .................................... 12
2.9 Failure Detection ............................... 13
2.10 Policy Suggestions .............................. 14

SECURITY CONSIDERATIONS ...................................... 14

REFERENCES ................................................... 14

ACKNOWLEDGEMENTS ............................................. 14

CHAIR'S ADDRESS .............................................. 15

AUTHOR'S ADDRESS ............................................. 15

Simpson [Page ii]

RFC 1333 PPP Link Quality Monitoring May 1992

1. Introduction

PPP has three main components:

1. A method for encapsulating datagrams over serial links.

2. A Link Control Protocol (LCP) for establishing, configuring,
and testing the data-link connection.

3. A family of Network Control Protocols (NCPs) for establishing
and configuring different network-layer protocols.

In order to establish communications over a point-to-point link, each
end of the PPP link must first send LCP packets to configure the data
link during the Establishment phase. During the Authentication and
Network-Layer Protocol phases, the link may be tested to determine if
quality is sufficient for operation. This testing is completely
optional.

If an implementation desires that the peer use some specific link
quality monitoring protocol, then it MUST negotiate the use of that
protocol using the Quality-Protocol Configuration Option during Link
Establishment phase.

The negotiation mechanism is independent in each direction. However,
if the peer agrees to send Quality-Protocol packets, it MUST
correctly process such packets on reception, even if it does not
request such packets or implement a monitoring policy.

Simpson [Page 1]

RFC 1333 PPP Link Quality Monitoring May 1992

2. Link Quality Monitoring

Data communications links are rarely perfect. Packets can be dropped
or corrupted for various reasons (line noise, equipment failure,
buffer overruns, etc.). Sometimes, it is desirable to determine
when, and how often, the link is dropping data. Routers, for
example, may want to temporarily allow another route to take
precedence. An implementation may also have the option of
disconnecting and switching to an alternate link. The process of
determining data loss is called "Link Quality Monitoring".

2.1. Design Motivation

There are many different ways to measure link quality, and even more
ways to react to it. Rather than specifying a single scheme, Link
Quality Monitoring is divided into a "mechanism" and a "policy". PPP
fully specifies the "mechanism" for Link Quality Monitoring by
defining the Link-Quality-Report (LQR) packet and specifying a
procedure for its use. PPP does NOT specify a Link Quality
Monitoring "policy" -- how to judge link quality or what to do when
it is inadequate. That is left as an implementation decision, and
can be different at each end of the link. Implementations are
allowed, and even encouraged, to experiment with various link quality
policies. The Link Quality Monitoring mechanism specification
insures that two implementations with different policies may
communicate and interoperate.

To allow flexible policies to be implemented, the PPP Link Quality
Monitoring mechanism measures data loss in units of packets, octets,
and Link-Quality-Reports. Each measurement is made separately for
each half of the link, both inbound and outbound. All measurements
are communicated to both ends of the link so that each end of the
link can implement its own link quality policy for both its outbound
and inbound links.

Finally, the Link Quality Monitoring protocol is designed to be
implementable on many different kinds of systems. Although it may be
common to implement PPP (and especially Link Quality Monitoring) as a
single software process, multi-process implementations with hardware
support are also envisioned. The PPP Link Quality Monitoring
mechanism provides for this by careful definition of the Link-
Quality-Report packet format, and by specifying reference points for
all data transmission and reception measurements.

2.2. Counters

Each Link Quality Monitoring implementation maintains counts of the
number of packets and octets transmitted and successfully received,

Simpson [Page 2]

RFC 1333 PPP Link Quality Monitoring May 1992

and periodically transmits this information to its peer in a Link-
Quality-Report packet.

These counters are similar to sequence numbers; they are constantly
increasing to give a "relative" indication of the number of packets
and octets communicated across the outbound link. By comparing the
values in successive Link-Quality-Reports, an LQR receiver can
compute the "delta" number of packets and octets successfully
communicated across the link. Comparing these absolute numbers then
gives an indication of a link's quality. Relative numbers, rather
than absolute, are transmitted because they greatly simplify link
synchronization.

The Link-Quality-Report uses the Interface counters defined by SNMP
MIB-II [2]. These counters are not initialized to any particular
value when the LCP enters the Establishment phase.

In addition, the Link-Quality-Report requires the implementation of
the following three unsigned, monotonically increasing counters which
conform to the type and size requirements for SNMP MIB Counters [3].

OutLQRs

OutLQRs is a 32-bit counter which increases by one for each
tranmitted Link-Quality-Report packet. This counter MUST be set
to zero when the LCP enters the Establishment phase, and MUST NOT
be reset until the LCP leaves the Termination phase. This counter
is incremented before it is inserted into the LQR packet.

InLQRs

InLQRs is a 32-bit counter which increases by one for each
received Link-Quality-Report packet. This counter MUST be set to
zero when the LCP enters the Establishment phase, and MUST NOT be
reset until the LCP leaves the Termination phase. This counter is
incremented before it is inserted (in an implementation dependent
fashion) into the LQR packet.

InGoodOctets

InGoodOctets is a 32-bit counter which increases by the number of
octets in each successfully received Data Link Layer packet.
Unlike the MIB ifInOctets, octets for frames which are counted in
ifInDiscards and ifInErrors MUST NOT be counted. This counter MAY
be set to any initial value when the LCP enters the Establishment
phase, but MUST NOT be reset until the LCP leaves the Termination
phase.

Simpson [Page 3]

RFC 1333 PPP Link Quality Monitoring May 1992

2.3. Counting Packets and Octets

The intent of the counters is to provide an indication of the amount
of information passing over the link, rather than an actual
measurement of the total bandwidth used. This specification is
designed to yield the same count in various circumstances, such as
when a separate device provides the framing and escaping mechanisms
invisibly to the implementation, or a synchronous-to-asynchronous
converter in the link changes between mechanisms.

All octets which are included in the FCS calculation MUST be counted,
including the packet header, the information field, and any padding.
The FCS octets MUST also be counted, and one flag octet per frame
MUST be counted. All other octets (such as additional flag
sequences, and escape bits or octets) MUST NOT be counted.

When inserting the packet and octet counts in the LQR, the counts
MUST include the expected values for the LQR itself.

2.4. Processes

The PPP Link Quality Monitoring mechanism is described using a
"logical process" model. As shown below, there are five logical
processes duplicated at each end of the duplex link.

+---------+ +-------+ +----+ Outbound
| |-->| Mux |-->| Tx |=========>
| Link- | +-------+ +----+
| Manager |
| | +-------+ +----+ Inbound
| |<--| Demux |<--| Rx |<=========
+---------+ +-------+ +----+

Link-Manager

The Link-Manager process transmits and receives Link-Quality-
Reports, and implements the desired link quality policy. LQR
packets are transmitted at a constant rate, which is negotiated by
the LCP Quality-Protocol Configuration Option.

Mux

The Mux process multiplexes packets from the various protocols
(e.g., LCP, IP, XNS, etc.) into a single, sequential, and
prioritized stream of packets. Link-Quality-Report packets MUST
be given the highest possible priority to insure that link quality
information is communicated in a timely manner.

Simpson [Page 4]

RFC 1333 PPP Link Quality Monitoring May 1992

Tx

The Tx process maintains the MIB counters ifOutUniPackets and
ifOutOctets, and the internal counter OutLQRs, which are used to
measure the amount of data which is transmitted on the outbound
link. When Tx processes a Link-Quality-Report packet, it inserts
the values of these counters into the corresponding PeerOut...
fields of the packet. The Tx process MUST follow the Mux process
so that packets are counted in the order transmitted to the link.

Rx

The Rx process maintains the MIB counters ifInUniPackets,
ifInDiscards, ifInErrors and IfInOctets, and the internal counters
InLQRs and InGoodOctets, which are used to measure the amount of
data which is received by the inbound link. When Rx processes a
Link-Quality-Report packet, it inserts the values of these
counters into the corresponding SaveIn... fields of the packet (in
an implementation dependent manner).

Demux

The Demux process demultiplexes packets for the various protocols.
The Demux process MUST follow the Rx process so that packets are
counted in the order received from the link.

Simpson [Page 5]

RFC 1333 PPP Link Quality Monitoring May 1992

2.5. Configuration Option Format

Description

Implementations MUST be prepared to receive the Quality-Protocol
Configuration Option for the Link-Quality-Report. However,
negotiation is not required. Negotiation is only necessary when
the implementation wishes to ensure that the peer transmits Link-
Quality-Reports as opposed to some other Quality-Protocol, or else
to prevent the peer from maintaining its own timer, or else to
establish a maximum time between transmissions of Link-Quality-
Reports.

A summary of the Quality-Protocol Configuration Option format to
negotiate the Link-Quality-Report is shown below. The fields are
transmitted from left to right.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Quality-Protocol |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reporting-Period |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type

4

Length

8

Quality-Protocol

c025 (hex) for Link-Quality-Report

Reporting-Period

The Reporting-Period field is four octets and indicates the
maximum time in hundredths of seconds between transmission of
packets. The peer MAY transmit packets at a faster rate than that
which was negotiated.

A value of zero indicates that the peer does not need to maintain
a timer. Instead, the peer generates a LQR immediately upon
receiving a LQR. A value of zero MUST be Nak'd by the peer with

Simpson [Page 6]

RFC 1333 PPP Link Quality Monitoring May 1992

an appropriate non-zero value when that peer has sent or will send
a Configure-Request packet containing the Quality-Protocol
Configuration Option for the Link-Quality-Report with a zero
Reporting-Period.

Simpson [Page 7]

RFC 1333 PPP Link Quality Monitoring May 1992

2.6. Packet Format

Exactly one Link-Quality-Report packet is encapsulated in the
Information field of PPP Data Link Layer frames where the protocol
field indicates type hex c025 (Link-Quality-Report). A summary of
the LQR packet format is shown below. The names of the fields are
relative to the packet receiver, since it is the receiver who
requested the packet in the Configuration Option. The fields are
transmitted from left to right.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Magic-Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LastOutLQRs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LastOutPackets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LastOutOctets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerInLQRs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerInPackets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerInDiscards |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerInErrors |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerInOctets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerOutLQRs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerOutPackets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PeerOutOctets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

The following fields are not actually transmitted over the inbound
link. Rather, they are logically appended (in an implementation
dependent manner) to the packet by the implementation's Rx process.

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SaveInLQRs |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SaveInPackets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SaveInDiscards |

Simpson [Page 8]

RFC 1333 PPP Link Quality Monitoring May 1992

+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SaveInErrors |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SaveInOctets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Magic-Number

The Magic-Number field is four octets and aids in detecting links
which are in the looped-back condition. Unless modified by a
Configuration Option, the Magic-Number MUST be transmitted as zero
and MUST be ignored on reception. If Magic-Numbers have been
negotiated, incoming LQR packets SHOULD be checked to ensure that
the local end is not seeing its own Magic-Number and thus a
looped-back link. See the Magic-Number Configuration Option for
further explanation.

LastOutLQRs

The LastOutLQRs field is four octets, and is copied from the most
recently received PeerOutLQRs on transmission.

LastOutPackets

The LastOutPackets field is four octets, and is copied from the
most recently received PeerOutPackets on transmission.

LastOutOctets

The LastOutOctets field is four octets, and is copied from the
most recently received PeerOutOctets on transmission.

PeerInLQRs

The PeerInLQRs field is four octets, and is copied from the most
recently received SaveInLQRs on transmission.

Whenever the PeerInLQRs field is discovered to be zero, the
LastOut... fields are indeterminate, and the PeerIn... fields
contain the initial values for the peer.

PeerInPackets

The PeerInPackets field is four octets, and is copied from the
most recently received SaveInPackets on transmission.

Simpson [Page 9]

RFC 1333 PPP Link Quality Monitoring May 1992

PeerInDiscards

The PeerInDiscards field is four octets, and is copied from the
most recently received SaveInDiscards on transmission.

PeerInErrors

The PeerInErrors field is four octets, and is copied from the most
recently received SaveInErrors on transmission.

PeerInOctets

The PeerInOctets field is four octets, and is copied from the most
recently received SaveInOctets on transmission.

PeerOutLQRs

The PeerOutLQRs field is four octets, and is copied from OutLQRs
on transmission. This number MUST include this LQR.

PeerOutPackets

The PeerOutPackets field is four octets, and is copied from the
current MIB ifOutUniPackets and ifOutNUniPackets on transmission.
This number MUST include this LQR.

PeerOutOctets

The PeerOutOctets field is four octets, and is copied from the
current MIB ifOutOctets on transmission. This number MUST include
this LQR.

SaveInLQRs

The SaveInLQRs field is four octets, and is copied from InLQRs on
reception. This number MUST include this LQR.

SaveInPackets

The SaveInPackets field is four octets, and is copied from the
current MIB ifInUniPackets and ifInNUniPackets on reception. This
number MUST include this LQR.

SaveInDiscards

The SaveInDiscards field is four octets, and is copied from the
current MIB ifInDiscards on reception. This number MUST include
this LQR.

Simpson [Page 10]

RFC 1333 PPP Link Quality Monitoring May 1992

SaveInErrors

The SaveInErrors field is four octets, and is copied from the
current MIB ifInErrors on reception. This number MUST include
this LQR.

SaveInOctets

The SaveInOctets field is four octets, and is copied from the
current InGoodOctets on reception. This number MUST include this
LQR.

Note that InGoodOctets is not the same as the MIB ifInOctets
counter, as InGoodOctets does not include octets for packets which
are discards or errors.

Simpson [Page 11]

RFC 1333 PPP Link Quality Monitoring May 1992

2.7. Transmission of Reports

When the PPP Link Control Protocol has reached the Opened state, the
Link Quality Monitoring process MAY commence sending Link-Quality-
Reports. If a Protocol-Reject is received specifying a LQR packet,
the LQM process MUST cease sending LQRs.

Usually, the LQR is transmitted when the LQR timer for the link
expires. If no LQR timer is used, a LQR is generated upon receipt of
an incoming LQR. The negotiation process ensures that at least one
side of the link is using a LQR timer.

In addition, a LQR is generated whenever two successive LQRs are
received which have the same PeerInLQRs value. This may indicate
that a LQR has been missed, or that the implementation is sending at
a significantly slower rate than the peer, or that the peer has
accelerated LQR generation to better quantify errors on the link.

Whenever a LQR is sent, the LQR timer MUST be restarted.

2.8. Calculations

Each time a Link-Quality-Report packet is received from the inbound
link, the Link-Manager can compare the associated fields. The fields
of the previous LQR can be subtracted from the current LQR values to
obtain an absolute "delta", which allows comparision of the changes
seen by each end of the link.

If the received PeerInLQRs field is zero, the LastOut... fields are
indeterminate, and the PeerIn... fields contain the initial values
for the peer. No calculations using these fields can be performed at
this time.

Implementation Note:

The following counters wrap to zero when their maximum value is
reached. Care must be taken to ensure that correct "delta"
calculations are performed at that time.

The LastOutLQRs field may be directly compared with the PeerInLQRs
field to determine how many outbound LQRs have been lost.

The LastOutLQRs field may be directly compared with the OutLQRs
counter to determine how many outbound LQRs are still in the
pipeline.

The change in PeerInPackets may be compared with the change in
LastOutPackets to determine the number of lost packets over the

Simpson [Page 12]

RFC 1333 PPP Link Quality Monitoring May 1992

outgoing link.

The change in PeerInOctets may be compared with the change in
LastOutOctets to determine the number of lost octets over the
outgoing link.

The change in SaveInPackets may be compared with the change in
PeerOutPackets to determine the number of lost packets over the
incoming link.

The change in SaveInOctets may be compared with the change in
PeerOutOctets to determine the number of lost octets over the
incoming link.

The change in the PeerInDiscards and PeerInErrors fields may be used
to determine whether packet loss is due to congestion in the peer
rather than physical link failure.

2.9. Failure Detection

When the link is operating well in both directions of the link, the
LQR is superfluous. The maximum time interval for transmitting LQRs
SHOULD be chosen to minimally interfere with active traffic.

When there is a measurable loss of data in either direction, if the
overall throughput is adequate, conditions are not severe enough to
warrant dropping the link. Sending LQRs faster will gain nothing,
except to measure peaks in the loss rate. The time interval MUST be
chosen to be long enough to have a good smoothing effect on the data,
while short enough to ensure fast enough response to complete
failure.

When the link is good incoming, but very bad outgoing, incoming LQRs
indicate a high loss on the outgoing side of the link. Sending LQRs
faster won't help, because they are probably lost on the way to the
peer.

When the link is good outgoing, but very bad incoming, incoming LRQs
will be frequently lost. In this case, LQRs SHOULD be sent at a
faster rate. This primarily relies on the peer to make an informed
policy decision. The peer will also send LQRs in response (due to
the duplicate PeerInLQRs field), and some of those LQRs may
successfully arrive.

When a LQR does not arrive within the time expected, or the LQR
received indicates that the links are truly bad, at least one
additional LQR SHOULD be sent. An algorithmic decision requires at
least 2 round trip intervals. The loss rate could be transient, due

Simpson [Page 13]

RFC 1333 PPP Link Quality Monitoring May 1992

to a heavily loaded link, or a lost outgoing LQR.

2.10. Policy Suggestions

Link-Quality-Report packets provide a mechanism to determine the link
quality, but it is up to each implementation to decide when the link
is usable. It is recommended that this policy implement some amount
of hysteresis so that the link does not bounce up and down. One
policy is to use a K out of N algorithm. In such an algorithm, there
must be K successes out of the last N periods for the link to be
considered of good quality.

Procedures for recovery from poor quality links are unspecified and
may vary from implementation to implementation. A suggested approach
is to immediately close all other Network-Layer protocols (i.e.,
cause IPCP to transmit a Terminate-Request), but to continue
transmitting Link-Quality-Reports. Once the link quality again
reaches an acceptable level, Network-Layer protocols can be
reconfigured.

Security Considerations

Security issues are not discussed in this memo.

References

[1] Simpson, W., "The Point-to-Point Protocol", RFC 1331, May 1992.

[2] McCloghrie, K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based internets: MIB-II", RFC
1213, March 1991.

[3] Rose, M., and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", RFC 1155,
May 1990.

Acknowledgments

Some of the text in this document is taken from RFC 1172, by Drew
Perkins of Carnegie Mellon University, and by Russ Hobby of the
University of California at Davis.

Special thanks to Craig Fox (Network Systems), and Karl Fox (Morning
Star Technologies), for design suggestions based on implementation
experience.

Simpson [Page 14]

RFC 1333 PPP Link Quality Monitoring May 1992

Chair's Address

The working group can be contacted via the current chair:

Brian Lloyd
Lloyd & Associates
3420 Sudbury Road
Cameron Park, California 95682

Phone: (916) 676-1147

EMail: [email protected]

Author's Address

Questions about this memo can also be directed to:

William Allen Simpson
Daydreamer
Computer Systems Consulting Services
P O Box 6205
East Lansing, MI 48826-6025

EMail: [email protected]

Simpson [Page 15]