; MXO-SD10.ASM -- SIERRA DATA SCIENCES overlay file for MEX10. 03/29/85
;
; You will want to look this file over carefully. There are a number of
; options that you can use to configure the program to suit your taste.
; This file adapts the SIERRA DATA SCIENCES SBC-100 computer to MDM7xx.
;
; Edit this file for your preferences then follow the "TO USE:" example
; shown below.
;
; Use the "SET" command to change the baudrate when desired. It starts
; out at 300 baud when the program is first called up.
;
; TO USE: First edit this file filling in answers for your own
; equipment. Then assemble with ASM.COM or equivalent
; assembler. Then use MLOAD to overlay the the results
; of this program to the original .COM file.
;
; = = = = = = = = = = = = = = = = = =
; 03/29/85 - Renamed MX0-SD10.ASM - Leon Suchard
; 03/29/85 - Modified to work with SDS SBC-100 - Leon Suchard
; 05/24/84 - MEXified overlay - Biff Bueffel
; 11/11/83 - Renamed to M7XE-1.ASM, no changes - Irv Hoff
; 07/27/83 - Renamed to work with MDM712 - Irv Hoff
; 07/01/83 - Revised to work with MDM711 - Irv Hoff
; 06/22/83 - Revised to work with MDM710 - Irv Hoff
; 05/27/83 - Updated to work with MDM709 - Irv Hoff
; 05/15/83 - Revised to work with MDM708 - Irv Hoff
; 04/11/83 - Updated to work with MDM707 - Irv Hoff
; 04/04/83 - Updated to work with MDM706 - Irv Hoff
; 03/03/83 - Modified MDM705KP for XEROX
; 820-II computers with external
; modems - David Wurz
;
; = = = = = = = = = = = = = = = = = =
;
BELL: EQU 07H ;bell
CR: EQU 0DH ;carriage return
ESC: EQU 1BH ;escape
LF: EQU 0AH ;linefeed
;
YES: EQU 0FFH
NO: EQU 0
;
; MEX service processor stuff
;
MEX EQU 0D00H ;address of the service processor
INMDM EQU 255 ;get char from port to A, CY=no more in 100 ms
TIMER EQU 254 ;delay 100ms * reg B
TMDINP EQU 253 ;B=# secs to wait for char, cy=no char
CHEKCC EQU 252 ;check for ^C from KBD, Z=present
SNDRDY EQU 251 ;test for modem-send ready
RCVRDY EQU 250 ;test for modem-receive ready
SNDCHR EQU 249 ;send a character to the modem (after sndrdy)
RCVCHR EQU 248 ;recv a char from modem (after rcvrdy)
LOOKUP EQU 247 ;table search: see CMDTBL comments for info
PARSFN EQU 246 ;parse filename from input stream
BDPARS EQU 245 ;parse baud-rate from input stream
SBLANK EQU 244 ;scan input stream to next non-blank
EVALA EQU 243 ;evaluate numeric from input stream
LKAHED EQU 242 ;get nxt char w/o removing from input
GNC EQU 241 ;get char from input, cy=1 if none
ILP EQU 240 ;inline print
DECOUT EQU 239 ;decimal output
PRBAUD EQU 238 ;print baud rate
;
PRINT EQU 9 ;MEX/BDOS print-string function call
;
;CHANGE PORT ASSIGNMENT TO CORRESPOND TO YOUR MODEM PORT - I USE
;SERIAL PORT B. --- L.S.
;
PORT: EQU 082H ;SIERRA DATA SCIENCES port B
MODCTL1: EQU PORT+1 ;Modem control port
MODDATP: EQU PORT ;Modem data port
MODCTL2: EQU PORT+1 ;Modem status port
MODRCVB: EQU 01H ;Your bit to test for receive
MODRCVR: EQU 01H ;Your value when receive ready
MODSNDB: EQU 04H ;Your bit to test for send
MODSNDR: EQU 04H ;Your value when send ready
;
;
ORG 100H
;
;
; Change the clock speed to suit your system
;
DS 3 ;(for "JMP START" instruction)
;
PMMIMODEM: DB NO ;yes=PMMI S-100 Modem 103H
SMARTMODEM: DB YES ;yes=HAYES Smartmodem, no=non-PMMI 104H
TOUCHPULSE: DB 'T' ;T=touch, P=pulse (Smartmodem-only) 105H
CLOCK: DB 40 ;clock speed in MHz x10, 25.5 MHz max. 106H
;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc.
MSPEED: DB 5 ;0=110 1=300 2=450 3=600 4=710 5=1200 107H
;6=2400 7=4800 8=9600 9=19200 default
BYTDLY: DB 5 ;0=0 delay 1=10ms 5=50 ms - 9=90 ms 108H
;default time to send character in ter-
;minal mode file transfer for slow BBS.
CRDLY: DB 5 ;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H
;default time for extra wait after CRLF
;in terminal mode file transfer
NOOFCOL: DB 5 ;number of DIR columns shown 10AH
SETUPTST: DB YES ;yes=user-added Setup routine 10BH
SCRNTEST: DB NO ;Cursor control routine 10CH
ACKNAK: DB YES ;yes=resend a record after any non-ACK 10DH
;no=resend a record after a valid NAK
BAKUPBYTE: DB YES ;yes=change any file same name to .BAK 10EH
CRCDFLT: DB YES ;yes=default to CRC checking 10FH
TOGGLECRC: DB YES ;yes=allow toggling of CRC to Checksum 110H
CONVBKSP: DB NO ;yes=convert backspace to rub 111H
TOGGLEBK: DB YES ;yes=allow toggling of bksp to rub 112H
ADDLF: DB NO ;no=no LF after CR to send file in 113H
;terminal mode (added by remote echo)
TOGGLELF: DB YES ;yes=allow toggling of LF after CR 114H
TRANLOGON: DB NO ;yes=allow transmission of logon 115H
;write logon sequence at location LOGON
SAVCCP: DB YES ;yes=do not overwrite CCP 116H
LOCONEXTCHR: DB NO ;yes=local command if EXTCHR precedes 117H
;no=external command if EXTCHR precedes
TOGGLELOC: DB YES ;yes=allow toggling of LOCONEXTCHR 118H
LSTTST: DB NO ;yes=printer available on printer port 119H
XOFFTST: DB NO ;yes=check for XOFF from remote while 11AH
;sending a file in terminal mode
XONWAIT: DB NO ;yes=wait for XON after CR while 11BH
;sending a file in terminal mode
TOGXOFF: DB YES ;yes=allow toggling of XOFF checking 11CH
IGNORCTL: DB YES ;yes=CTL-chars above ^M not displayed 11DH
EXTRA1: DB 0 ;for future expansion 11EH
EXTRA2: DB 0 ;for future expansion 11FH
BRKCHR: DB '@'-40H ;^@ = Send a 300 ms. break tone 120H
20H
NOCONNCT: DB 'N'-40H ;^N = Disconnect from the phone line 121H
LOGCHR: DB 'L'-40H ;^L = Send logon 122H
LSTCHR: DB 'P'-40H ;^P = Toggle printer 123H
UNSAVE: DB 'R'-40H ;^R = Close input text buffer 124H
TRANCHR: DB 'T'-40H ;^T = Transmit file to remote 125H
SAVECHR: DB 'Y'-40H ;^Y = Open input text buffer 126H
EXTCHR: DB '^'-40H ;^^ = Send next character 127H
;
;
DS 2 ; 128H
IN$MODCTL1: MVI A,10H ;channel 0, reset interrupts 12AH
OUT MODCTL1
IN MODCTL1 ;get the status bits
RET
DS 3
;
OUT$MODDATP: OUT MODDATP ! RET ;out modem data port 134H
DS 7
IN$MODDATP: IN MODDATP ! RET ;in modem data port 13EH
DS 7
ANI$MODRCVB: ANI MODRCVB ! RET ;bit to test for receive ready 148H
CPI$MODRCVR: CPI MODRCVR ! RET ;value of receive bit when rdy 14BH
ANI$MODSNDB: ANI MODSNDB ! RET ;bit to test for send ready 14EH
CPI$MODSNDR: CPI MODSNDR ! RET ;value of send bit when ready 151H
DS 6 ; 154H
OUT$MODCTL1: OUT MODCTL1 ! RET ;out modem control port 15AH
OUT$MODCTL2: OUT MODCTL2 ! RET ;out modem status port 15DH
;
;
DS 2 ;Not used by MEX 160H
DS 6 ; 162H
JMP$GOODBYE: JMP GOODBYE ; 168H
JMP$INITMOD: JMP INITMOD ;go to user written routine 16BH
JMP$NEWBAUD JMP NEWBAUD ;Change baudrate 16EH
RET ! NOP ! NOP ;(by-passes PMMI routine) 171H
RET ! NOP ! NOP ;(by-passes PMMI routine) 174H
JMP$SETUPR: JMP SETUPR ; 177H
DS 3 ; 17AH
JMP$SYSVER: JMP SYSVER ; 17DH
JMP$BREAK: JMP SENDBRK ; 180H
;
;
; Do not change the following six lines.
;
JMP$ILPRT: DS 3 ; 183H
JMP$INBUF DS 3 ; 186H
JMP$INLNCOMP: DS 3 ; 189H
JMP$INMODEM DS 3 ; 18CH
JMP$NXTSCRN: DS 3 ; 18FH
JMP$TIMER: DS 3 ; 192H
;
;
; Clear sequences -- CLREOS is clear to end of screen, CLRSCRN is clear
; entire screen.
;
CLREOS: LXI D,EOSMSG
MVI C,PRINT
CALL MEX
RET
;
CLRSCRN: LXI D,CLSMSG
MVI C,PRINT
CALL MEX
RET
;
;
SYSVER: MVI C,ILP ; 1A7H
CALL MEX
DB 'Version for SIERRA DATA SCIENCES SBC-100'
DB CR,LF,0
RET
;
;
; This routine allows a 300 ms. break tone to be sent to reset some
; time-shar computers.
;
SENDBRK: MVI A,5
OUT MODCTL1
MVI A,0F8H ;SEND A BREAK TONE
JMP GOODBYE1
;.....
;
;
; This routine sends a 300 ms. break tone and sets DTR low for the same
; length of time to disconnect some modems such as the Bell 212A, etc.
;
GOODBYE: MVI A,5
OUT MODCTL1 ;SEND TO THE STATUS PORT
MVI A,68H ;TURN OFF DTR
;
GOODBYE1: OUT MODCTL1
MVI B,3 ;WAIT FOR 300 MS.
MVI C,TIMER
CALL MEX
MVI A,5
OUT MODCTL1
MVI A,0E8H ;RESTORE TO NORMAL, 8 BITS, DTR ON, ETC.
OUT MODCTL1
RET
;.....
;
;
; SDS - Z80SIO initialization -- sets CTC timer 00H for send and receive
; baudrate.
;
INITMOD: MVI A,0 ;SELECT REGISTER
OUT MODCTL1
MVI A,18H ;THROW OUT OF MODE
OUT MODCTL1
MVI A,14H ;SELECT REGISTER
OUT MODCTL1
MVI A,044H ;SET ASCII PARAMETERS
OUT MODCTL1
MVI A,03H ;SELECT REG.
OUT MODCTL1
MVI A,0C1H ;ENABLE RECEIVE
OUT MODCTL1
MVI A,05H ;SELECT REG.
OUT MODCTL1
MVI A,0EAH ;ENABLE SEND, 'DTR', 'RTS'
OUT MODCTL1
;
INITMOD1: MVI A,1 ;DEFAULT TRANSFER TIME TO 300 BAUD
STA MSPEED
MVI A,047H ;DEFAULT TO 300 BAUD
OUT 00H ;SEND TO 'CTC' TIMER
;
INITMOD2: MVI A,05H ;INITIALIZE TO 300 BAUD
OUT 00H
RET
;.....
;
;
; Setup routine to allow changing modem speed with the SET command.
;
;
SETUPR: MVI C,SBLANK ;Any arguments?
CALL MEX
JC TELL ;If not, go display baud
LXI D,CMDTBL
MVI C,LOOKUP
CALL MEX ;Parse argument
PUSH H ;Save any parsed argument addrs on stack
RNC ;If we have one, return to it
POP H ;Oops, input not found in table
MVI C,ILP
CALL MEX ;Tell user input not valid
DB CR,LF,'Only 300 or 1200 allowed on SET command',CR,LF,0
RET
;
CMDTBL: DB '30','0'+80H
DW OK300
DB '120','0'+80H
DW OK1200
DB 0
;
TELL: MVI C,ILP
CALL MEX ;Print current baud rate
DB CR,LF,'Baud rate is now: ',0
LDA MSPEED
MVI C,PRBAUD
CALL MEX
RET
;
;
OK300: MVI A,1
LHLD BD300
JMP LOADBD
;
OK600: MVI A,3
LHLD BD600
JMP LOADBD
;
OK1200: MVI A,5
LHLD BD1200
JMP LOADBD
;
OK9600: MVI A,8
LHLD BD9600
;
LOADBD: STA INITMOD1+1 ;CHANGE TIME-TO-SEND TO MATCH BAUDRATE
MOV A,L ;GET BAUDRATE BYTE
STA INITMOD2+1 ;SEND TO 'CTC' TIMER FOR NEW BAUDRATE
JMP INITMOD1 ;REINITIALIZE TO NEW BAUDRATE, THEN DONE
;
;
NEWBAUD: CPI 1
JZ OK300
CPI 5
JZ OK1200
RET
;
;
; TABLE OF BAUDRATE PARAMETERS
;
BD300: DW 0005H
BD600: DW 0006H
BD1200: DW 0007H
BD9600: DW 000EH
;
BAUDBUF: DB 10,0
DS 10
;
EOSMSG: DB 0,0,0,0,'$'
CLSMSG: DB 0,0,0,0,'$'
;
; NOTE: MUST TERMINATE PRIOR TO 0B00H (with Smartmodem)
; 0D00H (without Smartmodem)
;
END
;
