; B5PH-1.INS - BYE5 insert for Philips "Happy Man" P2000C - 07/17/85
;
; Zilog Z80-SIO and 8430 CTC timer
;
; Note: This is an insert, not an overlay.
;
;
; = = = = = = = = = = = = = = = = = =
;
; 07/17/85 Written for use with BYE5 - Irv Hoff
;
; = = = = = = = = = = = = = = = = = =
;
;
PORT EQU 28H ; Data port
MDCTL1 EQU PORT+1 ; Modem control port
BRPORT EQU 21H ; Baud rate generator port (CTC)
;
MDRCV EQU 1 ; Modem receive ready bit
MDSND EQU 4 ; Modem send ready bit
MDDCD EQU 8 ; Data carrier detect
;
;
; First byte of CTC Command:
;
BDCMD1 EQU 47H ; Counter mode
;
BD300 EQU 128 ; 300 baud
BD1200 EQU 32 ; 1200 bps
BD2400 EQU 16 ; 2400 bps
;
;
;-----------------------------------------------------------------------
;
; See if we still have a carrier - if not, return with the zero flag set
;
MDCARCK:MVI A,10H ; Reset status
OUT MDCTL1
IN MDCTL1 ; Get status
ANI MDDCD ; Check for carrier
RET
;.....
;
;
; Disconnect and wait for an incoming call
;
MDINIT: MVI A,0 ; Setup to write register 0
OUT MDCTL1
MVI A,18H ; Reset channel
OUT MDCTL1
MVI A,4 ; Setup to write register 4
OUT MDCTL1
MVI A,44H ; Set 16x, 1 stop bit, no parity
OUT MDCTL1
MVI A,3 ; Setup to write register 3
OUT MDCTL1
MVI A,0C1H ; 8 bits, Rx enable
OUT MDCTL1
MVI A,5 ; Setup to write register 5
OUT MDCTL1
MVI A,68H ; DTR off
OUT MDCTL1
PUSH B ; Save in case it's being used elsewhere
MVI B,20 ; 2 second delay to drop any carrier
;
OFFTI: CALL DELAY ; 1 second delay
DCR B
JNZ OFFTI ; Keep looping until finished
POP B ; Restore 'BC'
MVI A,5 ; Setup to write register 5
OUT MDCTL1
MVI A,0E8H ; Turn DTR back on
OUT MDCTL1
;
IF IMODEM ; If using an intellegent modem
CALL IMINIT ; Go initialize it now
ENDIF ; IMODEM
;
RET
;.....
;
;
; Input a character from the modem port
;
MDINP: IN PORT ; Get character
RET
;.....
;
;
; Check the status to see if a character is available. I fyes, return
; with the zero flag set. If yes, use 0FFH to clear the flag.
;
MDINST: IN MDCTL1 ; Get status
ANI MDRCV ; Got a character
RZ ; Return if none
ORI 0FFH ; Otherwise set the proper flag
RET
;.....
;
;
; Send a character to the modem
;
MDOUTP: OUT PORT ; Send it
RET
;.....
;
;
; See if the output is ready for another character
;
MDOUTST:IN MDCTL1 ; Get status
ANI MDSND ; Ready for a character?
RET
;.....
;
;
; Reinitialize the modem and hang up the phone by dropping DTR and
; leaving it inactive.
;
MDQUIT: IF IMODEM
CALL IMQUIT
ENDIF ; IMODEM
;
;
; Called by the main program after caller types BYE
;
MDSTOP: MVI A,5 ; Setup to write register 5
OUT MDCTL1
MVI A,68H ; Turn off DTR until next time
OUT MDCTL1
RET
;.....
;
;
; The following routine sets the baudrate. BYE5 asks for the maximum
; speed you have available.
;
SETINV: ORI 0FFH ; Make sure zero flag is not set
RET
;.....
;
;
SET300: MVI B,BD300 ; Set for 300 baud
JMP SETBAUD
;
SET1200:MVI B,BD1200 ; Set for 1200 bps
JMP SETBAUD
;
SET2400:MVI B,BD2400 ; Set for 2400 bps
PUSH PSW
;
SETBAUD:MVI A,BDCMD1 ; Get CTC command word
OUT BRPORT ; Send first byte of command
MOV A,B ; Restore the baudrate
OUT BRPORT ; Send rate
XRA A ; Say rate is ok
RET
;.....
;
; end
;-----------------------------------------------------------------------
