; B5OX-2.INS - BYE5 insert for Osborne Executive
;
;               Note: This is an insert, not an overlay
;
;               This INSert will work ONLY with BYE509 and above
;
;=   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
; 07/07/86      Overhauled the insert to be compatible with BYE509
;               and later releases having proper CP/M Plus support:
;               - Removed WINDOW configuration parameter as that
;                 function should be provided in the software that uses
;                 the window.
;               - Removed MDPREP/MDPOSP routines as they are no longer
;                 required.
;                                       - George Peace
;
; 08/17/85      - Updated BYE+ version 6 to be compatible with BYE5.
;                                       - George Peace
;=   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;-----------------------------------------------------------------------
;
; Set base port for SIO & Clock chips
;
BASEP   EQU     0CH             ; Base port for sio
BASEC   EQU     04H             ; Base port for baud rate generator
;
; The following define the port addresses to use.
;
DATPORT EQU     BASEP           ; Data port
STPORT  EQU     BASEP+1         ; Status/control port
BPORT   EQU     BASEC           ; Baud rate port
;
;
; Second Byte of 8253 Command:
;
BDCMD1  EQU     1               ;  300 baud
BDCMD2  EQU     0               ; 1200 bps
BDCMD3  EQU     0               ; 2400 bps
BDCMD4  EQU     0               ; 4800 bps
BDCMD5  EQU     0               ; 9600 bps
;
;
; The following are baud rates for BPORT
;
B300    EQU     128             ;  300 baud
B1200   EQU     96              ; 1200 bps
B2400   EQU     48              ; 2400 bps
B4800   EQU     24              ; 4800 bps
B9600   EQU     12              ; 9600 bps
;
;
;-----------------------------------------------------------------------
;
; Is there a carrier?  If not, return with the zero flag set.
;
MDCARCK:MVI     A,10H           ; Reset status
       OUT     STPORT
       IN      STPORT          ; Get status
       ANI     8               ; Check for data carrier
       RET                     ; Return
;.....
;
;
; This routine will turn off the serial card and hang up the phone.
;
MDINIT: MVI     A,18H           ; Reset channel
       OUT     STPORT
       MVI     A,4             ; Setup to write register 4
       OUT     STPORT
       MVI     A,44H           ; 16x, 1 stop bit, no parity
       OUT     STPORT
       MVI     A,1             ; Setup to write register 1
       OUT     STPORT
       MVI     A,0
       OUT     STPORT
       MVI     A,5             ; Setup to write register 5
       OUT     STPORT
       MVI     A,0             ; Clear DTR causing hangup
       OUT     STPORT
       PUSH    B               ; Save in case it's being used elsewhere
       MVI     B,20            ; 2 second delay
;
OFFTI:  CALL    DELAY           ; 0.1 second delay
       DCR     B
       JNZ     OFFTI           ; Keep looping until finished
       POP     B               ; Restore bc
       MVI     A,3             ; Setup to write register 3
       OUT     STPORT
       MVI     A,0C1H          ; Initialize receive register
       OUT     STPORT
       MVI     A,5             ; Setup to write register 5
       OUT     STPORT
       MVI     A,0EAH          ; Turn on DTR so modem can answer phone
       OUT     STPORT
;
        IF     IMODEM          ; If using hayes 300/1200 smartmodem
       CALL    IMINIT          ; Go initialize smartmodem now
        ENDIF                  ; IMODEM
;
       RET                     ; Return
;.....
;
;
; Input a character from the modem port.
;
MDINP:  IN      DATPORT         ; Get character
       RET                     ; Return
;.....
;
;
; Check the status to see if a character is available.  Return with the
; zero flat set, if not.  If yes, use 0FFH to clear the flag.
;
MDINST: IN      STPORT          ; Get status
       ANI     1               ; Got a character?
       RZ                      ; Return if none
       ORI     0FFH            ; ..otherwise, set the proper flag
       RET                     ; ...and return
;.....
;
;
; Send a character to the modem.
;
MDOUTP: OUT     DATPORT         ; Send it
       RET                     ; Return
;.....
;
;
; See if the output is ready for another character.
;
MDOUTST:IN      STPORT
       ANI     4               ; Mask it
       RET                     ; Return
;.....
;
;
; Reinitialize the modem and hang up the phone by dropping DTR and
; leaving it inactive.
;
MDQUIT:  IF     IMODEM          ; If using a smartmodem
       CALL    IMQUIT          ; Tell it to shut down
        ENDIF                  ; IMODEM
;
;
; Called by the main program after the caller types BYE.
;
MDSTOP: MVI     A,5             ; Setup to write register 5
       OUT     STPORT
       MVI     A,44H           ; 16x, 1 stop bit, no parity
       OUT     STPORT
       RET
;.....
;
;
; If you do not support a partiuclar baud rate, put it here before
; SETINV:
;
SETINV: ORI     0FFH            ; Make sure zero flag is not set
       RET                     ; Return
;.....
;
;
SET300: MVI     A,BDCMD1        ; Get second byte of command
       PUSH    PSW             ; ..store it
       MVI     A,B300          ; Load rate
       JMP     SETBAUD
;
SET1200:MVI     A,BDCMD2        ; Get second byte of command
       PUSH    PSW             ; ..save it
       MVI     A,B1200         ; Load rate
       JMP     SETBAUD
;
SET2400:MVI     A,BDCMD3        ; Get second byte of command
       PUSH    PSW             ; ..store it
       MVI     A,B2400         ; Load rate
;
SETBAUD:OUT     BPORT           ; Send first byte of command
       POP     PSW             ; Restore the rate
       OUT     BPORT           ; Send second byte of command
       XRA     A               ; Say rate is OK
       RET                     ; Return
;.....
;
;                              end
;-----------------------------------------------------------------------