; B3EA-2.INS - Eagle II and Eagle III insert for BYE3 - 07/30/85
;
; Z80 SIO and CTC 8340 timer
;
; Note: This is an insert, not an overlay.
;
; This version is for the Eagle II and III computers using channel "A"
; Z80 SIO. The Z80-CTC is used as the baud rate generator.
;
;
; NOTE: The Eagle does not support DTR on pin 20 or DCD on pin 8, so
; be sure you wire the modem cable like this:
;
; modem Eagle
;
; TXD 2 --> 3 RXD
; RXD 3 <-- 2 TXD
; GND 7 --- 7 GND
; DCD 8 --> 5 CTS
; DTR 20 <-- 4 RTS
;
; = = = = = = = = = = = = = = = = = =
;
; Note: For Port A, Data = 18H, CTC = 01H, Port B, Data = 1AH, CTC = 02H
;
DPORT EQU 18H ; Data port
SPORT EQU DPORT+1 ; Status/control port
BRPORT EQU 01H ; Baud rate port
;
DAV EQU 00000001B ; Data available
TBMT EQU 00000100B ; Transmit buffer empty
DCD EQU 00100000B ; Data carrier detect
;
BD300 EQU 47D0H ; 62400/300 (first half is CTC command)
BD1200 EQU 4734H ; 62400/1200
BD2400 EQU 471AH ; 62400/2400
;
;-----------------------------------------------------------------------
;
; See if we still have a carrier - if not, return with the zero flag set
;
MDCARCK:MVI A,10H ; Reset status
OUT SPORT
IN SPORT ; Get status
ANI DCD ; Check for data carrier
RZ
ORI 255
RET
;
; Disconnect and wait for an incoming call
;
MDINIT: MVI A,18H ; Reset channel
OUT SPORT
MVI A,4 ; Setup to write register 4
OUT SPORT
MVI A,84H ;*1 stop, 8 bits, no parity, 32x
OUT SPORT
MVI A,5 ; Setup to write register 5
OUT SPORT
MVI A,68H ; Clear RTS causing hangup
OUT SPORT
;
PUSH B ; Save in case it's being used elsewhere
MVI B,20 ; 2 seconds delay to drop any carrier
OFFTI: CALL DELAY ; 0.1 second delay
DCR B
JNZ OFFTI ; Keep looping until finished
POP B ; Restore bc
;
MVI A,3 ; Setup to write register 3
OUT SPORT
MVI A,0C1H ; Initialize receive register
OUT SPORT
MVI A,5 ; Setup to write register 5
OUT SPORT
MVI A,0EAH ; Turn on RTS so modem can answer phone
OUT SPORT
;
IF IMODEM ; If using intelligent modem
CALL IMINIT ; Go initialize
ENDIF ; IMODEM
;
RET
;
; Input a character from the modem port
;
MDINP: IN DPORT ; Get character
RET
;
; Check the status to see if a character is available. If not, return
; with the zero flag set. If yes, use 0FFH to clear the flag.
;
MDINST: IN SPORT ; Get status
ANI DAV ; Check receive ready bit
RZ ; Return if none
ORI 255 ; Otherwise, set the proper flag
RET
;
; Send a character to the modem
;
MDOUTP: OUT DPORT ; Send it
RET
;
; See if the output is ready for another character
;
MDOUTST:IN SPORT
ANI TBMT ; Check transmit ready bit
RZ
ORI 255
RET
;
; Reinitialize the modem and hang up the phone by dropping DTR and
; leaving it inactive.
;
MDQUIT: IF IMODEM ; If using a smartmodem
CALL IMQUIT ; Tell it to shut down
ENDIF ; IMODEM
;
;
; Called by the main program after caller types BYE
;
MDSTOP: MVI A,5 ; Setup to write register 5
OUT SPORT
MVI A,68H ; Clear RTS causing shutdown
OUT SPORT
RET
;
; The following routine sets the baudrate. BYE3 asks for the maximum
; speed you have available.
;
SET300: LXI H,BD300 ; Get 300 bps parameters in 'HL'
JMP LOADBD ; Go load them
;
SET1200:LXI H,BD1200
JMP LOADBD
;
SET2400:LXI H,BD2400
;
LOADBD: MOV A,H ; CTC command word
STA BRPORT
MOV A,L ; Baudrate
STA BRPORT
XRA A
RET
; end
;-----------------------------------------------------------------------
