NSTAMP.LIT (C) 1988 By Ami Bar-Yadin (512) 631-2277
AMUS ID: AMI/AM
Syntax:
STAMP file{/switches} .... {!text}
File extension defaults to .LOG
If the file does not exists it will be created.
Message text:
Anything between the switches and the "!" is ignored.
If "!" is present in the command line, anything between it and the
end of the line or a "+" (see below) is considered text.
Spaces after the "!" are included in the output.
If "!text" is not on the command line, the user will be prompted
for text by the program, allowing lower case letters to be handled.
The text may be continued over as many line as needed by terminating
each input line, except the last, with a "+".
Each line will be written to the file individualy, that is followed
by a CR/LF pair. You may override this by terminating a line
with "++" which will cause this line to be written WITHOUT the CR/LF.
"+" and "++" may be used in the optional command-line text as well.
Continuation lines are written to the file as is, that is with any
leading/trailing spaces present.
Anything after a "+" or "++" is ignored.
Switches:
Switches may be repeated as often as desiredeach (output)switch
will output its associated data to the output file.
Switches may be combined, but some care might be required as some
letters (especially C, S and T) are a bit overworked here.
i.e. /SDJTTC
means output date only stamp, job name followed by TAB, and terminal
name followed by a comma. Notice that two Ts are required in order
for the second T to be properly recognized as a switch instead of an
option. Of course
/SD/JT/TT
is valid also, has the same meaning, and is much less confusing.
/A Abort if output file does not exists
/E{X} Echo output to terminal (only if output is written to file, that is
only if there are no command line errors)
If "/EX" is used no file output will be performed. Usefull for debugs
/C Output a CR/LF pair
/G[ w | An | C | S | T ]
Set global padding default for output switches
The padding parameter can be one of the following:
w is a decimal number specifying field width (1..50)
(Note: scan is stopped on the first invalid character)
i.e. /G10
Data will be padded on the right with spaces to the width
specified. If the text is too long it will be truncated.
/G by itself is same as /G0.
A padding default of 0 (i.e. /G0) is special. The default
field width of the particular output switch will be used.
This is the usual behavior of the program.
(See main description of P switch belowand also the
descriptions of the output switches J,T,D,L,P,U,V,I,F.)
An Add n to default field width
n is a decimal number
This is the same as w, except that the width used is the
default width for a field plus n
The resulting width must be 1..50if it is larger than 50
a width of 50 will be used
i.e. /GA2
NOTE: /GAn is IGNORED by /F
C Comma padding
Output data without trailing spaces, followed by a comma
i.e. /GC
S Space padding
Output data followed by one space
i.e. /GS
T TAB padding
Output data without trailing spaces, followed by a TAB
i.e. /GT
Switches J,T,D,L,P,U,V,I,F (see below) all take an optional padding
parameter. The syntax is always identical to the P switch syntax.
i.e. /JT will output the job name followed by a TAB
The default of all output switches is to output data in a fixed
field whose width is equal to the maximum length the data can have.
For example 6 characters for job name, 30 characters for AlphaBASE
user name, etc.
I.e. /J will output the job name as a 6 character field
The G switch allows this default to be changed. The default, whether
from a G switch or the program's natural defualt, can always be over-
ridden for any switch individualy. If a fixed width default is given
(i.e. /G10) any data that is longer will be truncated unless there
is a different padding parameter in that particular switch.
I.e. /IG10TL15J
means: output AlphaBASE user ID (fixed width of 6)
set the default padding to a fixed width of 10
output terminal name (fixed width 10)
output logged in device/drive/PPN (fixed width 15)
output job name (fixed width of 10).
This switch is the only way to alter the padding of date/time stamps
from the usual TAB.
/S[n | ^s | m]
Output date/time stamp with optional output mode ($ODTIM flag bits).
<<< (NOT IMPLEMENTED, YET)
<<< Default mode is Whole which gives "Wed 02-Apr-86 16:28:47"
<<< i.e. /S by itself is same as /SW
<<<
<<< (NOT IMPLEMENTED) /SJ will think J is a stamp mode option
<<< and give an error message
<<< /S/J will also result in an error message
Mode can be given in the following formats:
m is a mode character and can be ONE of the following:
D DATE ONLY (02-APR-86)
width: 9
T TIME ONLY (16:23:54)
width: 8
W WHOLE (Wed 02-Apr-86 16:24:42)
width: 22
N NORMAL (Wednesday, September 21, 1988 02:34:32 PM
would you believe: 42
B BRIEF (02-APR-86 16:28:47)
width: 18
i.e. /SD output date only stamp
/SB output brief stamp
n is a number in the current radix (HEX or OCTAL)
(Note: scan is stopped on the first invalid character)
NOTE: a leading digit is required
i.e. /S3395 in OCTAL mode
/S0D43 in HEX mode, note leading zero
s is a string of bits (0 or 1N or Y)
(Note: scan is stopped on the first invalid character,
and spaces are skipped)
i.e. /S^100100011110110
/S^ 100 1000 1111 0110 is also ok
The padding used for date stamp depends on the type of stamp used:
If a binary format (n or ^s) is used the stamp is written followed
by one space.
If one of the specific (mode character) stamp types is used, it will
be treated as a fixed length field whose width equals the maximum
possible length for that stamp type.
This can be overridden using the /G switch.
/J[ n | An | C | S | T ]
Output Job name (first column in STAT.LIT display)
/J output job name padded to 6 characters with spaces
6 characters is the default width for job name
/J10 output job name padded to 10 characters with spaces
If n is smaller than length of name, name will be
truncated
/JA2 output job name padded to 8 characters with spaces
6 (the default width) + additional 2 = width of 8
/JC output job name followed by a comma
/JS output job name followed by one space
/JT output job name followed by a TAB
NOTE: The /J syntax can also be used for the following switches:
(Each switch has its own default width)
/T Output terminal name (second column in STAT.LIT display)
Default width: 6 characters
/D Output terminal driver name (sixth column in TRMDEF.LIT display)
Default width: 6 characters
/P Output program name (fourth column IN STAT.LIT display)
Default width: 6
/U Output user name (AMOS 1.3 or latter only)
(Displayed by Dave Pallmann's USTAT (3.0) eighth column
if the U command is used to enable user names display.
USTAT.LIT is available on the AMUS network in [100,125])
Default width: 20 (decimal)
/V Output AlphaBase user name (if GINDTA.SV is in MEM:)
Default width: 30 (decimal)
/I Output AlphaBase user ID (if GINDTA.SV is in MEM:)
Default width: 6
/Ffile Output file name and version
The full file spec will be written followed by a space,
if the file has an AMOS program header, the version will
be written followed by a space.
The spaces may be overriden thru a /G in which case the file
name and the file version are treated as two field written
to the file seperately each with its own padding.
THIS SWITCH HAS NO DEFAULT WIDTH
The defualt pad for this switch is a space (i.e. /GS)
If a /GAn is used it will be IGNORED.
All commercial rights reserved, etc.
If you want to include STAMP with a commercial package,
go right ahead so long as you include the UNCHANGED
source (.m68) with it.
No warranties and/or guarranties of any kind, etc.
Not responsible for damages resulting from the use of this
program, etc.
My employer (United Fashions) has nothing to do with this
program and should not be blamed for it.
I can be reached at:
United Fashions of Texas, Inc.
200 Ash Ave.
McAllen, TX 78501
(512) 631-2277/2276
8am-6pm
