This ppn contains distribution files for two of Macrotech's products:
-- the ADIT, a 4,8,12 or 16 port intelligent I/O board for the AM-100/L
-- the APU, a 16 port serial I/O card for AM2000M, AM1500, AM2000, AM3000.
Last update of these files on the AMUS bulletin board was made 2/2/89 by CK
If you have any questions about version numbers, installation, use of files,
please contact Macrotech support at (805) 527-1692. We will be happy to
assist you in any way that we can.
-----------------------------------------------------------------------------
ADIT DISTRIBUTION FILES:
------------------------
ADDIAG HLP 2 375-612-633-611
ADIT DID 1 615-751-042-340 Dyalog interface driver, use w/DYALOG.LIT
ADIT IDV 6 072-240-505-651 ADIT interface driver, copy to [1,6]
ADIT M68 38 054-016-426-343 Source to ADIT driver,original DMA version
ADITC IDV 7 133-616-357-514 AMOS 1.3c driver, (COMSER monitor calls)
ADITC M68 61 042-236-421-755 Source to ADITC.IDV
ADITIO M68 14 262-030-421-537 Source to driver, non-DMA, I/O mode
ADTEST CMD 2 535-417-727-767 Forces BARBER to ADIT jobs,for ADTEST.INI
ADTEST HLP 2 146-322-611-601 Help for a simple ADIT test
ADTEST INI 6 321-646-324-006 INI for a simple ADIT test
BARBER LIT 4 056-064-230-030 Forces BARBER to ADIT jobs,for ADTEST.INI
DOIT DGO 1 571-421-014-202
FLOW LIT 1 603-431-172-342 XON/XOFF (".FORCE JOB8 FLOW ON"), to [1,4]
MAXTST LIT 2 667-663-577-643 User friendly memory test
MT LIT 7 672-241-642-341 Not documented, but flexible memory test
SPEED LIT 3 635-551-510-233 Like BAUD.LIT, but better
WHOAA LIT 1 615-623-674-207 Enables reverse hardware handshake, [1,4]
Total of 20 files in 179 blocks
---------------------------------------------------------------------------
APU DISTRIBUTION FILES:
----------------------
APU ASD 1 661-747-020-174 REV 1.0(101) for AUTOLOG, to [7,0]
APU DIR 2 223-632-273-640 For use with "VERIFY" command
APU HLP 3 140-212-630-017 Help file for APU installation
APU IDV 7 770-257-127-550 Rev 1.1 APU16 interface driver, [1,6]
APUTST CMD 1 413-537-340-152 Forces BARBER to APU16 ports, to [2,2]
APUTST INI 7 030-356-215-562 Test INI for APU16, to [1,4]
BARBER LIT 4 056-064-230-030 Forces BARBER output to jobs, to [1,4]
SETAPU LIT 2 245-776-134-076 Use with APU.IDV Rev. 1.1, to [1,4]
SPEED LIT 3 635-551-510-233 Like BAUD.LIT, but better
Total of 13 files in 54 blocks
Notes on the APU:
-- Use with AMOS 1.0D, 1.3D or later
-- If you encounter problems at TRMDEF time, be sure you are using an
up-to-date version of TRMDEF.LIT. Use Rev 1.1(121) or later.
-- To turn on enhanced mode (used only when APU's are not mixed with
AM-355's on the I/O cable), place the following statement in the
.INI after the SYSTEM command:
.SETAPU ENHANCED
This command may also be typed in at AMOS level after system boot-up.
Enhanced mode may be turned off at any time with the command:
.SETAPU NORMAL
