 |
Return Create A Forum - Home |
 |
--------------------------------------------------------- |
|
Lynx Wind Forum |
 |
https://lynxwindforumhtml.createaforum.com |
|
--------------------------------------------------------- |
|
***************************************************** |
|
Return to: Anything off topic |
|
***************************************************** |
|
#Post#: 2214-------------------------------------------------- |
|
something new from something old an recycled |
|
By: happygolucky Date: April 12, 2014, 2:31 pm |
|
--------------------------------------------------------- |
|
i noticed the other half lay by the road side from last month it |
|
was still there calling out.. today! so i took it as a divine |
|
inspiration/intervention an good deed.. as i was coming home |
|
from church i said its still there.. |
|
now i have been looking an tinkering with an idea to turn my |
|
little 400 watt 24v dc motor this is very rough in the think |
|
tank stage.... but i think you can see where i'm heading... |
|
horizontal with a fin for direction.. or vertical...... this is |
|
what i was talking about when i mentioned the base..add dual |
|
alternators an drive my dc motor... these do not match off to |
|
different chars one is lighter so this may work to my advantage, |
|
but they still will work..my wife is using the matching one an |
|
said hands off...my office chair ! |
|
now there are many friction less an directionless way's to |
|
rotate this plastic polymer poly-carbon base.. practically pre |
|
-assembled ready for recycled applications ...something new from |
|
something old..thanks dad..my mentor.... with very minor |
|
alterations ..i can mechanize it... using super bearings on a |
|
shaft both halves fit like a Glove an are on same center-line |
|
axis point to point..... i just need to energize it with |
|
motion... i believe in simplicity an efficiency... i can work |
|
with both..the path with least resistance an friction. |
|
use water i do have ... but i need to enclose an recycle wish i |
|
had a stream.. .. wind i do have..45 to 50 mph at times once a |
|
month average ...mostly 10-20 mph constant with gust ..steam |
|
threw a boiler.. air pressure ect. |
|
#Post#: 2238-------------------------------------------------- |
|
Re: something new from something old an recycled |
|
By: happygolucky Date: April 13, 2014, 6:47 pm |
|
--------------------------------------------------------- |
|
now i have it..i found out i could please too people at |
|
once..the base was interchangeable..she got tokeep her chair an |
|
i got the match i needed ;D |
|
MACgyver engineering @ its best AN A COUNTRY BOY CAN |
|
SURVIVE..... |
|
now i have a turbine permanent magnet motor 400 watt 24v 22amp |
|
vawt /hawt |
|
all i need is 5 rods threaded both ends ...a few bearings an the |
|
other sprocket which i have an chain..or i can shaft alignment |
|
couple.. or i can make a 3 phase dual /single phase alternator |
|
decisions decisions.. |
|
dimensions are as follow width is 24"/ dia X 24-60" length |
|
#Post#: 2309-------------------------------------------------- |
|
Re: something new from something old an recycled |
|
By: happygolucky Date: April 16, 2014, 8:31 pm |
|
--------------------------------------------------------- |
|
ran into a bit of a snag today, i have wrestled with this idea |
|
before... how big do i go...... i do not know? but here it |
|
goes... in my project bigger is better so i'm told by experience |
|
..i need a larger diameter size .. i have a dia. of 2'an not |
|
enough torque.... fine for water flow..to turn my little |
|
generator depending on flow rates an size that can happen... do |
|
but wind is different... |
|
i have a problem with torque not enough ....explained in in |
|
this way.. under a load! there is going to be even more torque |
|
.... so i have been advised to extend my circumference to a |
|
minimum of up to 8' in diameter an height of 5-6...' this |
|
changes everything a bit... a light goes off (a water Ferris |
|
wheel gravity fed hmmm ???...)maybe>then once i achieve this |
|
stage i will need to stop it ! easy stop the water.. |
|
second situation arises how to stop wind..? |
|
know my chair base shall become a top an bottom mounting |
|
bracket or i extend the arms length.... to a large circumference |
|
with a hub centered /attached to a shaft an gear attached to a |
|
hub (back to the gear formula ratio? now do i need a larger |
|
sprocket/gear hmm i don't think so..) at the bottom off the |
|
hub. |
|
i have the idea that more mass equates to greater speed an |
|
torque we will see.. as the material will go larger ... more |
|
surface area? less drag ? more torque? makes sense.. to my |
|
permanent motor magnet generator dc |
|
we will see...i may taking a drive to metro to look at there's |
|
up close.. |
|
***************************************************** |
