Introduction
Introduction Statistics Contact Development Disclaimer Help
Return Create A Forum - Home
---------------------------------------------------------
CycleKarts GB
https://cyclekartsgb.createaforum.com
---------------------------------------------------------
*****************************************************
Return to: Design Files
*****************************************************
#Post#: 8247--------------------------------------------------
Wheel Nut Spinners
By: Moogie38 Date: February 19, 2023, 12:17 pm
---------------------------------------------------------
Latest wee project, made to fit Honda ANF 125 wheels.
[attach=3]
Could someone with Honda C90 wheels measure the centre huub
diameter please? See image below.
[attach=2]
#Post#: 8253--------------------------------------------------
Re: Wheel Nut Spinners
By: peterL Date: February 20, 2023, 2:25 pm
---------------------------------------------------------
Hi Noel,
Mine taper very slightly from 44mm to 44.5mm.
The depth is around 4.5mm before it curves into the backplate.
Total projection of the hub is 7mm, including the bottom radius
where it curves into the backplate.
[attach=1]
Hope this helps, if you need anything further let me know.
I have mounted with that face pointing inwards, as I am fitting
dummy brake drums, and the four bolt holes are ideal.
Wouldn't mind a copy of the stl file though :)
Peter
#Post#: 8255--------------------------------------------------
Re: Wheel Nut Spinners
By: Moogie38 Date: February 20, 2023, 3:02 pm
---------------------------------------------------------
Thanks Peter, once I get a test print done and make sure
everything is OK, I'll put the STLs up on Thingiverse and add a
link on here.
#Post#: 8261--------------------------------------------------
Re: Wheel Nut Spinners
By: Moogie38 Date: February 21, 2023, 2:54 pm
---------------------------------------------------------
10 hours of print time and i have 1 spinner !
[attach=1]
[attach=2]
Normally i print at 0.1mm layer height but the print would have
taken 20+ hours so upped the layer height to 0.2mm and that
brought the time down to around 10 hours.
The Honda ANf wheels have a slightly different size of centre
protrusion so i ended up having to make slightly different sized
spinner for front and rear wheels.
Also added a couple of little hole to accept 4mm grub screws to
enable fixing to wheel.
[attach=3]
[attach=4]
[attach=5]
STLs are now up on Thingiverse.
https://www.thingiverse.com/thing:5869231/files
#Post#: 8262--------------------------------------------------
Re: Wheel Nut Spinners
By: Glynn Date: February 22, 2023, 10:49 am
---------------------------------------------------------
The Austin 7 never had knock on wheels, they were bolted on and
some had hubcaps.
So I've made some replica hub caps instead.
#Post#: 8263--------------------------------------------------
Re: Wheel Nut Spinners
By: Glynn Date: February 22, 2023, 10:50 am
---------------------------------------------------------
They fit the Fun Bikes wheels
#Post#: 8264--------------------------------------------------
Re: Wheel Nut Spinners
By: sylvaman Date: February 22, 2023, 11:51 am
---------------------------------------------------------
Look Great, Glynn . Do i spy a Green painted body , behind
those wheels ? ;D
#Post#: 8265--------------------------------------------------
Re: Wheel Nut Spinners
By: Glynn Date: February 22, 2023, 12:18 pm
---------------------------------------------------------
Yes, been painting this week. Should have it finished this
weekend. All ready for Gaydon.
#Post#: 8269--------------------------------------------------
Re: Wheel Nut Spinners
By: Moogie38 Date: February 22, 2023, 3:26 pm
---------------------------------------------------------
Wee test to see how my chrome spray paint will look. If it was
sanded and filled i would look the part.
#Post#: 8270--------------------------------------------------
Re: Wheel Nut Spinners
By: jim Date: February 22, 2023, 11:43 pm
---------------------------------------------------------
They look the dogs danglies Noel. I want some for my pit bike
wheels.
*****************************************************
Next Page
You are viewing proxied material from gopher.createaforum.com. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.