Introduction
Introduction Statistics Contact Development Disclaimer Help
Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
Return to: Chainsaws not listed - Gas OPE
*****************************************************
#Post#: 91331--------------------------------------------------
Farmertec G2511
By: Chainsawrepair Date: May 10, 2025, 5:57 am
---------------------------------------------------------
The JonCutter 2511 is farmertec version of the echo clone 2511
Right now $49 plus ship from China which doubles that with
tariff tax added in.
https://www.farmertec.com/US-STOCK-25cc-JonCutter-G2511-Top-Handle-Arborist-Gas…
8.html
#Post#: 91420--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 9, 2025, 3:32 pm
---------------------------------------------------------
Yes Joncutter put the right blue filter the clones suppose to
have. Sweet
$99 shipped right from US warehouse.
Echo V805000150
Screw, 5 X 16 T27
Echo A312000090
Exhaust Heat Shield
Echo V104002290
Exhaust Gasket
#Post#: 91444--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 17, 2025, 5:52 am
---------------------------------------------------------
Farmertec G2511 Joncutter G2511
Can never have to many of the little 25cc saws. Farmertec G2511
aka Joncutter G2511 echo 2511 clone.
Just like the V-modest one so far comparing and looking over in
Farmertec colors.
12" to 42" covered, 25cc to 119cc :ROFLMAO: ✌️
3/8LP 1/4" mini 325 Nano all 3 sets now to compare at once for
fun.
I swear it crawled up beside the G3120 and said daddy.
😂🍻
Farmertec 2511 PHO weight dry
#Post#: 91448--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 18, 2025, 5:29 am
---------------------------------------------------------
Echo clone 2511 25cc just started 2nd tank and only $99 bucks
shipped stock.
https://youtu.be/vIEEaPxF_-o
#Post#: 91453--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 18, 2025, 1:02 pm
---------------------------------------------------------
Something I learned to do on oem echo�s and clone versions.
Grease at matting points and orings. I do it on 2511�s 501�s
4910 490 590 etc.
Clones with blue filter 2511 #113 on clones
Oring makes fit better and grease stops fines.
If any getting by the 2 halves grease there too.
No reason to spend money on fixes when you most likely have
everything to do it free like me.
8.57 Egan pipe on oem echo closed port nano 325 ----- 10.68
clone Farmertec open port nano 325 stock muffler. With stihl
63PS 11.16 fastest on Farmertec 2511
8x8 pine dry so like 9" round
So I seen about 20% between oem with pipe v/s stock clone.
#Post#: 91455--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 18, 2025, 5:51 pm
---------------------------------------------------------
The fastest run on 325 nano was quicker then the 3/8LP full
chisel. Rest of the runs were slower.
But I only kept the fastest run from each. 325 quickest 10.68,
3/8LP FC 11.16,1/4 MM 12.61 on stock 2511's.
325 and 1/4 smoothest and 1/4" wins that part.
https://youtu.be/Q8a3zlaP7io
https://youtu.be/SnIh4dIh3s4
#Post#: 91461--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: June 20, 2025, 9:13 am
---------------------------------------------------------
Timing the new Joncutter 2511 open port with their stock open
muffler with small pipe. Put on the nano set up.
Then ran the OEM echo 2511 closed port with the Egan pipe that
tested 28% better stock then the echo stuffed mufflers they use
on them. Also new nano set up.
Cutting clean cant pine dry 8x8 which is around 9" round.
Fastest cuts there was only 2 seconds difference. 20% difference
in cuts between them. I am almost betting the clone would beat
the oem if it had that awful stuffed up stock muffler on it.
Not bad for a $99 shipped saw compared to over $500 saw.
#Post#: 91521--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: July 24, 2025, 8:22 am
---------------------------------------------------------
Going to see if the precision saw service polar port PSS V2
makes a difference over the already open clone 2511 muffler with
small pipe.
IMO it is the better design of the cnc mufflers out there. I
just dont see that wcs one flowing like this one.
https://www.precisionsawservice.com/shopproducts/p/2511-performance-muffler-ver…
Guys putting on the Egan pipe on clone 2511say they feel same
type of gains as oem 2511.
#Post#: 91523--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: July 25, 2025, 9:18 am
---------------------------------------------------------
Measured those ID of the echo 2511 mufflers.
In pic.
#Post#: 91524--------------------------------------------------
Re: Farmertec G2511
By: Chainsawrepair Date: July 26, 2025, 6:14 am
---------------------------------------------------------
Getting ready to test a oem stock muffler, clone muffler, egan
pipe, pps V2, wcs ones.
Prob have the wcs one next week to throw in the test.
Also in thread in my group. The PSS V1 that was made before the
V2 by the NY member was 11mm ID to compare. So it was just hair
bigger then clone ones.
Glad he made the V2 ones shown size above. Another guy in my
group said he is doing 17mm on his ported ones.
*****************************************************
Next Page
You are viewing proxied material from gopher.createaforum.com. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.