Introduction
Introduction Statistics Contact Development Disclaimer Help
Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
Return to: Pioneer
*****************************************************
#Post#: 37882--------------------------------------------------
Pioneer p41 chain saw parts
By: Bob Date: April 1, 2014, 12:57 pm
---------------------------------------------------------
Hi,
Does anyone know where I can find new or good used parts for a
Pioneer p41? Thought I found parts on ebay but they had already
sold.
Looking for the following:
47355 piston
430410 rings
430924 cylinder head or cylinder head kit
Thank you,
Bob
#Post#: 37888--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: KilliansRedLeo Date: April 1, 2014, 2:03 pm
---------------------------------------------------------
I rebuilt a P-41 a year or so ago, these guys had all the parts
I needed in stock.
http://rottmansales.com/
#Post#: 37893--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: Bob Date: April 1, 2014, 2:51 pm
---------------------------------------------------------
Thanks Killian,
Rottman's said it comes as a kit, the kit contains a flywheel,
cylinder and coil, piston and rings are additional and you have
to change the flywheel &coil for the new cylinder.
Do you have to replace your cylinder & piston?
Thank you,
Bob
#Post#: 37894--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: KilliansRedLeo Date: April 1, 2014, 2:56 pm
---------------------------------------------------------
The need to replace the C/P depends on if your is messed up. I
did the whole thing because that is what the customer wanted.
Some of the very early ones used points ignition. My
recommendation would be to go to electronic ignition which
requires a different cylinder that is why it is in the kit. Also
make sure you replace the reeds and reed box gasket.
If you have never run a P-41, you will like it, very nice
powerful saws!
#Post#: 37898--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: Bob Date: April 1, 2014, 3:17 pm
---------------------------------------------------------
Thanks Killians,
Yes piston & cylinder are trashed, flywheel and coil are ok, was
just wondering why they to be replaced because of the new
cylinder? Does the new piston have to go in a certain way, in
other words does it matter which side of the piston faces the
exhaust port?
Was a favorite saw of mine, took good care of it till I loaned
it to my father pretty sure he put regular gas in it when he
gave it back had no compression.
This is becoming a costly restore.
Thank you for all your help I really appreciate it.
Bob
#Post#: 37906--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: KilliansRedLeo Date: April 1, 2014, 7:07 pm
---------------------------------------------------------
Bob, too bad about the raw gas situation. Yes the piston only
goes in one way, there is usually an arrow on the top of the
piston that is supposed to point to the exhaust port.
#Post#: 37910--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: 660magnum Date: April 1, 2014, 8:07 pm
---------------------------------------------------------
I don't know about the P-41 but some western European chainsaw
pistons have the arrow pointing towards the intake side with a
big capital "E" imprinted at the arrow. The "E" is for Enlass or
"Intake" in English.
The bottom line is to look for the ring pins. The ring pins must
be where they do not come across a port!
#Post#: 37915--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: KilliansRedLeo Date: April 1, 2014, 8:50 pm
---------------------------------------------------------
Good post Jim, +1!
#Post#: 37926--------------------------------------------------
Re: Pioneer p41 chain saw parts
By: fordfairlane78 Date: April 2, 2014, 2:38 am
---------------------------------------------------------
Tommysp1 has pioneer parts as well. This is a member on this
site. Have you already torn down the saw and confirmed that the
p/c are toast? I don't remember if the p 41 had a compression
release or if it had the automatic release engaged by the rope
pulley but these could be problems if you don't already know if
the p/c are bad....
*****************************************************
You are viewing proxied material from gopher.createaforum.com. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.