___    ___    _   ___  ___
         (  _`\ (  _`\ (_)(  _`\ (  _`\
         | (_) )| (_(_)| || ( (_)| (_(_)
         |  _ <'|  _)_ | || |___ |  _)_
         | (_) )| (_( )| || (_, )| (_( )
         (____/'(____/'(_)(____/'(____/'
     ___    _____  _    _  _          _
    (  _`\ (  _  )( )  ( )( )________( )
    | (_) )| ( ) |`\`\/'/'|            |
    |  _ <'| | | |  >  < (  n3cr0man3r  )
    | (_) )| (_) | /'/\`\ |  ________  |
    (____/'(_____)(_)  (_)(_)        (_)

______________________________________________
(Note: This is no copy paste, its the real deal)
(     If you can't figure it sucks for you     )

_______
(History):


A beige box (or lineman's handset) can be used to
use any fone line you can get to, tap into a fone
line you can get to & also check the status of
fone lines (what ma bell uses em for). In this
document I'm going to teach you how to make one.

________
(Supplies):

        ______
       (Tools:)
         7/16 Hex Driver
         Wire-cutters/Strippers
             Soddering iron & Sodder
             Knife
             Lighter
        ______
       (Stuff:)
             Small fone w/in use light and modular jack
             2 Aligator Clips (1 red and 1 green)
             Modular fone cord
             Heatshrink tubing

___________
(Building It):

        _
       (1):Cut off one end of the modular fone cord and
           remove some of the casing plastic. You should
           see 4 wires, 1 red, 1 green, 1 yellow, 1 black.

        _________________
       (Modular fone cord)
    _______
       |       |
       | ____  |
       |(Cord) |
       |       |
       |       |
       |       |
       |       |
       |       |
       |_______|
        | | | |
        | | | | <---4 wires, 1 red, 1 green, 1 yellow, 1 black
        | | | |
        | | | |
        | | | |

        _
       (2):Strip the red and green wires, and cut off the yellow
           and black ones.

        _________________
       (Modular fone cord)
    _______
       |       |
       | ____  |
       |(Cord) |
       |       |
       |       |
       |       |
       |       |
       |       |
       |_______|
        | |
        | | <---2 stripped wires, 1 red and 1 green
        | |
        | |
        | |

       _
      (3):Cut off one end of one of the aligator clips and strip
          it. Then repeat that with the other clip.

       _
      (4):Sodder the end off the green aligator clip to the green
         wire, then do the same with the red clip.

        _________________
       (Modular fone cord)
    _______
       |       |
       | ____  |
       |(Cord) |
       |       |
       |       |
       |       |
       |       |
       |       |
       |_______|
        | |  <---2 stripped wires soddered to the ends of aligator clips,
        | |      1 red and 1 green
       () ()
        | |
        | |

      _
     (5):Shrink the heat sink tubing around the exposed wires now you
         have the finished fone cord.

        _________________
       (Modular fone cord)
    _______
       |       |
       | ____  |
       |(Cord) |
       |       |
       |       |
       |       |
       |_______|
       | ____  |
       |(Tube) |
       |_______|
        |     |
        |     |
        |     |
        |Clips|
        |     |
        |     |
        |     |
        |_   _|
   (  ) (  )
    ||   ||
    ||   ||

     _
    (6):Plug the cord into the fone, you have just build a beige box.


________
(Using It):

This device can be any
of several Bell switching apparatus that include terminal sets
(i.e., remote switching centers, bridging heads, cans, etc.)  To open
most Bell Telefone switching apparatus, you must have a 7/16 inch hex
driver.  This piece of equipment can be picked up at your local
hardware store.  With your 7/16 hex driver, turn the security bolt(s)
approximately 1/8 of an inch counter-clock- wise and open.
If your output device is locked, then you must have some knowledge
of destroying and/or picking locks.  However, we have never encoun-
tered a locked output device.  Once you have opened your output device, you
should see a mass of wires connected to terminals.  On most of your output
devices, the terminals should be labeled "T" (Tip -- if not labeled, it is
usually on the left) and "R" (Ring -- if not labeled, it is usually on the
right).  Remember: Ring - red -  right.  The "Three R's" -- a simple way to
remember which is which. Now you must attach the red alligator
clip (ring) to the "R" (ring) terminal.  Attach the green
alligator clip (tip) to the "T" (tip) terminal.

Now your box is basicly a phone of the building the box you attached
your box to. You can ease drop on conversations in that building, make
free calls etc. Its up to you what do do with your box.