A & B LEADS
Designation of leads derived from the midpoints of the two
pairs comprising a 4-wire circuit.
ABBREVIATED DIALING
Preprogramming of a caller's phone system or long distance
company's switch to recognize a 2- to 4-digit number as an
abbreviation for a frequently dialed phone number, and
automatically dial the whole number.
Synonym: Speed Dialing.
ACCESS CHARGE
Monies collected by local phone companies for use of their
circuits to originate and terminate long distance calls.
Can be per minute fees levied on long distance companies,
Subscriber Line Charges (SLCs) levied directly on regular
local lines, fixed monthly fees for special telco circuits
(ie. WAL, DAL,T-1), or Special Access Surcharge (SAS) on
special access circuits.
ACCESS LINE
A telephone circuit which connects a customer location to a
network switching center.
AIRLINE MILEAGE
Calculated point-to-point mileage between terminal
facilities.
ALL TRUNKS BUSY (ATB) A single tone interrupted at a 120 ipm
(impulses per minute) rate to indicate all lines or trunks
in a routing group are busy.
ALTERNATE ROUTE
A secondary communications path used to reach a destination
if the primary path is unavailable.
ALTERNATE USE
The ability to switch communications facilities from one
type to another, i.e., voice to data, etc.
ALTERNATE VOICE DATA (AVD)
A single transmission facility which can be used for either
voice or data.
ANALOG SIGNAL
A signal in the form of a continuous varying physical
quantity, e.g., voltage which reflects variations in some
quantity, e.g., loudness in the human voice.
ANNUNCIATOR
An audible intercept device that states the condition or
restrictions associated with circuits or procedures.
ANSWER BACK
An electrical and/or visual indication to the calling or
sending end that the called or received station is on the
line.
ANSWER SUPERVISION
An electrical signal fed back up the line by the local
telephone company at the distant end of a long distance call
to indicate positively the call has been answered by the
called party. Tells billing equipment to start timing the
call.
AREA CODE
A three digit number identifying more than 150 geographic
areas of the United States and Canada which permits direct
distance dialing on the telephone system. A similar global
numbering plan has been established for international
subscriber dialing.
Synonym: Numbering Plan Area (NPA).
ATTENDANT POSITION
A telephone switchboard operator's position. It provides
either automatic (cordless) or manual (plug and jack)
operator controls for incoming and/or outgoing telephone
calls.
ATTENTUATION
A general term used to denote the decrease in power between
that transmitted and that received due to loss through
equipment, lines, or other transmission devices. It is
usually expressed as a ratio in dB (decibel).
AUDIBLE RINGING TONE
An audible signal heard by the calling party during the
ringing-interval.
AUTHORIZATION CODE
A 5- to 14-digit number entered using a touch-tone phone to
identify the caller as a customer of the long distance
service. Used primarily before Equal Access as a way to
verify the caller as a customer and bill calls.
AUTO ANSWER
A machine feature that allows a transmission control unit or
station to automatically respond to a call that it receives.
AUTOMATIC CALL DISTRIBUTOR (ACD)
A switching system designed to queue and/or distribute a
large volume of incoming calls to a group of attendants to
the next available "answering" position.
AUTOMATIC DIALING UNIT
A device which is programmed with frequently called numbers.
The caller presses one to three digits and the preprogrammed
number is automatically dialed into the phone circuit.
AUTOMATIC IDENTIFICATION OF OUTWARD DIALING (AIOD)
The ability of some centrex units to provide an itemized
breakdown of charges (including individual charges for toll
calls) for calls made by each telephone extension.
AUTOMATIC NUMBER IDENTIFICATION (ANI)
On long distance calls, the process by which the local phone
company passes a caller's local billing phone number to
his/her long distance company when a "1+" or "10-XXX" call
is made. With ANI a caller's long distance carrier knows
who (what phone number) to bill without requiring the caller
to enter any extra digits to be identified.
AUTOMATIC ROUTE SELECTION (ARS)
Synonym: Least Cost Routing
BAND
(1) The range of frequencies between two defined limits.
(2) In reference to WATS, one of the five specific
geographic areas as defined by the carrier.
Synonym: Bandwidth.
BANDWIDTH
see BAND.
BASEBAND The total frequency band occupied by the aggregate of
all the voice and data signals used to modulate a radio
carrier.
BAUD
A unit of signaling speed. The speed in Baud is the number
of discrete conditions or signal elements per second. If
each signal event represents only one bit condition, then
Baud is the same as bits per second. Baud does not equal
bits per second.
BLOCKED CALLS
Attempted calls that are not connected because (1) all lines
to the central offices are in use; or (2) all connecting
paths through the PBX/switch are in use.
BREAK
A means of interrupting transmission, a momentary
interruption of a circuit.
BREAKEVEN POINT
Level of usage at which the total cost of a service with a
high fixed up-front monthly fee but low minute costs becomes
equal to the total cost of another service with low (or
zero) monthly fee but relatively high per minute cost. At
usage levels higher than breakeven, the service with the
high monthly fee is cheaper.
BROADBAND
A transmission facility having a bandwidth of greater than
20 kHz.
BUS
A heavy conductor, or group of conductors, to which several
units of the same type of equipment may be connected.
BUSY
The condition in which facilities over which a call is to be
transmitted are already in use.
BUSY HOUR
The time of day when phone lines are most in demand.
BUSY TONE
A single tone that is interrupted at 60 ipm (impulses per
minute) to indicate that the terminal point of a call is
already in use.
BYPASS
The direct connection to customer-premises equipment by an
IC. This occurs when an IC connects its own facilities (or
facilities leased from a non-BOC entity) directly to an end
user's premises, circumventing the use of the BOC network..
CARRIER
A long distance company which uses primarily its own
transmission facilities, as opposed to resellers which lease
or buy most or all transmission facilities from carriers.
Many people refer to any type of long distance company,
whether it has its own network or not, as a carrier, so the
term is not as restrictive as it used to be.
CARRIER ACCESS CODE (CAC)
The sequence an end user dials to obtain access to the
switched services of a carrier. Carrier Access Codes for
Feature Group D are composed of five digits, in the form
10XXX, where XXX is the Carrier Identification Code.
CARRIER COMMON LINE CHARGE (CCLC)
A per minute charge paid by long distance companies to local
phone companies for the use of local public switched
networks at either or both ends of a long distance call.
This charge goes to pay part of the cost of telephone poles,
wires, etc.
CARRIER IDENTIFICATION CODE (CIC)
The three-digit number that uniquely identifies a carrier.
The Carrier Identification Code is indicated by XXX in the
Carrier Access Code. The same code applies to an individual
carrier throughout the area served by the North American
Numbering Plan.
CARRIER SYSTEM
A system for providing several communications channels over
a single path.
CELLULAR MOBILE RADIO
A high capacity land mobile radio system in which an
assigned frequency spectrum is divided into discrete
channels that are assigned to a cellular geographic serving
area.
CENTRAL OFFICE (CO)
With local telephone companies, the nearby building
containing the local telco switch which provides local
telephone service. Also the physical point where calls
enter the long distance network. Sometimes referred to as
Class 5 office, end office, or Local Dial Office.
CENTREX, CO
PBX Service provided by a switch located at the telephone
company central office.
CENTREX, CU
A variation on Centrex CO provided by a telephone company
maintained "Central Office" type switch located at the
customer's premises.
CHANNEL
A communications path via a carrier or microwave radio.
CIRCUIT A path for the transmission of electromagnetic signals to
include all conditioning and signaling equipment.
Synonym: Facility.
CIRCUIT SWITCHING
A switching system that completes a dedicated transmission
path from sender to receiver at the time of transmission.
CLASS OF SERVICE/CLASS MARK (COS)
A subgrouping of telephone customers or users for the sake
of rate distinction or limitation of service.
COAXIAL CABLE
A cable with a solid outer shield, a space and then a solid
inner conductor. The electromagnetic wave travels between
the outer shield and the conductor. It can carry a much
higher band width than a wire pair.
CODEC
Coder-Decoder. Used to convert analog signals to digital
form for transmission over a digital median and back again
to the original analog form.
COMMON CARRIER
A government regulated private company that provides the
general public with telecommunications services and
facilities.
COMMON CHANNEL INTEROFFICE SIGNALING (CCIS)
A digital technology used by AT&T to enhance their
Integrated Services Digital Network. It uses a separate
data line to route interoffice signals to provide faster
call set-up and more efficient use of trunks.
COMMON CONTROL SWITCHING ARRANGEMENT (CCSA)
The use of carrier switches under a carrier's control as
part of a customer's private network. The carrier's
software controls and switches the customer's calls over
private lines the customer has rented. Control of the
switch and switching functions is done in common for all
users using the software and switching system.
CONDITIONING EQUIPMENT
Equipment modifications or adjustments necessary to match
transmission levels and impedances and which equalize
transmission and delay to bring circuit losses, levels, and
distortion within established standards.
CONFIGURATION
The combination of long-distance services and/or equipment
that make up a communications system.
CONTROL UNIT (CU)
The central processor of a telephone switching device.
COST COMPONENT
The price of each type of long distance service and/or
equipment that constitutes a configuration.
CROSS CONNECTION
The wire connections running between terminals on the two
sides of a distribution frame, or between binding posts in a
terminal.
CROSS TALK
The unwanted energy (speech or tone) transferred from one
circuit to another circuit.
CUSTOMER ACCESS LINE CHARGE (CALC)
The FCC-imposed monthly surcharge added to all local lines
to recover a portion of the cost of telephone poles, wires,
etc., from end users. Before deregulation, a large part of
these costs were financed by long distance users in the form
of higher charges.
CUSTOMER OWNED AND MAINTAINED (COAM)
Customer provided communications apparatus and associated
wiring.
CUSTOMER PREMISE EQUIPMENT (CPE)
Telephone equipment, usually including wiring located within
the customer's part of a building.
CUT
To transfer a service from one facility to another.
CUT THROUGH
The establishment of a complete path for signaling and/or
audio communications.
DATA SET
A device which converts data into signals suitable for
transmission over communications lines.
DATA TERMINAL
A station in a system capable of sending and/or receiving
data signals.
DECIBEL (dB)
A unit measurement represented as a ratio of two voltages,
currents or powers and is used to measure transmission loss
or gain.
DEDICATED ACCESS LINE (DAL)
An analog special access line going from a caller's own
equipment directly to a long distance company's switch or
POP. Usually provided by a local telephone company. The
line may go through the local telco Central Office, but the
local telco does not switch calls on this line.
DELAY DIAL
A dialing configuration whereby local dial equipment will
wait until it receives the entire telephone number before
seizing a circuit to transmit the call.
DELTA MODULATION (DM)
A variant of pulse code modulation whereby a code
representing the difference between the amplitude of a
sample and the amplitude of the previous one is sent.
Operates well in the presence of noise, but requires a wide
frequency band.
DEMODULATION
The process of retrieving data from a modulated signal.
DIAL LEVEL
The selection of stations or services associated with a PBX
using a one to four digit code (e.g., dialing 9 for access
to outside dial tone).
DIAL PULSING
The transmitting of telephone address signals by momentarily
opening a DC circuit a number of times corresponding to the
decimal digit which is dialed.
DIAL REPEATING TIE LINE/DIAL REPEATING TIE TRUNK
A tie line arrangement which permits direct trunk to trunk
connections without use of the attendant.
DIAL SELECTIVE SIGNALING
A multipoint network in which the called party is selected
by a prearranged dialing code.
DIAL TONE
A tone indicating that automatic switching equipment is
ready to receive dial signals.
DIALING PLAN
A description of the dialing arrangements for customer use
on a network.
DIRECT DISTANCE DIALING (DDD)
A basic toll service that permits customers to dial their
own long distance call without the aid of an operator.
DIRECT INWARD DIALING (DID)
A PBX or CENTREX feature that allows a customer outside the
system to directly dial a station within the system.
DIRECT OUTWARD DIALING
A PBX or CENTREX feature that allows a station user to gain
direct access to an exchange network.
DROP
The portion of outside telephone plant which extends from
the telephone distribution cable to the subscriber's
premises.
DRY CIRCUIT
A circuit which transmits voice signals and carries no
direct current.
DUAL TONE MULTI-FREQUENCY (DTMF)
Also known as Touch-Tone. A type of signaling which emits
two distinct frequencies for each indicated digit.
DUPLEX SIGNALING
A long-range bidirectional signaling method using paths
derived from transmission cable pairs. It is based on a
balanced and symmetrical circuit that is identical at both
ends. This circuit presents an E&M lead interface to
connecting circuits.
ECHO
A signal that has been reflected or otherwise returned with
sufficient magnitude and delay to be perceived by the
speaker.
ECHO RETURN LOSS (ERL)
The loss which must be in the echo path to reduce echo to a
tolerable amount.
ECHO SUPPRESSOR
A device which detects speech signals transmitted in either
direction on a four-wire circuit, and introduces loss in the
direction of transmission.
EITHER END HOP OFF (EEHO)
In private networks, a switch program that allows a call
destined for an off-net location to be placed into the
public network at either the closest switch to the
origination or to the destination. The choice is usually by
time of day. Uses either Head End Hop Off or Tail End Hop
Off.
ELECTRONIC KEY TELEPHONE SETS (EKTS)
A generic term indicating key telephones with built-in
microprocessors which allow access to PBX-like features as
well as access to multiple CO lines, using 2 to 4 pair
wiring.
ELECTRONIC SWITCH
Modern programmable switch (often denoted ESS, for
Electronic Switching System) used in most BOC telephone
companies, many independent telephone companies, and by
virtually all new long distance companies. Completely solid
state electronics, as opposed to older electro-mechanical
switches.
ELECTRONIC SWITCHING SYSTEM (ESS)
Used as a station instrument on a PBX. Also a Bell System
term for electronic exchange switching equipment.
ELECTRONIC TANDEM NETWORK (ETN)
(1) A private network automatically and electronically
connecting the calling office to the called office through
Tandem-Tie Trunks. The network switches also function as
PBXs. (2) An AT&T product name. (3) Used as a generic term
for a PBX base network.
ENHANCED PRIVATE SWITCHED COMMUNICATIONS SERVICE (EPSCS)
A private network utilizing Bell provided equipment located
in the central office and dedicated to a specific customer.
E&M LEADS
A pair of leads which carry signals between trunk equipment
and separate signaling equipment unit. The M lead transmits
battery or ground signals to the signaling equipment, and
the E lead receives open or ground signals from the
signaling equipment.
E&M SIGNALING
An arrangement whereby signaling between a trunk circuit and
an associated signaling unit is effected over two leads
providing full-time, 2-way, 2-level supervision.
ENTERPRISE NUMBER
A unique telephone exchange number that permits the called
party to be automatically billed for incoming calls.
EQUAL ACCESS
Reprogramming of Local Exchange Company (LEC) switches to
allow other long distance companies besides AT&T to be the
"1+" primary long distance company for users of long
distance (by creating a new type of Feature Group access
circuit, FGD). Also provides "10-XXX" dialing for secondary
and casual calling, generates true hardware Answer
Supervision when calls are terminated over FGD circuits, and
provides ANI (Automatic Number Identification) on
originating calls.
EQUALIZATION
The procedure of compensating for fluctuation in circuit
amplitude, delay, or distortion.
ERLANG
A unit of traffic intensity. One Erlang is the intensity at
which one traffic path would be continuously occupied, e.g.
one call per hour.
ERLANG B TABLE
A widely used table derived from a mathematical formula
which allows the determination of the traffic capacity of a
given group of circuits.
EXCHANGE
A telephone switching center.
EXCHANGE NETWORK FACILITIES FOR INTERSTATE ACCESS (ENFIA)
AT&T's pricing arrangement for local loops offered to OCCs
for connecting the OCC's network to the local telephone
company's central office.
EXTENDED AREA SERVICE (EAS)
Adding expanded local calling areas to a caller's basic
local calling area for a (generally) small additional
monthly fee. The EAS local calls can be either free (after
a small additional monthly fee is paid) or at a cost of
reduced per call charges.
FACILITIES
Typically refers to transmission lines or circuits, or long
distance services. A caller's facilities are the circuits
available to make calls.
FACSIMILE
The transmission of pictures, maps or other documents via
communications circuits using a device which scans the
original document, transforms the image into coded signals
and reproduces the original document at a distant point.
FEATURE GROUP A
Line-side originating and terminating LATA access for which
an originating subscriber dials an assigned telephone number
that connects to a specific IC. The IC returns a tone to
signal the caller to input additional tone-generated digits
of the called number.
FEATURE GROUP B
Trunk-side originating and terminating LATA access for which
an originating subscriber dials a 950-WXXX number (where
W=0,1 and XXX is the Carrier Access Code), which is
translated to a specified XXX carrier trunk group. Optional
rotary dial service and ANI may be available.
FEATURE GROUP C
Trunk-side LATA access for AT&T, generally, on a direct
basis between each EO and an AT&T switching system.
FEATURE GROUP D
Also referred to as "Equal Access," Feature Group D is
trunk-side LATA access affording call supervision to an IC,
a uniform access code (10XXX), optional calling-party
identification, recording of access-charge billing details,
and presubscription to a customer-specified IC.
FEDERAL COMMUNICATIONS COMMISSION (FCC)
The government agency established by the Communications Act
of 1934 which regulates the interstate communications
industry.
FIBER OPTICS
High speed transmission using light to send images (in
telecommunications: voice or data) through a flexible
bundle of glass fibers.
FOUR WIRE CIRCUITS
Circuits which use two separate one-way transmission paths
of two wires each, as opposed to regular local lines which
usually only have two wires to carry conversations in both
directions. One set of wires carries conversation in one
direction, the other in the opposite direction.
FREQUENCY
The number of complete cycles per unit of time.
FREQUENCY DIVISION MULTIPLEXING (FDM) The division of an
available frequency range (bandwidth) into various
subdivisions, each having enough bandwidth to carry one
voice or data channel.
FREQUENCY RESPONSE
The reaction of frequencies to the circuit components.
FULL DUPLEX
A circuit which allows transmission of a message in both
directions at the same time.
Synonym: 4-wire.
FULL PERIOD
Relates to private line service, which is rented for the
exclusive use of a single customer for an entire month.
FX (FOREIGN EXCHANGE) SERVICE
A service which allows a customer to appear to have a local
presence in a distant part of town or, a different town
altogether, by connecting his/her phone directly to a local
business line in a part of town with a different exchange
than his/her local calling area over a leased private line,
or to a local telco in a distant town through long haul
private lines purchased from a long distance carrier.
GRADE OF SERVICE
The probability of a call being blocked by busy trunks,
expressed as a decimal fraction, and usually meaning the
busy-hour probability.
GROUP
12 circuits processed as a unit in a carrier system.
HALF DUPLEX
A circuit for transmitting or receiving signals in one
direction at a time.
HARDWIRE
To wire or cable directly between units of equipment.
HARMONIC
The full multiple of a base frequency.
HARMONIC DISTORTION
The ratio, expressed in decibels, of the power at the
fundamental frequency, to the power of a harmonic of that
fundamental.
HEAD END HOP OFF (HEHO)
A method of traffic engineering whereby calls are completed
by using long distance facilities directly off the switch
that serves that location.
HERTZ (Hz)
International standard unit of frequency. Replaces, and is
identical to, the order unit "Cycles-per-second."
HOMING
Returning to the starting position, as in a rotary stepping
switch.
HOOKSWITCH
The device on which the telephone receiver hangs or on which
a telephone handset hangs or rests when not in use. The
weight of the receiver or handset operates a switch which
opens the telephone circuit, leaving only the bell connected
to the line.
HOT-CUT
Virtually instantaneous replacement of one line with
another.
HYBRID
An electronic circuit which performs the wire conversions
necessary for the connection of a local loop with a long-
haul facility.
INTERCEPT
To stop a telephone call directed to an improper telephone
number, and redirect that call to an operator or a
recording.
INTERCONNECT
(1) The arrangement that permits the connection of
customer's telecommunications equipment to a communications
common carrier network. (2) The industry name for
manufacturers, excluding the Bell system, which provide
telephone equipment for the customer premises.
INTER-EXCHANGE MILEAGE (IXC)
The airline mileage between two cities.
Synonym: Long Haul Mileage.
INTEREXCHANGE PLANT
The facilities between the subscriber switching center and
another switching center.
INTERFACE
The junction or point of interconnection between two systems
or equipment having different characteristics.
INTERFERENCE
Any unwanted noise or crosstalk on a communications circuit
which acts to reduce the intelligibility of the desired
signal or speech.
INTER-MACHINE TRUNK (IMT)
A circuit which connects two automatic switching centers.
INTER-OFFICE TRUNK (IOT)
A direct trunk between local exchange offices.
INTERNATIONAL RECORD CARRIER (IRC)
Carriers providing international telecommunications
services, including voice, telex, and data communications.
INTERSTATE
Any connection made between two states.
INTRASTATE
Any connection made that remains within the boundaries of a
single state.
JITTER
Short term instability of the amplitude and/or phase of a
signal. Commonly called PHASE JITTER.
KEYSET
A telephone instrument having an appearance of two or more
telephone lines which can be accessed by depressing a button
(key) on the face of the set.
KEY SYSTEM
The equipment utilized to provide the features associated
with key sets, including keysets, multipair cable, key
service unit, distribution frames.
LEASED LINES
Any circuit or combination of circuits designated to be at
the exclusive disposal of a given subscriber.
Synonym: Private line; Full Period Line.
LEAST COST ROUTING (LCR)
A method of automatically selecting the least costly
facility for transmission of a call.
Synonym: Most Economical Route Selection (MERS); Automatic
Route Selection; Flexible Route Selection.
LEVEL
An expression of the relative signal strength at a point in
a communications circuit compared to a standard.
LOADING
A system for adding regularly spaced inductance units to a
circuit to improve its transmission characteristics.
LOCAL ACCESS AND TRANSPORT AREA (LATA)
A geographic area (called "exchange" or "exchange area" in
the MFJ) within each BOC's franchised area that has been
established by a BOC in accordance with the provisions of
the MFJ for the purpose of defining the territory within
which a BOC may offer its telecommunications services.
LOCAL AREA NETWORK (LAN)
Intraoffice communication system usually used to provide
data transmission in addition to voice transmission.
LOCAL EXCHANGE CARRIER (LEC)
A local telephone company, either one of the Bell Operating
Companies or one of the 1400+ independent local telephone
companies.
LOCAL LOOP
The local connection between the end user and the Class 5
central office.
LONG HAUL
Circuits spanning considerable distances.
LOOP BACK
A method of performing transmission tests on a circuit not
requiring the assistance of personnel at the distant end.
LOOP SIGNALING
Any of the three signaling methods which use the metallic
loop formed by the trunk conductors and the terminating
equipment bridges.
MAIN DISTRIBUTION FRAME (MDF)
The point where outside plant cables terminate and from
which they cross connect to terminal or central office line
equipment.
MAIN PBX
A PBX directly connected to a tandem switch via an access
trunk group.
MANUAL TIE LINE
A tie line which requires the assistance of an attendant at
both ends of the circuit in order to complete a call.
MASTER GROUP (MG)
240 circuits processed as a unit in a carrier system.
MESSAGE TELEPHONE SERVICE (MTS)
AT&T's tariffed pricing name for long distance telephone
calls.
MESSAGE UNIT (MU)
A local toll rate calling plan which is time and distance
sensitive.
MICROWAVE (M/W)
Radio transmission using very short lengths, corresponding
to a frequency of 1,000 megahertz or greater.
Synonym: Microwave Radio.
MICROWAVE RADIO
Synonym: Microwave.
MODEM
A device which modulates and demodulates signals on a
carrier frequency and allows the interface of digital
terminals with analog carrier systems.
MODIFIED FINAL JUDGEMENT (MFJ)
The agreement between the U.S. Department of Justice and
AT&T governing the breakup of the pre-Divestiture Bell
System into AT&T and 22 Bell Operating Companies and other
entities. On August 26, 1982, U.S. District Court Judge
Harold Greene accepted, with modifications, an AT&T/Justice
Department settlement terminating the government's 1974
antitrust suit against AT&T. Judge Greene's decree did away
with the provisions of the 1956 consent decree that had kept
AT&T out of competitive, unregulated ventures.
MODULATION
Alterations in the characteristics of carrier waves. Usually
impressed on the amplitude and/or the frequency.
MONITORING DEVICE
Records data on calls placed through a company's telephone
system: number called, length of calls, calling location.
MOST ECONOMICAL ROUTE SELECTION (MERS)
Synonym: Least Cost Routing.
MULTIPLEXING
The act of combining a number of individual message circuits
for transmission over a common path. Two methods are used:
(1) frequency division, and (2) time division.
NETWORK
A collection of switches connected to one another by
transmission facilities.
NETWORK NUMBERING EXCHANGE (NXX)
The three digit location code representing the central
office. "N" may be any number between "2" and "9" and "X"
may be any number.
NNX CODES
The 3-digit code used historically for local Exchange Codes.
"N" can be any number from 0 to 2, "X" can be any digit.
The current numbering plan allows for more variation in
assigning Exchange Codes, and under it Exchange Codes are
commonly referred to as "NXXs."
NODE
A major switching center of a network.
NON-BLOCKING
A switching network having a sufficient number of paths such
that a subscriber originating a call can always reach any
other idle subscriber without encountering a busy.
NUMBERING PLAN AREA (NPA)
A geographical division within which no two telephones will
have the same 7 digit number. "N" is any number between "2"
and "9"; "P" is always "1" or "0"; and "A" is any number
excluding "0". Commonly referred to as "area code."
NXX CODES
The current general configuration for Exchange Codes within
each Area Code. See also: "NNX Codes"
OFFERED TRAFFIC
The number of call attempts in any specified period of time.
OFF HOOK
The condition which results when a telephone is lifted from
its mounting, allowing the hookswitch to operate.
OFF-NETWORK ACCESS LINE (ONAL)
A local exchange (Feature Group access), Foreign Exchange,
or WATS line connecting both incoming and outgoing traffic
from a long distance company's network to the public
switched network. Generally a circuit leased by a long
distance carrier to be used by many customers not hooked
directly into the long distance carrier's network.
OFF NETWORK CALLING
Telephone calls through a private switching system and
transmission network which extend to the public telephone
system.
OFF PREMISES EXTENSION (OPX)
An extension telephone or keyset that is geographically
separated from its associated PBX.
ON HOOK
The condition which results when a telephone handset is
placed on its mounting, which causes the hook-switch to open
its contacts.
ON NETWORK CALLING
A term used to describe a call that originates and
terminates on a private network.
ORIGINATING OFFICE
The central office that serves the calling party.
OTHER COMMON CARRIER (OCC)
A long distance company other than AT&T having many of its
own long distance circuits, either owned or leased. Some
people use OCC to refer to all AT&T long distance
competitors, including resellers, but this is not
technically correct.
OUT-OF-BAND
Any frequency outside the band used for voice frequencies.
OUT-OF-BAND SIGNALING
Use of narrow band filters to place the voice signal on a
carrier channel below 3,400 CPS, reserving the 3,400 - 3,700
CPS band for supervisory signals.
OVERBUILD
Adding radio capacity to a telecommunications network.
OVERFLOW
Switching equipment which operates when the traffic load
exceeds the capacity of the regular equipment.
PAD
A non-adjustable resistance network used to insert
transmission loss into a circuit.
PHASE JITTER
SEE Jitter
POINT OF PRESENCE (POP)
A physical location within a LATA at which an IC establishes
itself for the purpose of obtaining LATA access and to which
the BOC provides access services.
POINT-TO-POINT
A communications circuit between two terminations which does
not connect with a public telephone system.
PORT
Entrance or access point to a computer, multiplexor device
or network where signals may be supplied, extracted or
observed.
POSTAL TELEPHONE AND TELEPGRAPH (PTT)
Foreign government agencies responsible for regulating
communications.
PRIMARY AREA
A customer's local telphone calling area.
PRIMARY INTEREXCHANGE CARRIER (PIC)
The IC designated by a customer to provide inter-LATA
service automatically without requiring the customer to dial
an access code for that carrier.
PRIMARY ROUTING POINT
The switch designated as the control point for a longhaul
telephone call.
PRIVATE BRANCH EXCHANGE (PBX)
A private phone system (switch) used by medium and large
companies which is connected to the public telephone network
(local telco) and performs a variety of in-house routing and
switching. User usually dial "9" to get outside system to
the local lines.
PRIVATE LINE (PL)
A full-time leased line directly connecting two points, used
soley by purchaser. The most common form is a tie line
connecting two pieces of a user's own phone equipment - flat
rate billing, not usage sensitive.
PRIVATE USE NETWORK
Two or more private line channels contracted for by a
customer and restricted for use by that customer only.
PUBLIC SWITCHED NETWORK (PSN)
The pre-Divestiture nationwide network maintained by AT&T
and the independent telephone companies which provides
nationwide, unrestricted telephone service.
PUBLIC UTILITY COMMISION (PUC)/PUBLIC SERVICE COMMISSION
(PSC)
The state commissions regulating intrastate communications.
PULSE CODE MODULATION (PCM)
The form of modulation in which the information signals are
sampled at regular intervals and a series of pulses in coded
form are transmitted representing the amplitude of the
information signal at that time.
PULSE-LINK REPEATER
Connects one E&M signaling circuit directly to another.
PULSE MODULATION The modulation of a series of pulses which
represents information-bearing signals. Typical methods
involve modifying the amplitude (PAM), width or duration
(PWM) or position (PPM). Pulse Code Modulation (PCM) is the
most common modulation technique involved in telephone work.
PUSH BUTTON DIALING
Synonym: Dual Tone Multi-Frequency.
QUEUE
A temporary delay in providing service caused by the
inability of the system provided to handle the number of
messages or calls attempted.
RADIO COMMON CARRIER (RCC)
A communications common carrier that provides radio paging
and mobile telephone services to the public.
RATE CENTER
A specified geographic location used by the telephone
company to determine interchange mileage for rate
determination purposes.
REDUNDANCY
Duplicate equipment that is provided to minimize the effect
of failures or equipment breakdowns.
REGENERATION
The process of receiving distorted signal pulses and from
them recreating new pulses at the correct repetition rate,
pulse amplitude, and pulse width.
RE-HOMING
A major network change which involves moving customer
services from one switching center to another and
establishing the necessary trunking facilities to do so.
REMOTE ACCESS
The ability of transmission points to gain access to a
computer which is at a different location.
REPEATER
An electronic device used to amplify signals which have
become too weak.
REPEATING COIL
The telephone industry's term for a voice-frequency
transformer.
RESELLER
A long distance company that purchases large amounts of
transmission capacity or calls from other carriers and
resells it to smaller users.
RESTORATION
The re-establishment of service by rerouting, substitution
of component parts, or as otherwise determined.
RETARD COIL
A coil having a large inductance which retards sudden
changes of the current flowing through its winding.
RINGBACK TONE
Synonym: Audible Ringing Tone.
RINGDOWN
A circuit or method of signaling where the incoming signal
is actuated by alternating current over the circuit.
ROUTE DIVERSITY
Two (or more) private line channels (circuits) furnished
partially or entirely over two physically separate routes.
Serves to prevent total loss of service if one cable gets
cut or goes out.
ROUTE OPTIMIZATION
Synonym: Least Cost Routing.
ROTARY HUNT
An arrangement which allows calls placed to seek out an idle
circuit in a prearranged multi-circuit group and find the
next open line to establish a through circuit.
SATELLITE RELAY
An active or passive repeater in geosynchronous orbit around
the Earth which amplifies the signal it receives before
transmitting it back to earth.
SELECTIVE CALLING
The ability of a transmitting station to specify by the use
of assigned codes which of several stations is to receive a
message.
SERVICE AND EQUIPMENT RECORD
A list of equipment billed to customer by type, quantity,
monthly charge, location and billing dates.
SF SIGNALING (SINGLE-FREQUENCY)
A signaling system which uses a 2,600 Hz in-band signal on
the voice path. The tone is on in the idle condition,
pulsed for dialing, and off when the circuit is in use.
SHORT HAUL
Circuits designed for use over distances of 10-200 miles.
SIGNALING
The process of transferring information between two parts of
a telephone network to control the establishment of
communications between long distance carrier terminal
points, and customer equipment required for voice grade
dedicated circuits.
SIGNALING CONVERTER
A device with input and output signals that contain the same
information but employ different electrical systems for
transmitting that information. Used at the terminal of a
trunk to convert the equipment signals to the system used on
the trunk. Examples are: (1) ring down to SF, (2) E&M to
SF.
SIGNALING, IN-BAND
A type of signaling using an AC signal (usually 2,600 Hz)
within the normal voice band. This signal can be
transmitted from end to end of a long voice circuit without
an intermediate signaling equipment. Since the signaling is
audible, the signaling equipment must be arranged for "tone
on when idle" operation.
SIGNAL TO NOISE RATIO
Ratio of the signal power to the noise power in a specified
bandwidth, usually expressed in db.
SIMPLEX (SX) SIGNALING A signaling path over a dry talking
circuit which uses the two sides of the circuit in parallel,
derived by connecting the midpoints of repeating coils or
retardation coils which are across the circuit.
SINGLE SIDEBAND RADIO (SSB)
A form of amplitude modulation of a radio signal in which
only one of the two sidebands is transmitted. Either of the
two sidebands may be transmitted, and the carrier may be
transmitted, reduced or suppressed.
SINGING
A continued whistle or howl in an amplified telephone
circuit. It occurs when the sum of the repeater gains
exceeds the sum of the circuit losses.
SOFTWARE DEFINED NETWORK (SDN)
A switched long distance service for very large users with
multiple locations. Instead of putting together their own
network, large users can get special usage rates for calls
made on regular long distance company switched long distance
services.
Synonym: Virtual Private Network.
SPECIAL GRADE NETWORK TRUNK
A trunk specially conditioned by providing amplitude and
delay equilization for the purpose of handling special
services such as medium-speed data (600 to 2400 BPS).
SPECIALIZED COMMON CARRIER (SCC)
Synonym: Other Common Carrier.
SPEED NUMBER
A one, three, or four digit number that replaces a seven or
ten digit telephone number. These numbers are programmed
into the switch in the carrier's office or in a PBX.
STATION
Any customer location on a network capable of sending or
receiving messages or calls.
STATION MESSAGE DETAIL RECORDING (SMDR)
A computer generated report showing internal usage on a
telephone system. Usually including extension number, trunk
number used, phone number dialed, time of call, duration and
operator involvement.
STORE-AND-FORWARD
A technique in which a message is received from the
originator and held in storage until a circuit to the
addressee becomes available.
STORED PROGRAM CONTROL (SPC)
A system whereby the instructions are placed in the memory
of a commoncontrolled switching unit and to which it refers
while processing a call for instructions regarding class
marks, code conversions, routing, as well as for trouble
analysis.
SUPERGROUP (SG)
60 circuits processed as a unit in a carrier system.
SUPERMASTERGROUP (SMG)
600 circuits processed as a unit in a carrier system.
SUPERVISION
Synonym: Answer Supervision.
SUPERVISORY SIGNALS
A signal, such as "on-hook" or "off-hook," which indicates
whether a circuit or line is in use.
SWITCH
Equipment used to interconnect lines and trunks.
SWITCHED ACCESS
Connection between caller's phone system and switch of
chosen long distance carrier when a regular long distance
call using regular local lines is made. Also the connection
between the switch of caller's long distance carrier in the
distant city and the phone being called.
SWITCH HOOK
Synonym: Hookswitch.
SWITCHING
The operations involved in interconnecting circuits in order
to establish communications.
SWITCHING CENTER
A location at which telephone traffic, either local or toll,
is switched or connected from one circuit or line to
another.
SWITCHING OFFICE
A telephone company office which contains a switch.
T-1
24 voice channels digitized at 64,000 bps, combined into a
single 1.544 Mbps digital stream (8,000 bps signaling), and
carried over two pairs of regular copper telephone wires.
Used primarily by telephone companies until 1983. Now used
for dedicated local access to long distance facilities,
long-haul private lines, and for regular local service.
Today, most any 1.544 Mbps digital stream is called T-1,
regardless of its makeup or what the transmission medium is.
T-CARRIER
A time-division, pulse-code modulation, voice carrier used
on exchange cable to provide short-haul trunks.
TAIL END HOP OFF (TEHO)
In a private network, a call which is carried over flat rate
facilities (Intermachine Trunks or IMT) to the closest
switch node to the destination of the call, and then
connected into the public network as a local call.
TANDEM
A switching arrangement in which the trunk from the calling
office is connected to a trunk to the called office through
an intermediate point.
TANDEM SWITCHING SYSTEM
Synonym: Tandem Tie Trunk Network.
TANDEM TIE TRUNK NETWORK (TTTN)
A serving arrangement which permits sequential connection of
tie trunks between PBX/CENTREX locations by utilizing tandem
operation.
TANDEM TRUNKING
Trunks which connect two or more switches together.
TARIFF
The published rates, regulations, and descriptions governing
the provisions of communications service.
TELCO
Local telephone company.
TELECOMMUNICATIONS
The transmission of voice and/or data through a medium by
means of electrical impulses and includes all aspects of
transmitting information.
TELEGRAPH
A system employing the interruption of, or change in, the
polarity of DC current signaling to convey coded
information.
TELEPHONE
A device which converts acoustical (sound) energy into
electrical energy for transmission to a distant point.
TELETYPEWRITER
A machine used to transmit and/or receive communications on
printed page and/or tape.
TERMINAL
A point at which information can enter or leave a
communications network.
TERMINAL EQUIPMENT
Devices, apparatus and their associated interfaces used to
forward information to a local customer or distant terminal.
TERMINATION
(1) An item that is connected to the terminal of a circuit
or equipment. (2) An impedance connected to the end of a
circuit being tested. (3) The points on a switching network
to which a trunk or line may be attached.
TIE-LINE
A private leased line linking two phones or phone systems
directly. Can ring distant phone automatically when
telephone is lifted from its mounting, or when a short code
is dialed.
TIME DIVISION MULTIPLEXING (TDM)
Equipment which enables the transmitting of a number of
signals over a single common path by transmitting them
sequentially at different instants of time.
TOLL CALL
Any call to a point outside the local service area.
TOLL CENTER
A central office where operators (human or mechanical) are
present to assist in completing incoming toll calls.
TOLL OFFICE
A center for the switching of toll calls.
TOLL PLANT
The facilities that connect toll offices throughout the
country.
TOLL RESTRICTION
A restriction in outgoing trunks which counts the first
three digits dialed and diverts calls to forbidden codes
either to a busy tone, to the operator, or to a recorded
announcement.
TOUCH-TONE ADAPTOR
A device that can be connected to a rotary dial telephone to
allow for DTMF signaling.
TRAFFIC
Calls being sent and received over a communications network.
TRAFFIC MEASUREMENT AND RECORDING SYSTEMS (TMRS)
A computer generated report showing usage information of
telephone systems. Usually this includes trunk utilization,
outages, queueing time, and the need for additional common
equipment.
TRAFFIC SERVICE POSITION SYSTEM (TSPS)
A toll switchboard position configured as a push button
console.
TRANSMISSION
The electrical transfer of a signal, message or other form
of data from one location to another without unacceptable
loss of information content due to attenuation, distortion,
or noise.
TRANSMISSION LEVEL
The level of power of a signal, normally 1,000 Hz, which
should be measured at a particular reference point.
TRANSMISSION SPEED
Number of pulses or bits transmitted in a given period of
time, usually expressed as Bits Per Second (BPS) or Words
Per Minute (WPM).
TRUNK
A telephone circuit or path between two switches, at least
one of which is usually a telephone company Central Office
or switching center. Regular local CO circuits are called
PBX trunks, because there is a switch at both ends of the
circuit.
TRUNK GROUP
An arrangement of communications channels into an identical
group.
TRUNK TYPE (TT)
Trunks that use the same type of equipment going to the same
terminating location.
TRUNK UTILIZATION REPORT (TUR)
A computer printout detailing the traffic use of a trunk.
TWO-WIRE CIRCUIT
(1) A channel for transmitting data in one direction at a
time. (2) A short distance channel using a single
send/receive pathway, usually 2 copper wires, connecting a
telephone to a switch.
TELETYPEWRITER EXCHANGE SERVICE (TWX)
A service whereby a customer's leased teletypewriter is
connected to a "TWX" switchboard and from there connected
over regular toll circuits to a teletypewriter of any U.S.
customer who subscribes to a similar service.
UNIFORM CALL DISTRIBUTOR (UCD)
A device located at the telephone office or in a PABX which
distributes incoming calls evenly among individuals.
UNIFORM SERVICE ORDER CODE (USOC)
The information in coded form for billing purposes by the
local telephone company pertaining to information on service
orders and service equipment records.
VALUE-ADDED NETWORK SERVICE (VANS)
A data transmission network which routes messages according
to available paths, assures that the message will be
received as it was sent, provides for user security, high
speed transmission and conferencing among terminals.
VIA NET LOSS (VNL)
The lowest loss in dB at which a trunk facility can be
operated considering limitations of echo, crosstalk, noise
and singing.
VOICE CONNECTING ARRANGEMENT
An interface arrangement provided by the telephone company
to accomodate the connections of non-carrier provided voice
terminal equipment to the public switched telephone network.
VOICE FREQUENCY (VF)
Any of the frequencies in the band 300-3,400 Hz which must
be transmitted to reproduce the voice with reasonable
fidelity.
VOICE GRADE
An access line suitable for voice, low-speed data,
facsimile, or telegraph service. Generally, it has a
frequency range of about 300-3000 Hz.
VOICE GRADE FACILITY (VGF)
A circuit designed to DDD network standards which is
suitable for voice, low-speed data, facsimile, or telegraph
service.
WIDE AREA TELECOMMUNICATIONS SERVICE (WATS)
WATS permits customers to make (OUTWATS) or receive
(INWATS)
long-distance calls and to have them billed on a bulk rather
than individual call basis. The service is provided within
selected service areas, or bands, by means of special
private access lines connected to the pubic telephone
network via WATS-equipped central offices. A single access
line permits inward or outward service, but not both.
WIDEBAND
A term applied to facilities or circuits where bandwidths
are greater than that required for one voice channel.
WIRE CENTER
The physical structure that houses one or more central
office switching systems.
"0" or "0-"
Zero minus dialing. Allows a caller to dial zero and
nothing else to get the Operator.
"0+"
Zero plus dialing. An operator assisted long distance call
which is charged to the calling party.
"00+" or "00-"
Double zero dialing. Allows a caller to get an AT&T
Operator in areas in which dialing only one zero would
connect the caller with the local Operator because AT&T has
given Operators back to the local telephone company.
"1+" DIALING
The capability to dial "1" plus the long distance number for
calls withing the North American Numbering Plan area.
Intra-LATA calls are carried by the local telephone company.
Inter-LATA calls are carried by the caller's primary
carrier, or by AT&T if equal access has not come to the
caller's area yet.
"10-XXX" DIALING
The ability to send calls over a carrier other than a
caller's primary carrier by dialing "10-XXX" then "1+" the
long distance number, where "XXX" is the 3-digit Carrier
Code of the alternative long distance company (also called a
secondary carrier). Available only to Equal Access
customers.
800 SERVICE
The ability of a caller to dial a long distance telephone
number without incurring a charge for the call, which is
paid for by the party offering the 800 number.
Synonym: Inward WATS service.
900 SERVICE
Allows callers to receive information from the service
provider via a recorded audio message, which can range from
60 seconds to a continuous live hookup, by calling a 900
number. This service can also be used to enable callers to
vote or "make a choice" by dialing one of two 900 numbers.
900 calls are typically billed to the caller at $.50 for the
first minute of any call and $.35 for each additional
minute.
976 NUMBERS
Service which allows callers to listen to recorded messages
such as horoscopes, 'adult' dialogue, stock market or sports
reports by calling 976-xxxx. The local telephone company
charges callers a fee which is split between the local
telephone company and the service provider.
