SEAGATE TECHNOLOGY, INC.
Customer Technical Support FAX Network +1 408 438-8137
Customer Technical Support Bulletin Boards (300-9600, 8-N-1)
��������������������������������������������������������������������Ŀ
� United States +1 408 438-8771 � United Kingdom +44 628 478011 �
��������������������������������������������������������������������Ĵ
� Germany +49 89 140-9331 � Singapore +65 227-2217 �
���������������������������������������������������������������������
(C)opyright 1991
ST-41600N (97501-16G) Elite-1 FH SCSI-2
�� This T-RES only on Differential model
� (see below for T-RES descriptions)
Spindle Sync � � �� Terminator Power Source (see below)�Ŀ
�4��1�Ŀ ���*���1 4o�o3 �������1 �
p�o oo A �ij����� 2o o1 ��ij���� �
o o o o o n�o oo B �Terminator DIPS� Power o o o o �
o o o o o ��������������������������������� �12�G�G�5Ŀ o o o o �
������������P�W�A��͵::::::::::::::::::::::::1��͵ 0 0 0 0 ����������� �
4 2 1 � � �������������������������; \���������/ � � � � �
����� � � SCSI Cable Connector � � � � �
� � � � � � � �
� � ��� Master off/Slave on - Spindle Sync � � � � �
� ����� Write Protect option enable � � � � �
��������� SCSI ID � � � � �
Spinup Delay (10 secs * ID) �� � � � �
Motor Start option enable ���� � � �
Parity check DISable ������ � �
Sweep Cycle enable �������� �
�
���������������������������������� �
� Terminator Power Source Options ������������������������������������������
���������������������������������������������������������������������Ŀ
� 2 & 4 � Initiator supplies power over the SCSI Bus for terminators. �
� Drive supplies no terminator power. �
� 1 & 2 � Drive supplies power for its own terminator resistor-paks �
� but not to SCSI Bus. This is the factory setting. �
� 1 & 3 �
� AND � Drive supplies power for external terminator at end of the �
� 2 & 4 daisy chain. Terminator resistor-paks must be removed. �
� This option is recommended only for last drive on daisy �
� chain. �
������������������������������������������������������������������������
T-RES descriptions: ST41600N 1 DIP
ST41601N 2 SIPs
ST41600ND 2 DIPs
ST41601ND 2 DIPs
ST-41600N
Elite-1 FH
UNFORMATTED CAPACITY ____ ________________1,600,930,800
FORMATTED CAPACITY (xx SECTORS) ____ _____1,370,545,152 **
AVERAGE SECTORS PER TRACK (with spares)___74.945
ACTUATOR TYPE ____________________________ROTARY VOICE COIL
TRACKS/USER ______________________________35,717/35,666
CYLINDERS/USER ___________________________2,101/2,098
HEADS ____________________________________17
DISCS ____________________________________10
MEDIA TYPE _______________________________THIN FILM
HEAD TYPE ________________________________THIN FILM
RECORDING METHOD _________________________ZBR RLL (2,7)
INTERNAL TRANSFER RATE (mbits/sec) _______26 to 36
EXTERNAL TRANSFER RATE (mbytes/sec) ______5
SPINDLE SPEED (RPM) ______________________5,400
AVERAGE LATENCY (mSEC) ___________________5.56
COMMAND OVERHEAD (msec) __________________<0.5
BUFFER ___________________________________256 Kbyte
Read Look-Ahead, Adaptive, Multi-Segmented
Cache
INTERFACE ________________________________SCSI-2
BYTES PER TRACK __________________________36,120 to 50,400
SECTORS PER DRIVE ________________________2,676,846
TPI (TRACKS PER INCH) ____________________
BPI (BITS PER INCH) ______________________
AREAL DENSITY ____________________________
AVERAGE ACCESS (ms) ______________________11.5
SINGLE TRACK SEEK (ms) ___________________1.7
MAX FULL SEEK (ms) _______________________22.5
MTBF (power-on hours) Class A Room _______250,000
MTBF (power-on hours) Office _____________150,000
POWER DISSIPATION (watts/BTU) ____________
POWER REQUIREMENTS: Single-ended/Differential
+12V START-UP (amps) _2.2/3.2
+12V TYPICAL (amps) __1.8/1.8
+5V TYPICAL (amps) ___2.1/2.4
TYPICAL (watts) ______32.1/33.6
MAXIMUM (watts) ______39.1/41.6
LANDING ZONE (cyl) _______________________AUTO PARK
USER MANUAL PART NUMBER __________________83327460
REFERENCE MANUAL PART NUMBER _____________83327470
IBM AT DRIVE TYPE ________________________0 or NONE
OTHER ____________________________________
ZBR = Zone Bit Recording = Variable sectors per track
** Already low-level formatted at the factory with six spare sectors
per cylinder, one spare cylinders/unit, one system cylinder/unit, and
one diagnostic cylinder/unit.
