SEAGATE TECHNOLOGY, INC.
Customer Technical Support FAX Network +1 408 438-8137
Customer Technical Support Bulletin Boards (300-9600, 8-N-1)
��������������������������������������������������������������������Ŀ
� United States +1 408 438-8771 � United Kingdom +44 628 478011 �
��������������������������������������������������������������������Ĵ
� Germany +49 89 140-9331 � Singapore +65 227-2217 �
���������������������������������������������������������������������
(C)opyright 1993
ST-410800W Elite 9 Fast SCSI-2 Wide
�� Terminator Power Source (see below)�Ŀ
4o�o3 �
J4A 2o o1 J4B �
o o o o o o A R o o Power o o o o �
o o o o o o g F o o ___________________ �12�G�G�5Ŀ o o o o �
�������������������������( �����������������1)����͵ 0 0 0 0 ����������� �
8 4 2 1 � � ��� � � \�����������ij����/ \���������/ � � � � �
������� � � � � � SCSI Cable Connector 68-pin � � � � �
� � � � � � � � � � �
� � � � � ��� Spindle Synch Cable Connector � � � � �
� � � � � (top pin: SSREF, bottom: ground) � � � � �
� � � � ������ Terminator Enable � � � � �
� � � ���������� LED Connection (g: ground pin) � � � � �
� � � Activity (A-G) � � � � �
� � � Ready (R-G) � � � � �
� � � Fault (F-G) � � � � �
� � �� Reserved � � � � �
� ���� Write Protect Enable Spinup Delay �� � � � �
��������� SCSI ID (10 secs * ID) � � � �
Motor Start option enable ���� � � �
Parity check DISable ������ � �
Reserved �������� �
���������������������������������� �
� Terminator Power Source Options ������������������������������������������
���������������������������������������������������������������������Ŀ
� 2 & 4 � Initiator supplies power over the SCSI Bus for terminators. �
� Drive supplies no terminator power. �
� 1 & 2 � Drive supplies power for its own terminator resistor-paks �
� but not to SCSI Bus. This is the factory setting. �
� 1 & 3 �
� AND � Drive supplies power for external terminator at end of the �
� 2 & 4 daisy chain. Terminator resistor-paks must be removed. �
� This option is recommended only for last drive on daisy �
� chain. �
������������������������������������������������������������������������
ST410800WD drives are shipped without terminators and have
empty terminator sockets on the PCB. You must provide
termination resistors for these drives.
ST-410800W
Elite 9
UNFORMATTED CAPACITY _____________________10,800
FORMATTED CAPACITY (512 byte blk) ________9,090
AVERAGE SECTORS PER TRACK ________________133 (rounded down)
ACTUATOR TYPE ____________________________ROTARY VOICE COIL
TRACKS ___________________________________132,975
CYLINDERS ________________________________4925
HEADS ____________________________________27
DISCS (5.25 in) __________________________14
MEDIA TYPE _______________________________THIN FILM
HEAD TYPE ________________________________THIN FILM
RECORDING METHOD _________________________ZBR RLL (1,7)
INTERNAL TRANSFER RATE (mbits/sec) _______45-66
INTERNAL TRANSFER RATE AVG (mbyte/sec) ___7.2
EXTERNAL TRANSFER RATE (mbyte/sec) _______20 (burst)
SPINDLE SPEED (RPM) ______________________5,400
AVERAGE LATENCY (mSEC) ___________________5.55
COMMAND OVERHEAD (mSEC) __________________<0.5
BUFFER ___________________________________1024 Kbyte
Read Look-Ahead, Adaptive, Multi-Segmented
Cache
INTERFACE ________________________________SCSI-2 FAST
BYTES PER TRACK __________________________63,000-91,000
SECTORS PER DRIVE ________________________17,845,731
BYTES PER CYLINDER _______________________1,058,400 to 1,587,600
TPI (TRACKS PER INCH) ____________________3,979
BPI (BITS PER INCH) ______________________
AVERAGE ACCESS (ms) read/write ___________11/12
SINGLE TRACK SEEK (ms) read/write ________0.9/1.7
MAX FULL SEEK (ms) read/write ____________23/24
MTBF (power-on hours) Class A Room _______NA
MTBF (power-on hours) Office _____________500,000
POWER DISSIPATION (watts) ________________
POWER REQUIREMENTS: Single-ended/Differential
+12V START-UP (amps) _3.98/4.60
+12V TYPICAL (amps) __1.90/1.88
+5V START-UP (amps) __2.37/3.48
+5V TYPICAL (amps) ___1.96/2.77
TYPICAL ( watts seek/read)_32.60/36.41
IDLE (watts) ______________28.34/31.81
USER MANUAL PART NUMBER __________________
OTHER ____________________________________
Synchronized Spindles, Sweep Cycle Capability
** Already low-level formatted at the factory with nine spare sectors
per cylinder, one spare cylinders/unit, one system cylinder/unit, and
one diagnostic cylinder/unit.