ST-3390N
Left View o o o1
(TOP) o o o �
Front....���������������������������͵ I/O connector
� � � �;
SCSI Address ID 1 �� � �
ID 2 ���� �
ID 4 ������
ST-3390N
Right View
o o4 o o o6 (TOP)
� 1o�o 1o�o o
DC Power ������������ � ��������������������������������
�; � �
� ������
� Active/Passive Termination
���� �������
Terminator Power �������������������������������Ŀ
����� � Active: Pins 1 & 2 shorted �
� � only (+2.85V to �
� � 110 �) for FAST �
� � SCSI; �
� �Passive: Pins 2 & 4 shorted �
� � AND pins 5 & 6 shorted �
� � (+5V and GND to �
� � 220/330 �) for �
� � standard SCSI. �
� ����������������������������������
�
���������������������������������������������������������������������Ŀ
�Terminator Power: From SCSI Connector ���������������� Pins 1 & 2 �
� From Power Connector ��������������� Pins 1 & 3 �
� To SCSI Connector Only ������������� Pins 3 & 4 �
� From Power Connector and ����������� Pins 1 & 2 AND �
� to SCSI Bus --------------------------- 3 & 4 �
� Terminating Resistors not Installed � Pins 2 & 4 �
������������������������������������������������������������������������
ST-3390N
Front View
������������������� SCSI ID's (none for ID0)
� not used if ID set on side jumpers
� ��������������� Ext. Spindle Clock Synch
� � pin-5 is Clock Ground
� � ������������� Remote LED
(TOP) ��Ŀ � � ������� Reserved
4 2 1 � � ������Ŀ
o o o o o-o o o o o
1o o o o o+o o o o o o o o o+
��������������������1o o o o-����������������
� � � �
(BOTTOM) � � � ��� Remote LED
� � ����� Ext. Spindle Clock Synch
� � pin-5 is Clock Ground
� ������� Remote Start Enable
��������� Parity Enable
ST-3390N
UNFORMATTED CAPACITY _____________________
FORMATTED CAPACITY (xx SECTORS) __________344.3
AVERAGE SECTORS PER TRACK ________________83 rounded down
ACTUATOR TYPE ____________________________ROTARY VOICE COIL
TRACKS ___________________________________8,028
CYLINDERS ________________________________2,676 (user)
HEADS ____________________________________3
DISCS (3.5 in) ___________________________2
MEDIA TYPE _______________________________THIN FILM
HEAD TYPE ________________________________THIN FILM
RECORDING METHOD _________________________ZBR RLL (1,7)
INTERNAL TRANSFER RATE (mbits/sec) _______21.6 to 36.3
EXTERNAL TRANSFER RATE (mbyte/sec) _______4 Async
EXTERNAL TRANSFER RATE (mbyte/sec) _______10 Sync
SPINDLE SPEED (RPM) ______________________4,500
AVERAGE LATENCY (mSEC) ___________________6.67
BUFFER ___________________________________256 Kbyte SeaCache
Multisegmented, read look-ahead
INTERFACE ________________________________SCSI-2 Fast
BYTES PER TRACK __________________________42,888 avg.
SECTORS PER DRIVE ________________________672,480
TPI (TRACKS PER INCH) ____________________3,000
BPI (BITS PER INCH) ______________________52,602
AVERAGE ACCESS (ms) ______________________12
SINGLE TRACK SEEK (ms) ___________________<4
MAX FULL SEEK (ms) _______________________30
MTBF (power-on hours) Office _____________250,000
POWER REQUIREMENTS: +12V START-UP (amps) _1.9
POWER MANAGEMENT (Watts):
ACTIVE _______________5.75
IDLE _________________3.0
WRITE PRECOMP (cyl) ______________________N/A
REDUCED WRITE CURRENT (cyl) ______________N/A
LANDING ZONE (cyl) _______________________AUTO
IBM AT DRIVE TYPE ________________________0
Formatted at the factory with 2 alternate cylinders. Total physical
cylinders equal 2678.
Note: If FAST SCSI transfer rates are used, then the active
termination options must be used. If the transfer rates are 5.0
MBytes/sec and below, either method of termination can be used.
Although active and passive terminated devices can be installed on the
same bus, both ends of the cable should be terminated in the same
manner, either both active or both passive.
Note: If your application requires no terminators, remove the
terminators from the circuit board. Merely removing the terminator
power source selection jumper does not disconnect the terminator
resistors from the circuit.
ZBR = Zone Bit Recording = Variable sectors per track
Seagate reserves the right to change, without notice, product
offerings or specifications. (08/08/94)
