/*      $NetBSD: hilreg.h,v 1.1 2011/02/06 18:26:54 tsutsui Exp $       */
/*      $OpenBSD: hilreg.h,v 1.6 2006/08/10 23:43:45 miod Exp $ */
/*      NetBSD: hilreg.h,v 1.6 1997/02/02 09:39:21 thorpej Exp  */

/*
* Copyright (c) 1988 University of Utah.
* Copyright (c) 1990, 1993
*      The Regents of the University of California.  All rights reserved.
*
* This code is derived from software contributed to Berkeley by
* the Systems Programming Group of the University of Utah Computer
* Science Department.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
*    notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
*    notice, this list of conditions and the following disclaimer in the
*    documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors
*    may be used to endorse or promote products derived from this software
*    without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED.  IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* from: Utah $Hdr: hilreg.h 1.10 92/01/21$
*
*      @(#)hilreg.h    8.1 (Berkeley) 6/10/93
*/

#include <machine/hil_machdep.h>

#define HIL_BUSY                0x02
#define HIL_DATA_RDY            0x01

/* HIL status bits */
#define HIL_POLLDATA    0x10            /* HIL poll data follows */
#define HIL_COMMAND     0x08            /* Start of original command */
#define HIL_ERROR       0x80            /* HIL error */

#define HIL_RECONFIG    0x80            /* HIL has reconfigured */
#define HIL_UNPLUGGED   0x84            /* HIL cable unplugged */

#define HIL_SSHIFT      4               /* Bits to shift status over */
#define HIL_SMASK       0x0f            /* Service request status mask */
#define HIL_DEVMASK     0x07

/* HIL status types */
#define HIL_68K         0x04            /* Data from the 68k is ready */
#define HIL_STATUS      0x05            /* HIL status in data register */
#define HIL_DATA        0x06            /* HIL data in data register */
#define HIL_CTRLSHIFT   0x08            /* key + CTRL + SHIFT */
#define HIL_CTRL        0x09            /* key + CTRL */
#define HIL_SHIFT       0x0a            /* key + SHIFT */
#define HIL_KEY         0x0b            /* key only */

/* HIL commands */
#define HIL_IDENTIFY    0x03            /* Get device information */
#define HIL_READTIME    0x13            /* Read real time register */
#define HIL_RNAME       0x30            /* Report name */
#define HIL_RSTATUS     0x31            /* Report status */
#define HIL_DESCRIBE    0x32            /* Extended describe */
#define HIL_SECURITY    0x33            /* Read security bits */
#define HIL_DKR         0x3d            /* Disable auto repeat */
#define HIL_ER1         0x3e            /* Enable auto repeat 1/30 */
#define HIL_ER2         0x3f            /* Enable auto repeat 1/60 */
#define HIL_PROMPT1     0x40            /* Prompt #1 */
#define HIL_PROMPT2     0x41            /* Prompt #2 */
#define HIL_PROMPT3     0x42            /* Prompt #3 */
#define HIL_PROMPT4     0x43            /* Prompt #4 */
#define HIL_PROMPT5     0x44            /* Prompt #5 */
#define HIL_PROMPT6     0x45            /* Prompt #6 */
#define HIL_PROMPT7     0x46            /* Prompt #7 */
#define HIL_PROMPT      0x47            /* Prompt */
#define HIL_ACK1        0x48            /* Acknowledge #1 */
#define HIL_ACK2        0x49            /* Acknowledge #2 */
#define HIL_ACK3        0x4a            /* Acknowledge #3 */
#define HIL_ACK4        0x4b            /* Acknowledge #4 */
#define HIL_ACK5        0x4c            /* Acknowledge #5 */
#define HIL_ACK6        0x4d            /* Acknowledge #6 */
#define HIL_ACK7        0x4e            /* Acknowledge #7 */
#define HIL_ACK         0x4f            /* Acknowledge */
#define HIL_INTON       0x5c            /* Turn on interrupts. */
#define HIL_INTOFF      0x5d            /* Turn off interrupts. */
#define HIL_SETARD      0xa0            /* Set auto-repeat delay */
#define HIL_SETARR      0xa2            /* Set auto-repeat rate */
#define HIL_SETTONE     0xa3            /* Set tone generator */
#define HIL_CNMT        0xb2            /* Clear nmi */
#define HIL_TRIGGER     0xc5            /* Trigger command */
#define HIL_STARTCMD    0xe0            /* Start loop command */
#define HIL_TIMEOUT     0xfe            /* Timeout */

/* Read/write various registers on the 8042. */
#define HIL_READBUSY            0x02    /* internal "busy" register */
#define HIL_READKBDLANG         0x12    /* read keyboard language code */
#define HIL_WRITEKBDSADR        0xe9
#define HIL_WRITELPSTAT         0xea
#define HIL_WRITELPCTRL         0xeb
#define HIL_READKBDSADR         0xf9
#define HIL_READLPSTAT          0xfa
#define HIL_READLPCTRL          0xfb

/* BUSY bits */
#define BSY_LOOPBUSY    0x04

/* LPCTRL bits */
#define LPC_AUTOPOLL    0x01    /* enable auto-polling */
#define LPC_NOERROR     0x02    /* don't report errors */
#define LPC_NORECONF    0x04    /* don't report reconfigure */
#define LPC_KBDCOOK     0x10    /* cook all keyboards */
#define LPC_RECONF      0x80    /* reconfigure the loop */

/* LPSTAT bits */
#define LPS_DEVMASK     0x07    /* number of loop devices */
#define LPS_CONFGOOD    0x08    /* reconfiguration worked */
#define LPS_CONFFAIL    0x80    /* reconfiguration failed */

/* HIL packet headers */
#define HIL_MOUSEDATA   0x02
#define HIL_KBDDATA     0x70

#define HIL_MOUSEMOTION 0x02    /* mouse movement event */
#define HIL_TABLET      0x02    /* tablet motion event */
#define HIL_KNOBBOX     0x03    /* knob box motion data */
#define HIL_KBDBUTTON   0x40    /* keyboard button event */
#define HIL_MOUSEBUTTON 0x40    /* mouse button event */
#define HIL_BUTTONBOX   0x60    /* button box event */

/* ID module defines */
#define HILSCBIT        0x04

/* For setting auto repeat on the keyboard */
#define ar_format(x)    ~((x - 10) / 10)
#define KBD_ARD         400     /* initial delay in msec (10 - 2560) */
#define KBD_ARR         60      /* rate (10 - 2550 msec, 2551 == off) */

/* Device information bits */
#define HIL_ABSOLUTE    0x40    /* absolute positioning data */
#define HIL_16_BITS     0x20    /* 16 bit position accuracy */
#define HIL_IOB         0x10    /* I/O description byte follows */
#define HIL_AXMASK      0x03    /* Number of axes supported */

#define HILIOB_PROMPT   0x80    /* prompt and acknowledge (leds) supported */
#define HILIOB_PMASK    0x70    /* number of prompt & acknowledge supported */
#define HILIOB_PIO      0x08    /* proximity in/out (pressure) supported */
#define HILIOB_BMASK    0x07    /* number of buttons supported */

You are viewing proxied material from ftp.icm.edu.pl. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.