/*      $NetBSD: btlreg.h,v 1.9 2024/06/02 12:11:36 andvar Exp $        */

typedef uint8_t physaddr[4];
typedef uint8_t physlen[4];
#define ltophys _lto4l
#define phystol _4ltol

/*
* I/O port offsets
*/
#define BT_CTRL_PORT            0       /* control (wo) */
#define BT_STAT_PORT            0       /* status (ro) */
#define BT_CMD_PORT             1       /* command (wo) */
#define BT_DATA_PORT            1       /* data (ro) */
#define BT_INTR_PORT            2       /* interrupt status (ro) */

/*
* BT_CTRL bits
*/
#define BT_CTRL_HRST            0x80    /* Hardware reset */
#define BT_CTRL_SRST            0x40    /* Software reset */
#define BT_CTRL_IRST            0x20    /* Interrupt reset */
#define BT_CTRL_SCRST           0x10    /* SCSI bus reset */

/*
* BT_STAT bits
*/
#define BT_STAT_STST            0x80    /* Self test in Progress */
#define BT_STAT_DIAGF           0x40    /* Diagnostic Failure */
#define BT_STAT_INIT            0x20    /* Mbx Init required */
#define BT_STAT_IDLE            0x10    /* Host Adapter Idle */
#define BT_STAT_CDF             0x08    /* cmd/data out port full */
#define BT_STAT_DF              0x04    /* Data in port full */
#define BT_STAT_INVDCMD         0x01    /* Invalid command */

/*
* BT_CMD opcodes
*/
#define BT_NOP                  0x00    /* No operation */
#define BT_MBX_INIT             0x01    /* Mbx initialization */
#define BT_START_SCSI           0x02    /* start scsi command */
#define BT_INQUIRE_REVISION     0x04    /* Adapter Inquiry */
#define BT_MBO_INTR_EN          0x05    /* Enable MBO available interrupt */
#if 0
#define BT_SEL_TIMEOUT_SET      0x06    /* set selection time-out */
#define BT_BUS_ON_TIME_SET      0x07    /* set bus-on time */
#define BT_BUS_OFF_TIME_SET     0x08    /* set bus-off time */
#define BT_SPEED_SET            0x09    /* set transfer speed */
#endif
#define BT_INQUIRE_DEVICES      0x0a    /* return installed devices 0-7 */
#define BT_INQUIRE_CONFIG       0x0b    /* return configuration data */
#define BT_TARGET_EN            0x0c    /* enable target mode */
#define BT_INQUIRE_SETUP        0x0d    /* return setup data */
#define BT_ECHO                 0x1e    /* Echo command data */
#define BT_INQUIRE_DEVICES_2    0x23    /* return installed devices 8-15 */
#define BT_MBX_INIT_EXTENDED    0x81    /* Mbx initialization */
#define BT_INQUIRE_REVISION_3   0x84    /* Get 3rd firmware version byte */
#define BT_INQUIRE_REVISION_4   0x85    /* Get 4th firmware version byte */
#define BT_INQUIRE_MODEL        0x8b    /* Get hardware ID and revision */
#define BT_INQUIRE_PERIOD       0x8c    /* Get synchronous period */
#define BT_INQUIRE_EXTENDED     0x8d    /* Adapter Setup Inquiry */
#define BT_ROUND_ROBIN          0x8f    /* Enable/Disable(default) round robin */

/*
* BT_INTR bits
*/
#define BT_INTR_ANYINTR         0x80    /* Any interrupt */
#define BT_INTR_SCRD            0x08    /* SCSI reset detected */
#define BT_INTR_HACC            0x04    /* Command complete */
#define BT_INTR_MBOA            0x02    /* MBX out empty */
#define BT_INTR_MBIF            0x01    /* MBX in full */

struct bt_mbx_out {
       physaddr ccb_addr;
       u_char dummy[3];
       u_char cmd;
};

struct bt_mbx_in {
       physaddr ccb_addr;
       u_char dummy[3];
       u_char stat;
};

/*
* mbo.cmd values
*/
#define BT_MBO_FREE     0x0     /* MBO entry is free */
#define BT_MBO_START    0x1     /* MBO activate entry */
#define BT_MBO_ABORT    0x2     /* MBO abort entry */

/*
* mbi.stat values
*/
#define BT_MBI_FREE     0x0     /* MBI entry is free */
#define BT_MBI_OK       0x1     /* completed without error */
#define BT_MBI_ABORT    0x2     /* aborted ccb */
#define BT_MBI_UNKNOWN  0x3     /* Tried to abort invalid CCB */
#define BT_MBI_ERROR    0x4     /* Completed with error */

#if     defined(BIG_DMA)
#define BT_NSEG 2048    /* Number of scatter gather segments - to much vm */
#else
#define BT_NSEG (MAXPHYS / PAGE_SIZE)
#endif /* BIG_DMA */

struct bt_scat_gath {
       physlen seg_len;
       physaddr seg_addr;
};

struct bt_ccb {
       u_char opcode;
       u_char:3, data_in:1, data_out:1,:3;
       u_char scsi_cmd_length;
       u_char req_sense_length;
       /*------------------------------------longword boundary */
       physlen data_length;
       /*------------------------------------longword boundary */
       physaddr data_addr;
       /*------------------------------------longword boundary */
       u_char dummy1[2];
       u_char host_stat;
       u_char target_stat;
       /*------------------------------------longword boundary */
       u_char target;
       u_char lun;
       u_char scsi_cmd[12];
       u_char dummy2[1];
       u_char link_id;
       /*------------------------------------longword boundary */
       physaddr link_addr;
       /*------------------------------------longword boundary */
       physaddr sense_ptr;
/*-----end of HW fields-----------------------longword boundary */
       struct scsi_sense_data scsi_sense;
       /*------------------------------------longword boundary */
       struct bt_scat_gath scat_gath[BT_NSEG];
       /*------------------------------------longword boundary */
       TAILQ_ENTRY(bt_ccb) chain;
       struct bt_ccb *nexthash;
       long hashkey;
       struct scsipi_xfer *xs;         /* the scsi_xfer for this cmd */
       int flags;
#define CCB_ALLOC       0x01
#define CCB_ABORT       0x02
#ifdef BTDIAG
#define CCB_SENDING     0x04
#endif
       int timeout;
};

struct bt_buf {
       TAILQ_ENTRY(bt_buf) chain;
       char    buf[4096 - 2 * sizeof(struct bt_buf *)];
};

/*
* opcode fields
*/
#define BT_INITIATOR_CCB        0x00    /* SCSI Initiator CCB */
#define BT_TARGET_CCB           0x01    /* SCSI Target CCB */
#define BT_INIT_SCAT_GATH_CCB   0x02    /* SCSI Initiator with scatter gather */
#define BT_RESET_CCB            0x81    /* SCSI Bus reset */

/*
* bt_ccb.host_stat values
*/
#define BT_OK           0x00    /* cmd ok */
#define BT_LINK_OK      0x0a    /* Link cmd ok */
#define BT_LINK_IT      0x0b    /* Link cmd ok + int */
#define BT_SEL_TIMEOUT  0x11    /* Selection time out */
#define BT_OVER_UNDER   0x12    /* Data over/under run */
#define BT_BUS_FREE     0x13    /* Bus dropped at unexpected time */
#define BT_INV_BUS      0x14    /* Invalid bus phase/sequence */
#define BT_BAD_MBO      0x15    /* Incorrect MBO cmd */
#define BT_BAD_CCB      0x16    /* Incorrect ccb opcode */
#define BT_BAD_LINK     0x17    /* Not same values of LUN for links */
#define BT_INV_TARGET   0x18    /* Invalid target direction */
#define BT_CCB_DUP      0x19    /* Duplicate CCB received */
#define BT_INV_CCB      0x1a    /* Invalid CCB or segment list */

struct bt_extended_inquire {
       struct {
               u_char  opcode;
               u_char  len;
       } cmd;
       struct {
               u_char  bus_type;       /* Type of bus connected to */
#define BT_BUS_TYPE_24BIT       'A'     /* ISA bus */
#define BT_BUS_TYPE_32BIT       'E'     /* EISA/VLB/PCI bus */
#define BT_BUS_TYPE_MCA         'M'     /* MicroChannel bus */
               u_char  bios_address;   /* Address of adapter BIOS */
               u_short max_segment;    /* ? */
       } reply;
};

struct bt_config {
       struct {
               u_char  opcode;
       } cmd;
       struct {
               u_char  chan;
               u_char  intr;
               u_char  scsi_dev:3;
               u_char  :5;
       } reply;
};

struct bt_toggle {
       struct {
               u_char  opcode;
               u_char  enable;
       } cmd;
};

struct bt_mailbox {
       struct {
               u_char  opcode;
               u_char  nmbx;
               physaddr addr;
       } cmd;
};

struct bt_model {
       struct {
               u_char  opcode;
               u_char  len;
       } cmd;
       struct {
               u_char  id[4];          /* i.e bt742a -> '7','4','2','A' */
               u_char  version[2];     /* i.e Board Revision 'H' -> 'H', 0x00 */
       } reply;
};

struct bt_revision {
       struct {
               u_char  opcode;
       } cmd;
       struct {
               u_char  board_type;
               u_char  custom_feature;
               char    firm_revision;
               u_char  firm_version;
       } reply;
};

struct bt_digit {
       struct {
               u_char  opcode;
       } cmd;
       struct {
               u_char  digit;
       } reply;
};

struct bt_devices {
       struct {
               u_char  opcode;
       } cmd;
       struct {
               u_char  junk[8];
       } reply;
};

struct bt_setup {
       struct {
               u_char  opcode;
               u_char  len;
       } cmd;
       struct {
               u_char  sync_neg:1;
               u_char  parity:1;
               u_char  :6;
               u_char  speed;
               u_char  bus_on;
               u_char  bus_off;
               u_char  num_mbx;
               u_char  mbx[3];         /*XXX */
               /* doesn't make sense with 32bit addresses */
               struct {
                       u_char  offset:4;
                       u_char  period:3;
                       u_char  valid:1;
               } sync[8];
               u_char  disc_sts;
       } reply;
};

struct bt_period {
       struct {
               u_char  opcode;
               u_char  len;
       } cmd;
       struct {
               u_char  period[8];
       } reply;
};

#define INT9    0x01
#define INT10   0x02
#define INT11   0x04
#define INT12   0x08
#define INT14   0x20
#define INT15   0x40

#define EISADMA 0x00
#define CHAN0   0x01
#define CHAN5   0x20
#define CHAN6   0x40
#define CHAN7   0x80

You are viewing proxied material from ftp.icm.edu.pl. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.