INSTALL(8) NetBSD System Manager's Manual INSTALL(8)
NAME
INSTALL -- Installation procedure for NetBSD/evbppc.
CONTENTS
About this Document
What is NetBSD?
Dedication
Changes Between The NetBSD 8 and 9 Releases
Installation and Partitioning Changes
Features to be removed in a later release
The NetBSD Foundation
Sources of NetBSD
NetBSD 9.4 Release Contents
NetBSD/evbppc subdirectory structure
Binary distribution sets
NetBSD/evbppc System Requirements and Supported Devices
Supported devices
Unsupported devices
Supported boot devices and media
Getting the NetBSD System on to Useful Media
Preparing your System for NetBSD installation
Booting over a serial line
Booting from the network
Installing the NetBSD System
Booting the installer
Example of a normal boot
Common Problems and Error Messages
Running the sysinst installation program
Introduction
Possible hardware problems
General
Quick install
Booting NetBSD
Network configuration
Installation drive selection and parameters
Selecting which sets to install
Partitioning the disk
Preparing your hard disk
Getting the distribution sets
Installation from CD-ROM
Installation using FTP
Installation using NFS
Installation from an unmounted file system
Installation from a local directory
Extracting the distribution sets
Configure additional items
Finalizing your installation
Post installation steps
Upgrading a previously-installed NetBSD System
Compatibility Issues With Previous NetBSD Releases
Using online NetBSD documentation
Administrivia
Thanks go to
Legal Mumbo-Jumbo
The End
DESCRIPTION
About this Document
This document describes the installation procedure for
NetBSD 9.4 on the evbppc platform. It is available in four
different formats titled INSTALL.ext, where .ext is one of
.ps, .html, .more, or .txt:
.ps PostScript.
.html Standard Internet HTML.
.more The enhanced text format used on UNIX-like
systems by the more(1) and less(1) pager util-
ity programs. This is the format in which the
on-line man pages are generally presented.
.txt Plain old ASCII.
You are reading the ASCII version.
What is NetBSD?
The NetBSD Operating System is a fully functional Open
Source UNIX-like operating system derived from the Univer-
sity of California, Berkeley Networking Release 2 (Net/2),
4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on many
different different system architectures (ports) across a
variety of distinct CPU families, and is being ported to
more. The NetBSD 9.4 release contains complete binary
releases for most of these system architectures, with pre-
liminary support for the others included in source form.
Please see the NetBSD website:
https://www.NetBSD.org/ for
information on them.
NetBSD is a completely integrated system. In addition to
its highly portable, high performance kernel, NetBSD fea-
tures a complete set of user utilities, compilers for sev-
eral languages, the X Window System, firewall software and
numerous other tools, all accompanied by full source code.
NetBSD is a creation of the members of the Internet commu-
nity. Without the unique cooperation and coordination the
net makes possible, NetBSD would not exist.
Dedication
NetBSD 9.4 is dedicated to the memory of Wayne Knowles, who
passed away in December 2022.
Wayne was a long term contributor, working mostly on low
level Mips code.
Beyond his technical contributions, Wayne was always helpful
and friendly. His example encouraged users to contribute to
the project and share their work with the community.
Changes Between The NetBSD 8 and 9 Releases
The NetBSD 9.4 release provides many significant changes,
including support for many new devices, hundreds of bug
fixes, new and updated kernel subsystems, and numerous user-
land enhancements. The result of these improvements is a
stable operating system fit for production use that rivals
most commercially available systems.
It is impossible to completely summarize the massive devel-
opment that went into the NetBSD 9.4 release. The complete
list of changes can be found in the following files:
CHANGES:
https://cdn.NetBSD.org/pub/NetBSD/NetBSD-9.4/CHANGES
CHANGES-9.1:
https://cdn.NetBSD.org/pub/NetBSD/NetBSD-9.4/CHANGES-9.1
CHANGES-9.2:
https://cdn.NetBSD.org/pub/NetBSD/NetBSD-9.4/CHANGES-9.2
CHANGES-9.3:
https://cdn.NetBSD.org/pub/NetBSD/NetBSD-9.4/CHANGES-9.3
CHANGES-9.4:
https://cdn.NetBSD.org/pub/NetBSD/NetBSD-9.4/CHANGES-9.4
files in the top level directory of the NetBSD 9.4 release
tree.
Installation and Partitioning Changes
The sysinst installation program has been reworked for this
release.
It now supports arbitrary big disks and offers GPT parti-
tions as alternative to MBR/fdisk partitions on a lot archi-
tectures.
Unfortunately it has not been tested on all hardware sup-
ported by NetBSD. If you have problems partitioning the
target disk or installing the system, please report bugs
with as much details as possible. See the Administrivia
section below on how to report bugs or contact other users
and ask for support.
Features to be removed in a later release
The following features are to be removed from NetBSD in the
future:
o groff(1). Man pages are now handled with mandoc(1), and
groff(1) can still be found in pkgsrc as textproc/groff.
The NetBSD Foundation
The NetBSD Foundation is a tax exempt, not-for-profit
501(c)(3) corporation that devotes itself to the traditional
goals and Spirit of the NetBSD Project and owns the trade-
mark of the word ``NetBSD''. It supports the design, devel-
opment, and adoption of NetBSD worldwide. More information
on the NetBSD Foundation, its composition, aims, and work
can be found at:
https://www.NetBSD.org/foundation/
Sources of NetBSD
Refer to mirrors:
https://www.NetBSD.org/mirrors/
NetBSD 9.4 Release Contents
The root directory of the NetBSD 9.4 release is organized as
follows:
.../NetBSD-9.4/
CHANGES Changes between the 8.0 and 9.0 releases.
CHANGES-9.0 Changes between the initial 9.0 branch and
final release of 9.0.
CHANGES-9.1 Changes between the 9.0 and the 9.1 release.
CHANGES-9.2 Changes between the 9.1 and the 9.2 release.
CHANGES-9.3 Changes between the 9.2 and the 9.3 release.
CHANGES-9.4 Changes between the 9.3 and the 9.4 release.
CHANGES.prev Changes in previous NetBSD releases.
LAST_MINUTE Last minute changes and notes about the
release.
README.files README describing the distribution's contents.
images/ Images (ISO 9660 or USB) for installing
NetBSD. Depending on your system, these may
be bootable.
source/ Source distribution sets; see below.
In addition to the files and directories listed above, there
is one directory per architecture, for each of the architec-
tures for which NetBSD 9.4 has a binary distribution.
The source distribution sets can be found in subdirectories
of the source subdirectory of the distribution tree. They
contain the complete sources to the system. The source dis-
tribution sets are as follows:
gnusrc This set contains the ``gnu'' sources, including
the source for the compiler, assembler, groff, and
the other GNU utilities in the binary distribution
sets.
sharesrc This set contains the ``share'' sources, which
include the sources for the man pages not associ-
ated with any particular program; the sources for
the typesettable document set; the dictionaries;
and more.
src This set contains all of the base NetBSD 9.4
sources which are not in gnusrc, sharesrc, or
syssrc.
syssrc This set contains the sources to the NetBSD 9.4
kernel for all architectures as well as the
config(1) utility.
xsrc This set contains the sources to the X Window Sys-
tem.
All the above source sets are located in the source/sets
subdirectory of the distribution tree.
The source sets are distributed as compressed tar files.
Except for the pkgsrc set, which is traditionally unpacked
into /usr/pkgsrc, all sets may be unpacked into /usr/src
with the command:
# cd / ; tar -zxpf set_name.tgz
In each of the source distribution set directories, there
are files which contain the checksums of the files in the
directory:
MD5 MD5 digests in the format produced by the com-
mand:
cksum -a MD5 file.
SHA512 SHA512 digests in the format produced by the
command:
cksum -a SHA512 file.
The SHA512 digest is safer, but MD5 checksums are provided
so that a wider range of operating systems can check the
integrity of the release files.
NetBSD/evbppc subdirectory structure
The evbppc-specific portion of the NetBSD 9.4 release is
found in the evbppc subdirectory of the distribution:
.../NetBSD-9.4/evbppc/. It contains the following files and
directories:
INSTALL.html
INSTALL.ps
INSTALL.txt
INSTALL.more Installation notes in various file formats,
including this file. The .more file contains
underlined text using the more(1) conventions
for indicating italic and bold display.
binary/
kernel/
netbsd-EV64260.gz
A gzipped kernel (in ELF
format) for the Marvell
EV-64260.
netbsd.img-EV64260.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-EXPLORA451.gz
A gzipped kernel (in ELF
format) for the NCD
Explora451 NC.
netbsd.img-EXPLORA451.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-INSTALL_OPENBLOCKS266.gz
A gzipped install kernel
(in ELF format) for the
Plat'Home OpenBlockS266
microserver.
netbsd-INSTALL_OPENBLOCKS266.img.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-INSTALL_OPENBLOCKS266.symbols.gz
Symbols for
netbsd-INSTALL_OPENBLOCKS266.gz.
netbsd-INSTALL_WALNUT.gz
A gzipped install kernel
(in ELF format) for the
IBM PowerPC 405GP Walnut
evaluation board.
netbsd-INSTALL_WALNUT.img.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-INSTALL_WALNUT.symbols.gz
Symbols for
netbsd-INSTALL_WALNUT.gz.
netbsd-OPENBLOCKS200.gz
A gzipped kernel (in ELF
format) for the Plat'Home
OpenBlockS200.
netbsd.img-OPENBLOCKS200.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-OPENBLOCKS266.gz
A gzipped kernel (in ELF
format) for the Plat'Home
OpenBlockS266 microserver.
netbsd.img-OPENBLOCKS266.gz
Same as the above, but in
the format expected by the
firmware.
netbsd-PMPPC.gz
A gzipped kernel (in ELF
format) for Artesyn PM/PPC
boards.
netbsd-WALNUT.gz
A gzipped kernel (in ELF
format) for the IBM Pow-
erPC 405GP Walnut evalua-
tion board.
netbsd.img-WALNUT.gz
Same as the above, but in
the format expected by the
firmware.
sets/ evbppc binary distribution sets; see
below.
installation/
Binary distribution sets
The NetBSD evbppc binary distribution sets contain the bina-
ries which comprise the NetBSD 9.4 release for evbppc. The
binary distribution sets can be found in the
evbppc/binary/sets subdirectory of the NetBSD 9.4 distribu-
tion tree, and are as follows:
base The NetBSD 9.4 evbppc base binary distribution.
You must install this distribution set. It con-
tains the base NetBSD utilities that are necessary
for the system to run and be minimally functional.
comp Things needed for compiling programs. This set
includes the system include files (/usr/include)
and the various system libraries (except the shared
libraries, which are included as part of the base
set). This set also includes the manual pages for
all of the utilities it contains, as well as the
system call and library manual pages.
debug This distribution set contains debug information
for all base system utilities. It is useful when
reporting issues with binaries or during develope-
ment. This set is huge, if the target disk is
small, do not install it.
etc This distribution set contains the system configu-
ration files that reside in /etc and in several
other places. This set must be installed if you
are installing the system from scratch, but should
not be used if you are upgrading.
games This set includes the games and their manual pages.
kern-EV64260
This set contains a NetBSD/evbppc 9.4 kernel in ELF
format named /netbsd and the same kernel in the
format needed by the bootloader as /netbsd.img.
These kernels are specific to the Marvell EV-64260.
kern-EXPLORA451
This set contains a NetBSD/evbppc 9.4 kernel in ELF
format named /netbsd and the same kernel in the
format needed by the bootloader as /netbsd.img.
These kernels are specific to the NCD Explora451
NC.
kern-OPENBLOCKS266
This set contains a NetBSD/evbppc 9.4 kernel in ELF
format named /netbsd and the same kernel in the
format needed by the bootloader as /netbsd.img.
These kernels are specific to the Plat'Home Open-
BlockS266 microserver.
kern-PMPPC
This set contains a NetBSD/evbppc 9.4 kernel in ELF
format named /netbsd and the same kernel in the
format needed by the bootloader as /netbsd.img.
These kernels are specific to Artesyn PM/PPC
boards.
kern-WALNUT
This set contains a NetBSD/evbppc 9.4 kernel in ELF
format named /netbsd and the same kernel in the
format needed by the bootloader as /netbsd.img.
These kernels are specific to the IBM 405GP based
Walnut evaluation board.
man This set includes all of the manual pages for the
binaries and other software contained in the base
set. Note that it does not include any of the man-
ual pages that are included in the other sets.
misc This set includes the system dictionaries, the
typesettable document set, and other files from
/usr/share.
modules This set includes kernel modules to add functional-
ity to a running system.
rescue This set includes the statically linked emergency
recover binaries installed in /rescue.
text This set includes NetBSD's text processing tools,
including groff(1), all related programs, and their
manual pages.
NetBSD maintains its own set of sources for the X Window
System in order to assure tight integration and compatibil-
ity. These sources are based on X.Org. Binary sets for the
X Window System are distributed with NetBSD. The sets are:
xbase The basic files needed for a complete X client
environment. This does not include the X servers.
xcomp The extra libraries and include files needed to
compile X source code.
xdebug This distribution set contains debug information
for all X11 binaries. It is useful when reporting
issues with these binaries or during developement.
This set is huge, if the target disk is small, do
not install it.
xfont Fonts needed by the X server and by X clients.
xetc Configuration files for X which could be locally
modified.
xserver The X server.
The evbppc binary distribution sets are distributed as
gzipped tar files named with the extension .tgz, e.g.
base.tgz.
The instructions given for extracting the source sets work
equally well for the binary sets, but it is worth noting
that if you use that method, the filenames stored in the
sets are relative and therefore the files are extracted
below the current directory. Therefore, if you want to
extract the binaries into your system, i.e. replace the
system binaries with them, you have to run the tar -xzpf
command from the root directory ( / ) of your system.
Note: Each directory in the evbppc binary distribution also
has its own checksum files, just as the source dis-
tribution does.
NetBSD/evbppc System Requirements and Supported Devices
NetBSD/evbppc is a port of NetBSD to PowerPC based evalua-
tion boards. At the present time, the following boards are
supported:
o Artesyn's PM/PPC board
o IBM PowerPC 405GP based Walnut
o Marvell PowerPC 750 based EV-64260
o NCD Explora451 NC
o Plat'Home OpenBlockS200
o Plat'Home OpenBlockS266 microserver
However, this documentation is specific to installing
NetBSD/evbppc on the Walnut board only.
Supported devices
o Ethernet: The built-in Ethernet card is not sup-
ported, so another PCI Ethernet card supported by
NetBSD must be provided if you want to use
NetBSD/evbppc on a network. Any PCI Ethernet card
supported by NetBSD should work.
o SCSI: Any PCI SCSI card supported by NetBSD should
work, as should most SCSI disk/tape/CD-ROM
devices.
o IDE:
- Promise Ultra66 (pciide)
- Other PCI IDE controllers should work, but
there are no reports.
- Most IDE disk/CD-ROM/ATAPI devices should
work.
o Audio
- PCI audio cards, although none have been
tested.
o Serial ports
- On-board serial ports (com0) and (com1)
- Some PCI serial ports should work, but no one
has tried them
o PCI cards
- Most MI PCI cards should work, although very
few have been tested with NetBSD/evbppc
http://www.NetBSD.org/support/hardware/pci.html
Unsupported devices
o On-board Ethernet
Note: This does not concern booting the kernel
itself, since that is done by the firmware. For
using an NFS root you will have to provide a sup-
ported network card, though.
Supported boot devices and media
The firmware only supports booting from network or the
serial port, so you cannot boot from disk even if you
install a disk controller. Instructions for booting from
serial port are not provided; in the following we will
describe how to setup netbooting.
The first step is setting the IP addresses of both the wal-
nut itself and the host that will be serving the kernel
image. From the main menu, choose 3 to set the IP address
of the machine:
1 - Enable/disable tests
2 - Enable/disable boot devices
3 - Change IP addresses
4 - Ping test
5 - Toggle ROM monitor debugger
6 - Toggle automatic menu
7 - Display configuration
8 - Save changes to configuration
9 - Set baud rate for s1 boot
A - Enable/disable I cache (Enabled )
B - Enable/disable D cache (Enabled )
0 - Exit menu and continue
-> 3
Set the IP address for the local Ethernet with 1:
--- CHANGE IP ADDRESS ---
Device List:
001 Enabled Ethernet [ENET]
local=0.0.0.0 remote=0.0.0.0 hwaddr=0004ace312bd
004 Disabled Serial Port 2 [S2]
local=8.1.1.2 remote=255.255.255.255 hwaddr=ffffffffffff
----------------------------
select device to change ->1
1 - Change local address
2 - Change remote address
0 - Return to main menu
->1
Current IP address = (0.0.0.0)
Enter new IP address ->Enter IP address in dot notation, (eg. 8.1.1.2)
Here you enter the machine's IP address, e.g. 10.0.0.1. Now
you need to do the same thing to set the host IP address
(choice 2 from the menu above).
Once both the local and remote addresses are set, you can
use the ping test to make sure the ethernet is working; or
you can simply use option 0, "Exit menu and continue" to try
to boot the machine, if you already set up the remote
machine to provide a kernel image. For details on how to do
that, see the Booting from the network section below.
You should now be able to boot the operating system.
Getting the NetBSD System on to Useful Media
Installation is supported from several media types, includ-
ing:
o CD-ROM / DVD / USB-stick
o FTP
o Remote NFS partition
o Tape
o Existing NetBSD partitions, if performing an
upgrade
The steps necessary to prepare the distribution sets for
installation depend upon which installation medium you
choose. The steps for the various media are outlined below.
CD-ROM / DVD / USB-stick Find out where the distribution
set files are on the CD-ROM, DVD
or USB stick. Likely locations
are binary/sets and
evbppc/binary/sets. (You only
need to know this if you are mix-
ing installer and installation
media from different versions -
the installer will know the proper
default location for the sets it
comes with).
Proceed to the instructions on
installation.
FTP The preparations for this instal-
lation/upgrade method are easy;
all you need to do is make sure
that there's an FTP site from
which you can retrieve the NetBSD
distribution when you're about to
install or upgrade. If you don't
have DHCP available on your net-
work, you will need to know the
numeric IP address of that site,
and, if it's not on a network
directly connected to the machine
on which you're installing or
upgrading NetBSD, you need to know
the numeric IP address of the
router closest to the NetBSD
machine. Finally, you need to
know the numeric IP address of the
NetBSD machine itself.
Once you have this information,
you can proceed to the next step
in the installation or upgrade
process. If you're installing
NetBSD from scratch, go to the
section on preparing your hard
disk, below. If you're upgrading
an existing installation, go
directly to the section on upgrad-
ing.
NFS Place the NetBSD distribution sets
you wish to install into a direc-
tory on an NFS server, and make
that directory mountable by the
machine on which you are
installing or upgrading NetBSD.
This will probably require modify-
ing the /etc/exports file on the
NFS server and resetting its mount
daemon (mountd). (Both of these
actions will probably require
superuser privileges on the
server.)
You need to know the numeric IP
address of the NFS server, and, if
you don't have DHCP available on
your network and the server is not
on a network directly connected to
the machine on which you're
installing or upgrading NetBSD,
you need to know the numeric IP
address of the router closest to
the NetBSD machine. Finally, you
need to know the numeric IP
address of the NetBSD machine
itself.
Once the NFS server is set up
properly and you have the informa-
tion mentioned above, you can pro-
ceed to the next step in the
installation or upgrade process.
If you're installing NetBSD from
scratch, go to the section on pre-
paring your hard disk, below. If
you're upgrading an existing
installation, go directly to the
section on upgrading.
Tape To install NetBSD from a tape, you
need to make a tape that contains
the distribution set files, in
`tar' format.
If you're making the tape on a
UNIX-like system, the easiest way
to do so is probably something
like:
# tar -cf tape_device
dist_sets
where tape_device is the name of
the tape device that represents
the tape drive you're using. This
might be /dev/rst0, or something
similar, but it will vary from
system to system. In the above
example, dist_sets is a list of
filenames corresponding to the
distribution sets that you wish to
place on the tape. For instance,
to put the kern-GENERIC, base, and
etc distributions on tape (the
absolute minimum required for
installation), you would do the
following:
# cd .../NetBSD-9.4
# cd evbppc/binary
# tar -cf tape_device
kern-GENERIC.tgz base.tgz
etc.tgz
Note: You still need to fill in
tape_device in the example.
Once you have the files on the
tape, you can proceed to the next
step in the installation or
upgrade process. If you're
installing NetBSD from scratch, go
to the section on preparing your
hard disk, below. If you're
upgrading an existing installa-
tion, go directly to the section
on upgrading.
Preparing your System for NetBSD installation
When installing NetBSD for your NetBSD/evbppc system, you
have two options: Via serial port or via network. The
firmware does not support loading the kernel from a disk.
Booting over a serial line
This is not currently documented or supported. If you would
like to attempt this and supply documentation, please do!
Booting from the network
1. Introduction
To netboot a evbppc, you must configure one or more
servers to provide information and files to your evbppc
(the `client'). If you are using NetBSD (any architec-
ture) on your netboot server(s), the information pro-
vided here should be sufficient to configure every-
thing. Additionally, you may wish to look at the
diskless(8) manual page and the manual pages for each
daemon you'll be configuring. If the server(s) are
another operating system, you should consult the NetBSD
Diskless HOW-TO, which will walk you through the steps
necessary to configure the netboot services on a vari-
ety of platforms:
https://www.NetBSD.org/docs/network/netboot/
You may either netboot the installer so you can install
onto a locally attached disk, or you may run your sys-
tem entirely over the network.
Briefly, the netboot process involves discovery, kernel
and file system stages. In the first stage, the client
discovers information about where to find the kernel
image. Once the kernel is loaded, it starts executing.
For RAM disk kernels, it mounts the RAM disk file sys-
tem and begins executing the installer from the RAM
disk. For normal (non-RAM disk) kernels, the kernel
tries to mount the NFS share that had the kernel and
starts executing the installation tools or init(8).
All evbppc systems use BOOTP for the discovery stage.
TFTP is used in the bootstrap phase to download the
kernel via the on-board Ethernet card by the firmware.
Thus, NetBSD support for the on-board card is not
needed in this step. For NFS mounting a file system on
the other hand, NetBSD support for the Ethernet card is
needed, and the on-board one will not suffice; you have
to provide a second Ethernet card supported by NetBSD .
We will use `CC:CC:CC:CC:CC:CC' as the MAC address
(ethernet hardware address) of your netboot client
machine. You should have determined this address in an
earlier stage. In this example, we will use
`192.168.1.10' as the IP address of your client and
`client.test.net' as its name. We will assume you're
providing all of your netboot services on one machine
called `server.test.net' with the client's files
exported from the directory /export/client/root. You
should, of course, replace all of these with the names,
addresses, and paths appropriate to your environment.
You should set up each netboot stage in order (i.e.,
discovery, bootstrap, kernel, and then file system) so
that you can test them as you proceed.
2. dhcpd(8) in bootpd(8) compatible mode
Put the following lines in your /etc/dhcpd.conf (see
dhcpd.conf(5) and dhcp-options(5) for more informa-
tion):
ddns-update-style none;
# Do not use any dynamic DNS features
#
allow bootp; # Allow bootp requests, thus the dhcp server
# will act as a bootp server.
#
authoritative; # master DHCP server for this subnet
#
subnet 192.168.1.0 netmask 255.255.255.0 {
# Which network interface to listen on.
# The zeros indicate the range of addresses
# that are allowed to connect.
}
group {
# Set of parameters common to all clients
# in this "group".
#
option broadcast-address 192.168.1.255;
option domain-name "test.net";
option domain-name-servers dns.test.net;
option routers router.test.net;
option subnet-mask 255.255.255.0;
#
# An individual client.
#
host client.test.net {
hardware ethernet CC:CC:CC:CC:CC:CC;
fixed-address 192.168.1.10;
#
# Name of the host (if the fixed address
# doesn't resolve to a simple name).
#
option host-name "client";
#
# Name of the kernel image to download via tftp.
# Note: Plain (ELF) kernels won't work, you
# have to use the corresponding *.img file.
#
filename "netbsd-INSTALL_WALNUT.img"
#
# Name of the bootloader or kernel
# to download via tftp.
#
# The path on the NFS server.
#
option root-path "/export/client/root";
#
# The host address of the NFS server. This is mandatory for
# NetBSD kernels even it's the same host as the DHCP server.
#
next-server server.test.net;
}
#you may paste another "host" entry here for additional
#clients on this network
}
You will need to make sure that the dhcpd.leases file
exists.
# touch /var/db/dhcpd.leases
You will need to start the dhcpd. If it's already run-
ning, you will need to restart it to force it to re-
read its configuration file. If the server is running
NetBSD, you can achieve this with:
# /etc/rc.d/dhcpd restart
3. tftpd(8)
The default configuration of the TFTP server is to run
in a chroot(8) environment in the /tftpboot directory.
Thus, the first order of business is to create this
directory:
# mkdir -p /tftpboot
Next, edit /etc/inetd.conf and uncomment the line with
the TFTP daemon:
tftp dgram udp wait root /usr/libexec/tftpd tftpd -l -s /tftpboot
Now, restart inetd(8). If the server is running
NetBSD, you can achieve this with:
# /etc/rc.d/inetd restart
Now, you need to copy the kernel for your evbppc
machine to /tftpboot. Just to be sure, let's make
everything readable.
# chmod -R a+rX /tftpboot
Sometimes, the arp(8) table gets messed up, and the
TFTP server can't communicate with the client. In this
case, it will write a log message (via syslogd(8)) to
/var/log/messages saying: `tftpd: write: Host is down'.
If this is the case, you may need to force the server
to map your client's ethernet address to its IP
address:
# arp -s client CC:CC:CC:CC:CC:CC
4. nfsd(8), mountd(8), and rpcbind(8)
You can either boot a kernel, or the RAM disk-based
installer binary/kernel/netbsd-INSTALL.img.gz. In the
first case you'll also need an NFS-mounted userland.
Let's set up the NFS server. Create the directory you
are exporting for the netboot client:
# mkdir -p /export/client/root
Put the following line in /etc/exports to enable NFS
sharing:
/export/client/root -maproot=root client.test.net
If your server is currently running an NFS server, you
only need to restart mountd(8). Otherwise, you need to
start rpcbind(8) and nfsd(8). If the server is running
NetBSD, you can achieve this with:
# /etc/rc.d/rpcbind start
# /etc/rc.d/nfsd start
# /etc/rc.d/mountd restart
5. NetBSD kernel and installation tools
If you are netbooting the installer, use
binary/kernel/netbsd-INSTALL_WALNUT.img.gz (this has
the installation tools in a RAM disk). Also, copy the
distribution files to the client's root directory.
# cp *.tgz /export/client/root
# gunzip netbsd-INSTALL.img.gz
# mv netbsd-INSTALL.img /export/client/root/netbsd
If you are running your evbppc diskless, simply use
binary/kernel/netbsd.img-WALNUT.gz.
6. Client file system
You can skip this step if you do not plan to run your
client diskless after installation. Otherwise, you
need to extract and set up the client's installation of
NetBSD. The Diskless HOW-TO describes how to provide
better security and save space on the NFS server over
the procedure listed here. See for details:
https://www.NetBSD.org/docs/network/netboot/nfs.html.
o Extracting distribution sets
# cd /export/client/root
# tar -xpzf /path/to/files/base.tgz
# tar -xpzf /path/to/files/etc.tgz
Continue with the other non-essential distribution
sets if desired.
o Set up swap
# mkdir /export/client/root/swap
# dd if=/dev/zero of=/export/client/swap bs=4k count=4k
# echo '/export/client/swap -maproot=root:wheel client.test.net' >> /etc/exports
# /etc/rc.d/mountd restart
This creates a 16 MB swap file and exports it to
the client.
o Create device nodes
# cd /export/client/root/dev
# ./MAKEDEV all
This procedure only works on NetBSD hosts.
o Set up the client's fstab(5)
Create a file in /export/client/root/etc/fstab with
the following lines:
server:/export/client/swap none swap sw,nfsmntpt=/swap
server:/export/client/root / nfs rw 0 0
o Set up the client's rc.conf(5)
Edit /export/client/root/etc/rc.conf
rc_configured=YES
hostname="client"
defaultroute="192.168.1.1"
nfs_client=YES
auto_ifconfig=NO
net_interfaces=""
Make sure rc does not reconfigure the network
device since it will lose its connection to the NFS
server with your root file system.
o Set up the client's hosts(5) file.
Edit /export/client/root/etc/hosts
::1 localhost
127.0.0.1 localhost
192.168.1.10 client.test.net client
192.168.1.5 server.test.net server
7. Setting up the server daemons
If you want these services to start up every time you
boot your server, make sure the following lines are
present in your /etc/rc.conf:
nfs_server=YES # enable server daemons
mountd=YES
rpcbind=YES rpcbind_flags="-l" # -l logs libwrap
Also, you'll need to make sure the tftpd line in
/etc/inetd.conf remains uncommented.
Installing the NetBSD System
Booting the installer
The kernel starts automatically once it is loaded.
Example of a normal boot
If you already configured the network settings, just press
`0' from the boot menu to boot.
Common Problems and Error Messages
Do not use the plain ELF kernel as the file provided to the
firmware, use the ``netbsd.img'' file (which is in the for-
mat the firmware expects). Of course, you should put the
matching ``netbsd'' as /netbsd on your root file system,
otherwise some kernel grovellers won't work.
Running the sysinst installation program
1. Introduction
Using sysinst, installing NetBSD is a relatively easy
process. Still, you should read this document and have
it available during the installation process. This
document tries to be a good guide to the installation,
and as such, covers many details for the sake of com-
pleteness. Do not let this discourage you; the install
program is not hard to use.
2. Possible hardware problems
Should you encounter hardware problems during installa-
tion, try rebooting after unplugging removable devices
you don't need for installation. Non-removable devices
can be disabled with userconf (use boot -c to enter
it).
3. General
The following is a walk-through of the steps you will
take while installing NetBSD on your hard disk.
sysinst is a menu driven program that guides you
through the installation process. Sometimes questions
will be asked, and in many cases the default answer
will be displayed in brackets (``[ ]'') after the ques-
tion. If you wish to stop the installation, you may
press CONTROL-C at any time, but if you do, you'll have
to begin the installation process again from scratch by
running the /sysinst program from the command prompt.
It is not necessary to reboot.
4. Quick install
First, let's describe a quick install. The other sec-
tions of this document go into the installation proce-
dure in more detail, but you may find that you do not
need this. If you want detailed instructions, skip to
the next section. This section describes a basic
installation, using a CD / DVD as the install media.
o What you need.
- The distribution sets (in this example, they
are on the CD or DVD).
- Some form of bootable media, described above.
- A minimum of of memory installed.
- An optical drive.
- A hard drive with at least 600 MB of free space
for a complete base install, not including room
for swap. If you wish to install the X Window
System as well, you will need at least 225 MB
more.
o The Quick Installation
- Boot the system as described above. You should
be at the sysinst main menu.
.***********************************************.
* NetBSD-9.4 Install System *
* *
*>a: Install NetBSD to hard disk *
* b: Upgrade NetBSD on a hard disk *
* c: Re-install sets or install additional sets *
* d: Reboot the computer *
* e: Utility menu *
* f: Config menu *
* x: Exit Install System *
.***********************************************.
- If you wish, you can configure some network
settings immediately by choosing the Utility
menu and then Configure network. It isn't
actually required at this point, but it may be
more convenient. Go back to the main menu.
- Choose Install.
- You will be guided through the setup of your
disk.
- You will be asked to choose which distribution
sets to install.
- When prompted, choose CD-ROM as the install
medium if booted from CD-ROM. The default val-
ues for the path and device should be ok.
- After the installation process has completed,
you will be brought back to the main menu,
where you should select Reboot, after you have
removed the bootfloppy from the drive.
- NetBSD will now boot. If you didn't set a
password for the root user when prompted by
sysinst, logging in as root and setting a pass-
word should be your first task. You are also
advised to read afterboot(8).
5. Booting NetBSD
You may want to read the boot messages, to notice your
disk's name and capacity. Its name will be something
like sd0 or wd0 and the geometry will be printed on a
line that begins with its name. As mentioned above,
you may need your disk's geometry when creating
NetBSD's partitions. You will also need to know the
name, to tell sysinst which disk to use. The most
important thing to know is that wd0 is NetBSD's name
for your first IDE disk, wd1 the second, etc. sd0 is
your first SCSI disk, sd1 the second, etc.
Once NetBSD has booted and printed all the boot mes-
sages, you will be presented with a welcome message and
a main menu. It will also include instructions for
using the menus.
6. Network configuration
If you do not intend to use networking during the
installation, but you do want your machine to be con-
figured for networking once it is installed, you should
first go to the Utility menu and select the Configure
network option. If you only want to temporarily use
networking during the installation, you can specify
these parameters later. If you are not using the
Domain Name System (DNS), you can give an empty
response when asked to provide a server.
7. Installation drive selection and parameters
To start the installation, select Install NetBSD to
hard disk from the main menu.
The first thing is to identify the disk on which you
want to install NetBSD. sysinst will report a list of
disks it finds and ask you for your selection. You
should see disk names like sd0 or sd1.
8. Selecting which sets to install
The next step is to choose which distribution sets you
wish to install. Options are provided for full, mini-
mal, and custom installations. If you choose sets on
your own, base, etc, and a kernel must be selected.
9. Partitioning the disk
o Choosing which portion of the disk to use.
You will be asked if you want to use the entire
disk or only part of the disk. If you decide to
use the entire disk for NetBSD, sysinst will check
for the presence of other operating systems and you
will be asked to confirm that you want to overwrite
these.
10. Editing the NetBSD disklabel
The partition table of the NetBSD part of a disk is
called a disklabel. If your disk already has a diskla-
bel written to it, you can choose Use existing
partition sizes. Otherwise, select Set sizes of NetBSD
partitions.
After you have chosen your partitions and their sizes
(or if you opted to use the existing partitions), you
will be presented with the layout of the NetBSD diskla-
bel and given one more chance to change it. For each
partition, you can set the type, offset and size, block
and fragment size, and the mount point. The type that
NetBSD uses for normal file storage is called 4.2BSD.
A swap partition has a special type called swap. Some
partitions in the disklabel have a fixed purpose.
a Root partition (/)
b Swap partition.
c The entire disk.
d-p Available for other use. Traditionally,
e is the partition mounted on /usr, but
this is historical practice and not a
fixed value.
You will then be asked to name your disk's disklabel.
The default response will be ok for most purposes. If
you choose to name it something different, make sure
the name is a single word and contains no special char-
acters. You don't need to remember this name.
11. Preparing your hard disk
You are now at the point of no return. Nothing has
been written to your disk yet, but if you confirm that
you want to install NetBSD, your hard drive will be
modified. If you are sure you want to proceed, select
yes.
The install program will now label your disk and create
the file systems you specified. The file systems will
be initialized to contain NetBSD bootstrapping binaries
and configuration files. You will see messages on your
screen from the various NetBSD disk preparation tools
that are running. There should be no errors in this
section of the installation. If there are, restart
from the beginning of the installation process. Other-
wise, you can continue the installation program after
pressing the return key.
12. Getting the distribution sets
The NetBSD distribution consists of a number of sets
that come in the form of gzipped tar files. At this
point, you will be presented with a menu which enables
you to choose from one of the following methods of
installing the sets. Some of these methods will first
transfer the sets to your hard disk, others will
extract the sets directly.
For all these methods, the first step is to make the
sets available for extraction. The sets can be made
available in a few different ways. The following sec-
tions describe each of the methods. After reading
about the method you will be using, you can continue to
the section labeled `Extracting the distribution sets'.
13. Installation from CD-ROM
When installing from a CD-ROM, you will be asked to
specify the device name for your CD-ROM drive (usually
cd0) and the directory name on the CD-ROM where the
distribution files are.
sysinst will then check that the files are actually
present in the specified location and proceed to the
extraction of the sets.
14. Installation using FTP
To install using ftp, you first need to configure your
network setup if you haven't already done so. sysinst
will help you with this, asking if you want to use
DHCP. If you do not use DHCP, you can enter network
configuration details yourself. If you do not have DNS
set up for the machine that you are installing on, you
can just press RETURN in answer to this question, and
DNS will not be used.
You will also be asked to specify the host that you
want to transfer the sets from, the directory on that
host, the account name and password used to log into
that host using ftp, and optionally a proxy server to
use. If you did not set up DNS, you will need to spec-
ify an IP address instead of a hostname for the ftp
server.
sysinst will then transfer the set files from the
remote site to your hard disk.
15. Installation using NFS
To install using NFS, you first need to configure your
network setup if you haven't already done so. sysinst
will do this for you, asking you if you want to use
DHCP. If you do not use DHCP, you can enter network
configuration details yourself. If you do not have DNS
set up for the machine that you are installing on, you
can just press RETURN in answer to this question, and
DNS will not be used.
You will also be asked to specify the host that you
want to transfer the sets from and the directory on
that host that the files are in. This directory should
be mountable by the machine you are installing on,
i.e., correctly exported to your machine.
If you did not set up DNS, you will need to specify an
IP address instead of a hostname for the NFS server.
16. Installation from an unmounted file system
In order to install from a local file system, you will
need to specify the device that the file system resides
on (for example wd1e), the type of the file system, and
the directory on the specified file system where the
sets are located. sysinst will then check if it can
indeed access the sets at that location.
17. Installation from a local directory
This option assumes that you have already done some
preparation yourself. The sets should be located in a
directory on a file system that is already accessible.
sysinst will ask you for the name of this directory.
18. Extracting the distribution sets
A progress bar will be displayed while the distribution
sets are being extracted.
After all the files have been extracted, the device
node files will be created. If you have already con-
figured networking, you will be asked if you want to
use this configuration for normal operation. If so,
these values will be installed in the network configu-
ration files.
19. Configure additional items
The next menu will allow you to select a number of
additional items to configure, including the time zone
that you're in, to make sure your clock has the right
offset from UTC, the root user's shell, and the initial
root password.
You can also enable installation of binary packages,
which installs the pkgin(1) tool for managing binary
packages for third-party software. This will feel
familiar to users of package tools such as apt-get or
yum. If you prefer to install third-party software
from source, you can install the pkgsrc(7) tree.
Finally, you can enable some daemons such as sshd(8),
ntpd(8), or mdnsd(8).
20. Finalizing your installation
Congratulations, you have successfully installed NetBSD
9.4. You can now reboot the machine and boot NetBSD
from hard disk.
Post installation steps
Once you've got the operating system running, there are a
few things you need to do in order to bring the system into
a properly configured state. The most important steps are
described below.
1. Before all else, read postinstall(8).
2. Configuring /etc/rc.conf
If you or the installation software haven't done any
configuration of /etc/rc.conf (sysinst normally will),
the system will drop you into single user mode on first
reboot with the message
/etc/rc.conf is not configured. Multiuser boot
aborted.
and with the root file system (/) mounted read-only.
When the system asks you to choose a shell, simply
press RETURN to get to a /bin/sh prompt. If you are
asked for a terminal type, respond with vt220 (or what-
ever is appropriate for your terminal type) and press
RETURN. You may need to type one of the following com-
mands to get your delete key to work properly, depend-
ing on your keyboard:
# stty erase '^h'
# stty erase '^?'
At this point, you need to configure at least one file
in the /etc directory. You will need to mount your
root file system read/write with:
# /sbin/mount -u -w /
Change to the /etc directory and take a look at the
/etc/rc.conf file. Modify it to your tastes, making
sure that you set rc_configured=YES so that your
changes will be enabled and a multi-user boot can pro-
ceed. Default values for the various programs can be
found in /etc/defaults/rc.conf, where some in-line doc-
umentation may be found. More complete documentation
can be found in rc.conf(5).
When you have finished editing /etc/rc.conf, type exit
at the prompt to leave the single-user shell and con-
tinue with the multi-user boot.
Other values that may need to be set in /etc/rc.conf
for a networked environment are hostname and possibly
defaultroute. You may also need to add an ifconfig_int
for your <int> network interface, along the lines of
ifconfig_le0="inet 192.0.2.123 netmask
255.255.255.0"
or, if you have myname.my.dom in /etc/hosts:
ifconfig_le0="inet myname.my.dom netmask
255.255.255.0"
To enable proper hostname resolution, you will also
want to add an /etc/resolv.conf file or (if you are
feeling a little more adventurous) run named(8). See
resolv.conf(5) or named(8) for more information.
Instead of manually configuring networking, DHCP can be
used by setting dhcpcd=YES in /etc/rc.conf.
3. Logging in
After reboot, you can log in as root at the login
prompt. If you didn't set a password in sysinst, there
is no initial password. You should create an account
for yourself (see below) and protect it and the
``root'' account with good passwords. By default, root
login from the network is disabled (even via ssh(1)).
One way to become root over the network is to log in as
a different user that belongs to group ``wheel'' (see
group(5)) and use su(1) to become root.
4. Adding accounts
Use the useradd(8) command to add accounts to your sys-
tem. Do not edit /etc/passwd directly! See vipw(8) and
pwd_mkdb(8) if you want to edit the password database.
5. The X Window System
If you installed the X Window System, you may want to
read the chapter about X in the NetBSD Guide:
https://www.NetBSD.org/docs/guide/en/chap-x.html:
6. Installing third party packages
If you wish to install any of the software freely
available for UNIX-like systems you are strongly
advised to first check the NetBSD package system,
pkgsrc. pkgsrc automatically handles any changes nec-
essary to make the software run on NetBSD. This
includes the retrieval and installation of any other
packages the software may depend upon.
o More information on the package system is available
at
https://www.NetBSD.org/docs/software/packages.html
o A list of available packages suitable for browsing
is at
https://cdn.NetBSD.org/pub/pkgsrc/current/pkgsrc/README.html
o Precompiled binaries can be found at
https://cdn.NetBSD.org/pub/pkgsrc/packages/NetBSD/
usually in the evbppc/9.4/All subdir. If you
installed pkgin(1) in the sysinst post-installation
configuration menu, you can use it to automatically
install binary packages over the network. Assuming
that /usr/pkg/etc/pkgin/repositories.conf is cor-
rectly configured, you can install them with the
following commands:
# pkgin install tcsh
# pkgin install bash
# pkgin install perl
# pkgin install apache
# pkgin install kde
# pkgin install firefox
...
Note: Some mirror sites don't mirror the
/pub/pkgsrc directory.
The above commands will install the Tenex-csh and
Bourne Again shells, the Perl programming language,
Apache web server, KDE desktop environment and the
Firefox web browser as well as all the packages
they depend on.
o If you did not install it from the sysinst post-
installation configuration menu, the pkgsrc(7)
framework for compiling packages can be obtained by
retrieving the file
https://cdn.NetBSD.org/pub/pkgsrc/stable/pkgsrc.tar.gz.
It is typically extracted into /usr/pkgsrc (though
other locations work fine) with the commands:
# cd /usr
# tar -zxpf pkgsrc.tar.gz
After extracting, see the doc/pkgsrc.txt file in
the extraction directory (e.g.,
/usr/pkgsrc/doc/pkgsrc.txt) for more information.
7. Misc
o Edit /etc/mail/aliases to forward root mail to the
right place. Don't forget to run newaliases(1)
afterwards.
o Edit /etc/rc.local to run any local daemons you
use.
o Many of the /etc files are documented in section 5
of the manual; so just invoking
# man 5 filename
is likely to give you more information on these
files.
Upgrading a previously-installed NetBSD System
The easiest way to upgrade to NetBSD 9.4 is with binaries,
and that is the method documented here.
To do the upgrade, you must have one form of boot media
available. You must also have at least the base and kern
binary distribution sets available. Finally, you must have
sufficient disk space available to install the new binaries.
Since files already installed on the system are overwritten
in place, you only need additional free space for files
which weren't previously installed or to account for growth
of the sets between releases.
Since upgrading involves replacing the kernel, boot blocks,
and most of the system binaries, it has the potential to
cause data loss. You are strongly advised to back up any
important data on the NetBSD partition or on another operat-
ing system's partition on your disk before beginning the
upgrade process.
The upgrade procedure is similar to an installation, but
without the hard disk partitioning.
Fetching the binary sets is done in the same manner as the
installation procedure; refer to the installation part of
the document for help. File systems are checked before
unpacking the sets.
After a new kernel has been copied to your hard disk, your
machine is a complete NetBSD 9.4 system. However, that
doesn't mean that you're finished with the upgrade process.
You will probably want to update the set of device nodes you
have in /dev. If you've changed the contents of /dev by
hand, you will need to be careful about this, but if not,
you can just cd into /dev, and run the command:
# sh MAKEDEV all
sysinst will attempt to merge the settings stored in your
/etc directory with the new version of NetBSD using the
postinstall(8) utility. However, postinstall(8) is only
able to deal with changes that are easily automated. It is
recommended that you use the etcupdate(8) tool to merge any
remaining configuration changes.
Compatibility Issues With Previous NetBSD Releases
Users upgrading from previous versions of NetBSD may wish to
bear the following problems and compatibility issues in mind
when upgrading to NetBSD 9.4.
Note that sysinst will automatically invoke
postinstall fix
and thus all issues that are fixed by postinstall by default
will be handled.
A number of things have been removed from the NetBSD 9.4
release. See the ``Components removed from NetBSD'' section
near the beginning of this document for a list.
Using online NetBSD documentation
Documentation is available if you installed the manual dis-
tribution set. Traditionally, the ``man pages'' (documenta-
tion) are denoted by `name(section)'. Some examples of this
are
o intro(1),
o man(1),
o apropos(1),
o passwd(1), and
o passwd(5).
The section numbers group the topics into several cate-
gories, but three are of primary interest: user commands are
in section 1, file formats are in section 5, and administra-
tive information is in section 8.
The man command is used to view the documentation on a
topic, and is started by entering man [section] topic. The
brackets [] around the section should not be entered, but
rather indicate that the section is optional. If you don't
ask for a particular section, the topic with the lowest num-
bered section name will be displayed. For instance, after
logging in, enter
# man passwd
to read the documentation for passwd(1). To view the docu-
mentation for passwd(5), enter
# man 5 passwd
instead.
If you are unsure of what man page you are looking for,
enter
# apropos subject-word
where subject-word is your topic of interest; a list of pos-
sibly related man pages will be displayed.
Administrivia
If you've got something to say, do so! We'd like your
input. There are various mailing lists available via the
mailing list server at
[email protected]. See
https://www.NetBSD.org/mailinglists/
for details.
There are various mailing lists set up to deal with comments
and questions about this release. Please send comments to:
[email protected].
To report bugs, use the send-pr(1) command shipped with
NetBSD, and fill in as much information about the problem as
you can. Good bug reports include lots of details.
Bugs also can be submitted and queried with the web inter-
face at
https://www.NetBSD.org/support/send-pr.html
There are also port-specific mailing lists, to discuss
aspects of each port of NetBSD. Use majordomo to find their
addresses, or visit
https://www.NetBSD.org/mailinglists/
If you're interested in doing a serious amount of work on a
specific port, you probably should contact the `owner' of
that port (listed below).
If you'd like to help with NetBSD, and have an idea as to
how you could be useful, send us mail or subscribe to:
[email protected].
As a favor, please avoid mailing huge documents or files to
these mailing lists. Instead, put the material you would
have sent up for FTP or WWW somewhere, then mail the appro-
priate list about it. If you'd rather not do that, mail the
list saying you'll send the data to those who want it.
Thanks go to
o The former members of UCB's Computer Systems Research
Group, including (but not limited to):
Keith Bostic
Ralph Campbell
Mike Karels
Marshall Kirk McKusick
for their work on BSD systems, support, and encourage-
ment.
o The Internet Systems Consortium, Inc. for hosting the
NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS,
SUP, Rsync and WWW servers.
o The Internet Research Institute in Japan for hosting the
server which runs the CVSweb interface to the NetBSD
source tree.
o The Columbia University Computer Science Department for
hosting the build cluster.
o The many organizations that provide NetBSD mirror sites.
o Without CVS, this project would be impossible to manage,
so our hats go off to Brian Berliner, Jeff Polk, and the
various other people who've had a hand in making CVS a
useful tool.
o We list the individuals and organizations that have made
donations or loans of hardware and/or money, to support
NetBSD development, and deserve credit for it at
https://www.NetBSD.org/donations/
(If you're not on that list and should be, tell us! We
probably were not able to get in touch with you, to ver-
ify that you wanted to be listed.)
o Finally, we thank all of the people who've put sweat and
tears into developing NetBSD since its inception in Jan-
uary, 1993. (Obviously, there are a lot more people who
deserve thanks here. If you're one of them, and would
like to be mentioned, tell us!)
Legal Mumbo-Jumbo
All product names mentioned herein are trademarks or regis-
tered trademarks of their respective owners.
The following notices are required to satisfy the license
terms of the software that we have mentioned in this docu-
ment:
NetBSD is a registered trademark of The NetBSD Foundation,
Inc.
This product includes software developed by the University
of California, Berkeley and its contributors.
This product includes software developed by the NetBSD Foun-
dation.
This product includes software developed by The NetBSD Foun-
dation, Inc. and its contributors.
This product includes software developed for the NetBSD
Project. See
https://www.NetBSD.org/ for information about
NetBSD.
This product includes cryptographic software written by Eric
Young (
[email protected])
This product includes cryptographic software written by Eric
Young (
[email protected])
This product includes software designed by William Allen
Simpson.
This product includes software developed at Ludd, University
of Lulea.
This product includes software developed at Ludd, University
of Lulea, Sweden and its contributors.
This product includes software developed at the Information
Technology Division, US Naval Research Laboratory.
This product includes software developed by Aaron Brown and
Harvard University.
This product includes software developed by Adam Ciarcinski
for the NetBSD project.
This product includes software developed by Adam Glass.
This product includes software developed by Adam Glass and
Charles M. Hannum.
This product includes software developed by Alex Zepeda.
This product includes software developed by Alex Zepeda, and
Colin Wood for the NetBSD Projet.
This product includes software developed by Allen Briggs.
This product includes software developed by Amancio Hasty
and Roger Hardiman
This product includes software developed by Ben Gray.
This product includes software developed by Berkeley Soft-
ware Design, Inc.
This product includes software developed by Bill Paul.
This product includes software developed by Boris Popov.
This product includes software developed by Brini.
This product includes software developed by Bruce M. Simp-
son.
This product includes software developed by Causality Lim-
ited.
This product includes software developed by Charles Hannum.
This product includes software developed by Charles M. Han-
num.
This product includes software developed by Charles M. Han-
num, by the University of Vermont and State Agricultural
College and Garrett A. Wollman, by William F. Jolitz, and
by the University of California, Berkeley, Lawrence Berkeley
Laboratory, and its contributors.
This product includes software developed by Christian E.
Hopps.
This product includes software developed by Christian E.
Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg
and Michael Teske.
This product includes software developed by Christopher G.
Demetriou.
This product includes software developed by Christopher G.
Demetriou for the NetBSD Project.
This product includes software developed by Chuck Silvers.
This product includes software developed by Cisco Systems,
Inc.
This product includes software developed by Colin Wood.
This product includes software developed by Colin Wood for
the NetBSD Project.
This product includes software developed by Computing Ser-
vices at Carnegie Mellon University (
http://www.cmu.edu/com-
puting/).
This product includes software developed by Daan Vreeken.
This product includes software developed by Daishi Kato
This product includes software developed by Daniel Widenfalk
and Michael L. Hitch.
This product includes software developed by Daniel Widenfalk
for the NetBSD Project.
This product includes software developed by David Jones and
Gordon Ross
This product includes software developed by David Miller.
This product includes software developed by Dean Huxley.
This product includes software developed by Emmanuel Dreyfus
This product includes software developed by Eric S. Hvozda.
This product includes software developed by Eric S. Raymond
This product includes software developed by Eric Young
(
[email protected])
This product includes software developed by Eric Young
(
[email protected])
This product includes software developed by Ezra Story.
This product includes software developed by Ezra Story and
by Kari Mettinen.
This product includes software developed by Ezra Story, by
Kari Mettinen and by Bernd Ernesti.
This product includes software developed by Ezra Story, by
Kari Mettinen, and Michael Teske.
This product includes software developed by Ezra Story, by
Kari Mettinen, Michael Teske and by Bernd Ernesti.
This product includes software developed by Frank van der
Linden for the NetBSD Project.
This product includes software developed by Gardner
Buchanan.
This product includes software developed by Garrett D'Amore.
This product includes software developed by Gary Thomas.
This product includes software developed by Gordon Ross
This product includes software developed by Harvard Univer-
sity.
This product includes software developed by Harvard Univer-
sity and its contributors.
This product includes software developed by Hellmuth
Michaelis and Joerg Wunsch
This product includes software developed by Henrik Vester-
gaard Draboel.
This product includes software developed by Herb Peyerl.
This product includes software developed by Hidetoshi
Shimokawa.
This product includes software developed by Hubert Feyrer
for the NetBSD Project.
This product includes software developed by Ian W. Dall.
This product includes software developed by Intel Corpora-
tion and its contributors.
This product includes software developed by Internet Initia-
tive Japan Inc.
This product includes software developed by Internet
Research Institute, Inc.
This product includes software developed by James R. Maynard
III.
This product includes software developed by Jared D.
McNeill.
This product includes software developed by Jason L. Wright
This product includes software developed by Jason R. Thorpe
for And Communications,
http://www.and.com/
This product includes software developed by Joachim Koenig-
Baltes.
This product includes software developed by Jochen Pohl for
The NetBSD Project.
This product includes software developed by Joerg Wunsch
This product includes software developed by John Birrell.
This product includes software developed by John P. Wit-
tkoski.
This product includes software developed by John Polstra.
This product includes software developed by Jonathan R.
Stone for the NetBSD Project.
This product includes software developed by Jonathan Stone.
This product includes software developed by Jonathan Stone
and Jason R. Thorpe for the NetBSD Project.
This product includes software developed by Jonathan Stone
for the NetBSD Project.
This product includes software developed by Julian High-
field.
This product includes software developed by K. Kobayashi
This product includes software developed by K. Kobayashi and
H. Shimokawa
This product includes software developed by Kazuhisa
Shimizu.
This product includes software developed by Kazuki Sakamoto.
This product includes software developed by Kenneth Stailey.
This product includes software developed by Kiyoshi Ikehara.
This product includes software developed by Klaus Burkert,by
Bernd Ernesti, by Michael van Elst, and by the University of
California, Berkeley and its contributors.
This product includes software developed by Kyma Systems.
This product includes software developed by Leo Weppelman
and Waldi Ravens.
This product includes software developed by Lloyd Parkes.
This product includes software developed by Lutz Vieweg.
This product includes software developed by Marc Horowitz.
This product includes software developed by Marcus Comstedt.
This product includes software developed by Mark Brinicombe.
This product includes software developed by Mark Brinicombe
for the NetBSD Project.
This product includes software developed by Mark Tinguely
and Jim Lowe
This product includes software developed by Markus Wild.
This product includes software developed by Marshall M. Mid-
den.
This product includes software developed by Masanobu Saitoh.
This product includes software developed by Masaru Oki.
This product includes software developed by Matt DeBergalis
This product includes software developed by Matthew Fre-
dette.
This product includes software developed by Michael Smith.
This product includes software developed by Microsoft
This product includes software developed by Mika Kortelainen
This product includes software developed by Mike Pritchard.
This product includes software developed by Mike Pritchard
and contributors.
This product includes software developed by Minoura Makoto.
This product includes software developed by MINOURA Makoto,
Takuya Harakawa.
This product includes software developed by Niels Provos.
This product includes software developed by Niklas Hal-
lqvist.
This product includes software developed by Niklas Hal-
lqvist, Brandon Creighton and Job de Haas.
This product includes software developed by Paolo Abeni.
This product includes software developed by Paul Kranenburg.
This product includes software developed by Paul Mackerras.
This product includes software developed by Paul Mackerras
<
[email protected]>.
This product includes software developed by Pedro Roque Mar-
ques <
[email protected]>
This product includes software developed by Per Fogelstrom.
This product includes software developed by Peter Galbavy.
This product includes software developed by Phase One, Inc.
This product includes software developed by Philip A. Nel-
son.
This product includes software developed by QUALCOMM Incor-
porated.
This product includes software developed by RiscBSD.
This product includes software developed by Roar Thronaes.
This product includes software developed by Rodney W.
Grimes.
This product includes software developed by Roger Hardiman
This product includes software developed by Rolf Grossmann.
This product includes software developed by Ross Harvey.
This product includes software developed by Ross Harvey for
the NetBSD Project.
This product includes software developed by Scott Bartram.
This product includes software developed by Scott Stevens.
This product includes software developed by Shingo WATANABE.
This product includes software developed by Softweyr LLC,
the University of California, Berkeley, and its contribu-
tors.
This product includes software developed by Stephan Thesing.
This product includes software developed by Steven M.
Bellovin
This product includes software developed by Takashi Hamada.
This product includes software developed by Takumi Nakamura.
This product includes software developed by Tatoku Ogaito
for the NetBSD Project.
This product includes software developed by Tommi Komulainen
<
[email protected]>.
This product includes software developed by TooLs GmbH.
This product includes software developed by Trimble Naviga-
tion, Ltd.
This product includes software developed by Waldi Ravens.
This product includes software developed by WIDE Project and
its contributors.
This product includes software developed by Winning Strate-
gies, Inc.
This product includes software developed by Yasushi Yamasaki
This product includes software developed by Yen Yen Lim and
North Dakota State University
This product includes software developed by Zembu Labs, Inc.
This product includes software developed by the Alice Group.
This product includes software developed by the Computer
Systems Engineering Group at Lawrence Berkeley Laboratory.
This product includes software developed by the Computer
Systems Laboratory at the University of Utah.
This product includes software developed by the Harvard Uni-
versity and its contributors.
This product includes software developed by the Kungliga
Tekniska Hoegskolan and its contributors.
This product includes software developed by the Network
Research Group at Lawrence Berkeley Laboratory.
This product includes software developed by the OpenSSL
Project for use in the OpenSSL Toolkit.
(
http://www.OpenSSL.org/)
This product includes software developed by the PocketBSD
project and its contributors.
This product includes software developed by the RiscBSD ker-
nel team
This product includes software developed by the RiscBSD
team.
This product includes software developed by the SMCC Tech-
nology Development Group at Sun Microsystems, Inc.
This product includes software developed by the University
of California, Lawrence Berkeley Laboratories.
This product includes software developed by the University
of California, Lawrence Berkeley Laboratory.
This product includes software developed by the University
of California, Lawrence Berkeley Laboratory and its contrib-
utors.
This product includes software developed by the University
of Vermont and State Agricultural College and Garrett A.
Wollman.
This product includes software developed by the University
of Vermont and State Agricultural College and Garrett A.
Wollman, by William F. Jolitz, and by the University of
California, Berkeley, Lawrence Berkeley Laboratory, and its
contributors.
This product includes software developed by the Urbana-Cham-
paign Independent Media Center.
This product includes software developed for the FreeBSD
project
This product includes software developed for the NetBSD
Project by Allegro Networks, Inc., and Wasabi Systems, Inc.
This product includes software developed for the NetBSD
Project by Bernd Ernesti.
This product includes software developed for the NetBSD
Project by Christopher G. Demetriou.
This product includes software developed for the NetBSD
Project by Eiji Kawauchi.
This product includes software developed for the NetBSD
Project by Frank van der Linden
This product includes software developed for the NetBSD
Project by Genetec Corporation.
This product includes software developed for the NetBSD
Project by Jason R. Thorpe.
This product includes software developed for the NetBSD
Project by John M. Vinopal.
This product includes software developed for the NetBSD
Project by Jonathan Stone.
This product includes software developed for the NetBSD
Project by Kyma Systems LLC.
This product includes software developed for the NetBSD
Project by Matthias Drochner.
This product includes software developed for the NetBSD
Project by Perry E. Metzger.
This product includes software developed for the NetBSD
Project by Piermont Information Systems Inc.
This product includes software developed for the NetBSD
Project by Shigeyuki Fukushima.
This product includes software developed for the NetBSD
Project by SUNET, Swedish University Computer Network.
This product includes software developed for the NetBSD
Project by Wasabi Systems, Inc.
This product includes software developed or owned by Caldera
International, Inc.
This product includes software developed under OpenBSD by
Per Fogelstrom.
This product includes software developed under OpenBSD by
Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA.
This software was developed by Holger Veit and Brian Moore
for use with "386BSD" and similar operating systems. "Simi-
lar operating systems" includes mainly non-profit oriented
systems for research and education, including but not
restricted to "NetBSD", "FreeBSD", "Mach" (by CMU).
The Institute of Electrical and Electronics Engineers and
The Open Group, have given us permission to reprint portions
of their documentation.
In the following statement, the phrase ``this text'' refers
to portions of the system documentation.
Portions of this text are reprinted and reproduced in
electronic form in NetBSD, from IEEE Std 1003.1, 2004
Edition, Standard for Information Technology -- Portable
Operating System Interface (POSIX), The Open Group Base
Specifications Issue 6, Copyright (C) 2001-2004 by the
Institute of Electrical and Electronics Engineers, Inc and
The Open Group. In the event of any discrepancy between
these versions and the original IEEE and The Open Group
Standard, the original IEEE and The Open Group Standard is
the referee document.
The original Standard can be obtained online at
http://www.opengroup.org/unix/online.html.
This notice shall appear on any product containing this
material.
In the following statement, "This software" refers to the
parallel port driver:
This software is a component of "386BSD" developed by
William F. Jolitz, TeleMuse.
Some files have the following copyright:
Mach Operating System
Copyright (c) 1991,1990,1989 Carnegie Mellon Univer-
sity
All Rights Reserved.
Permission to use, copy, modify and distribute this
software and its documentation is hereby granted, pro-
vided that both the copyright notice and this permis-
sion notice appear in all copies of the software, de-
rivative works or modified versions, and any portions
thereof, and that both notices appear in supporting
documentation.
CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN
ITS CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABIL-
ITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING
FROM THE USE OF THIS SOFTWARE.
Carnegie Mellon requests users of this software to
return to
Software Distribution Coordinator or Software.Dis-
[email protected]
School of Computer Science
Carnegie Mellon University
Pittsburgh PA 15213-3890
any improvements or extensions that they make and
grant Carnegie the rights to redistribute these
changes.
Some files have the following copyright:
Copyright (c) 1994, 1995 Carnegie-Mellon University.
All rights reserved.
Author: Chris G. Demetriou
Permission to use, copy, modify and distribute this
software and its documentation is hereby granted, pro-
vided that both the copyright notice and this permis-
sion notice appear in all copies of the software, de-
rivative works or modified versions, and any portions
thereof, and that both notices appear in supporting
documentation.
CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN
ITS "AS IS" CONDITION. CARNEGIE MELLON DISCLAIMS ANY
LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER
RESULTING FROM THE USE OF THIS SOFTWARE.
Carnegie Mellon requests users of this software to
return to
Software Distribution Coordinator or Software.Dis-
[email protected]
School of Computer Science
Carnegie Mellon University
Pittsburgh PA 15213-3890
any improvements or extensions that they make and
grant Carnegie the rights to redistribute these
changes.
Some files have the following copyright:
Copyright 1996 The Board of Trustees of The Leland
Stanford Junior University. All Rights Reserved.
Permission to use, copy, modify, and distribute this
software and its documentation for any purpose and
without fee is hereby granted, provided that the above
copyright notice appear in all copies. Stanford Uni-
versity makes no representations about the suitability
of this software for any purpose. It is provided "as
is" without express or implied warranty.
The End
NetBSD/evbppc 9.4 Apr 20, 2024 NetBSD/evbppc 9.4
