HOWTO Use a Compaq Remote Insight Lights Out Edition for a Headless, Remote
Linux Installation
Marc Nozell
Compaq Computer Corporation
�����������
[email protected]
��������
Revision History
Revision v1.0 25 October 2000 Revised by: MN
Initial public release.
This document describes how to install Linux on a headless Compaq ProLiant
server with a Compaq Remote Insight Lights-Out Edition card without physical
access to the system. The installation is done remotely through the use of a
Java-enabled browser.
-----------------------------------------------------------------------------
Table of Contents
1. Introduction
1.1. Trademarks
1.2. Feedback
1.3. Distribution Policy
2. Compaq Remote Insight Lights-Out Background
2.1. Key Features
3. Linux Installation using a Remote Insight Lights-Out
3.1. Hardware Installation
3.2. Setting up a Linux Distribution Point
3.3. Creating a Virtual Floppy Disk
3.4. Downloading a Virtual Floppy Disk to the Server
3.5. Power on and Booting
1. Introduction
This document is a quick guide which shows how to install Linux on a remote,
headless Compaq ProLiant system equipped with a Compaq Remote Insight
Lights-Out Edition card without needing physical access to the system.
This document further describes how to use a virtual floppy disk for the
initial install of Linux, and to setup an Apache server to provide the
distribution media for completing the installation.
-----------------------------------------------------------------------------
1.1. Trademarks
Compaq, Compaq Insight Manager, ProLiant, are registered with the United
States Patent and Trademark office.
Microsoft, Windows, Windows NT are trademarks and/or registered trademarks of
Microsoft Corporation.
Red Hat is a trademark of Red Hat, Inc., in the United States and other
countries.
SuSE is a trademark of SuSE GmbH.
Linux is a registered trademark of Linus Torvalds.
Other product names mentioned herein may be trademarks and/or registered
trademarks of their respective companies.
-----------------------------------------------------------------------------
1.2. Feedback
Feedback will make this HOWTO more useful. If you have any suggestions,
corrections, or comments, send them to
[email protected]
-----------------------------------------------------------------------------
1.3. Distribution Policy
Copyright (c) 2000 Compaq Computer Corporation.
The information in this publication is subject to change without notice and
is provided "AS IS" WITHOUT WARRANTY OF ANY KIND. THE ENTIRE RISK ARISING OUT
OF THE USE OF THIS INFORMATION REMAINS WITH RECIPIENT. IN NO EVENT SHALL
COMPAQ BE LIABLE FOR ANY DIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE
OR OTHER DAMAGES WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS
OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION),
EVEN IF COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
The limited warranties for Compaq products are exclusively set forth in the
documentation accompanying such products. Nothing herein should be construed
as constituting a further or additional warranty.
This publication does not constitute an endorsement of the product or
products that were tested. The configuration or configurations tested or
described may or may not be the only available solution. This test is not a
determination or product quality or correctness, nor does it ensure
compliance with any federal, state, or local requirements.
This document may be distributed under the terms set forth in the LDP license
at [
http://sunsite.unc.edu/LDP/COPYRIGHT.html] sunsite.unc.edu/LDP/
COPYRIGHT.html.
This HOWTO is free documentation; you can redistribute it and/or modify it
under the terms of the Linux Document Project (LDP) license. This document is
distributed in the hope that it will be useful, but without any warranty;
without even the implied warranty of merchantability or fitness for a
particular purpose. See the LDP license for more details.
-----------------------------------------------------------------------------
2. Compaq Remote Insight Lights-Out Background
The Remote Insight Lights-Out is an optional management PCI card with a
dedicated LAN connection. It provides full access and control of servers even
when the server is in a failed state.
-----------------------------------------------------------------------------
2.1. Key Features
The key features of the Remote Insight Lights-Out card:
��*�Self-contained with on-board processor, memory, NIC, and ROM
��*�External power adapter ensures continuous server access
��*�Enables 'headless' server deployments in data centers
��*�Virtual Floppy Drive allows host server to remotely boot from a standard
1.44 MB floppy diskette in a network client, enabling remote OS
installation from a network drive, and remote server ROM updates
��*�Full control of your server with browser-based, virtual graphical remote
console
��*�No additional software required for Compaq ProLiant servers - the client
just requires a browser that supports Java.
��*�Virtual Power Button provides full control of remote server power state -
turn your server on or off remotely
��*�Remote Reboot allows cold reboot when system is not responding.
��*�SSL encryption of HTTP data before transmitting over the network
��*�Dedicated, low-bandwidth network connection provides secure access over
LAN
��*�Group administration for user accounts
To get more information about the Remote Insight Lights-Out Edition see the
Compaq web page at [
http://www.compaq.com/lights-out]
http://www.compaq.com/
lights-out
-----------------------------------------------------------------------------
3. Linux Installation using a Remote Insight Lights-Out
After you have installed the card into the server system you will need to set
up a Linux distribution repository, build and download a special boot floppy,
and drive the installation through a browser.
-----------------------------------------------------------------------------
3.1. Hardware Installation
The first step is to install the Remote Insight Lights-Out Edition card in a
Compaq ProLiant Server and configure it for network access. Using DHCP is the
easiest way to get the Remote Insight Lights-Out card on the network.
-----------------------------------------------------------------------------
3.2. Setting up a Linux Distribution Point
On another server, make the contents of the Red Hat installation CD available
via HTTP or FTP. For this example, the server is named disto.domain.com and
HTTP is used.
Copy the entire CD to the local hard disk and give appropriate file
protections to allow the web server to read it. For Red Hat V6.2, use the
following commands.
# mount -t iso9660 -o ro /dev/cdrom /mnt/cdrom
# mkdir /usr/src/RHCD
# (cd /mnt/cdrom && tar cf - . ) | (cd /usr/src/RHCD && tar xvfp - )
# umount /mnt/cdrom
# chmod +x -R /usr/src/RHCD
RedHat V7.0 contains two binary distribution CDs, so both need to be copied
into the same directory structure. Put the first binary distribution CD into
the drive and as above use the following commands:
# mount -t iso9660 -o ro /dev/cdrom /mnt/cdrom
# mkdir /usr/src/RHCD
# (cd /mnt/cdrom && tar cf - . ) | (cd /usr/src/RHCD && tar xvfp - )
# umount /mnt/cdrom
Then put the second binary distribution CD into the drive and issue the
following commands.
# mount -t iso9660 -o ro /dev/cdrom /mnt/cdrom
# mkdir /usr/src/RHCD
# (cd /mnt/cdrom && tar cf - . ) | (cd /usr/src/RHCD && tar xvfp - )
# umount /mnt/cdrom
# chmod +x -R /usr/src/RHCD
Edit httpd.conf to add the following lines near the section wehre other
Aliases are defined. The location of the configuration file varies. On a
default Red Hat system, it is in /etc/httpd/httpd.conf. If the Apache server
was installed from sources using the default location, it is in /usr/local/
apache/conf/httpd.conf. You can also try locate httpd.conf to find it.
<Directory /usr/src/RHCD/>
Options Indexes
AllowOverride all
</Directory>
Alias /rh /usr/src/RHCD
Restart the Apache server. If you are still running the default Apache
shipped with Red Hat, do this:
# /etc/rc.d/init.d/httpd restart
Other Linux distributions may put the Apache Web Server startup script in a
different place.
The location of of apachectl may vary; find it with locate apachectl. If you
installed the Apache server yourself, you may want to use apachectl. If you
used the Apache default file locations, it would be the following.
# /usr/local/apache/bin/apachectl restart
Verify that the Red Hat content is available:
# lynx
http://distro.domain.com/rh/
-----------------------------------------------------------------------------
3.3. Creating a Virtual Floppy Disk
Create a special Red Hat boot floppy that can perform a network
installation. The file from the Red Hat CD is in images/bootnet.img;in this
example, /usr/src/RHCD/images/bootnet.img or
http://distro.domain.com/images/
bootnet.img. Other distributions can also install across the network using
similar steps.
From a Linux or UNIX system follow these steps. Put a floppy in the drive.
# dd if=/usr/src/RHCD/images/bootnet.img of=/dev/fd0 bs=1440k
Take that special boot floppy to a Microsoft Windows system that has the
CPQIMAGE program to build an IMG file from a floppy to be uploaded to the
Compaq Remote Insight Lights-Out card. This is the only step that requires
the use of a Microsoft platform. The CPQIMAGE program is not available on any
other platform.
The CPQIMAGE program for Microsoft Windows 95/98/NT 4.0/2000 is available for
download from [
http://www.compaq.com/manage/lightsout-downloads.html] http://
www.compaq.com/manage/lightsout-downloads.html. Choose the "Diskette Image
Utility" download.
Build a file named redhat-bootnet.img using that Windows-based application.
Note for multi-system installations, this file can be reused or simply
provided to the customer.
-----------------------------------------------------------------------------
3.4. Downloading a Virtual Floppy Disk to the Server
Now that a special version of the bootnet.img has been created, it needs to
be loaded into the Virtual Floppy Disk on the Remote Insight Lights-Out card.
1. Connect to the Remote Insight Lights-Out card of the Linux system from a
Java-enabled browser (Netscape, MSIE) using the URL
http://XX.XX.XX.XX
where the X's are the IP address assigned to the card. You can use a
Linux system running Netscape or a Windows system running Netscape or
Microsoft Internet Explorer. Just have the redhat-bootnet.img local to
the system running the browser. Note that this special image file is
larger than a regular 1.44MB floppy. Note: You may want to use FTP to
move the file to the system that you will run the browser on.
2. Log in to the Remote Insight Lights-Out card by using a web browser to
connect to the IP address assigned to the card.
3. Select the "Insert Virtual Floppy" from the web interface, link (on left
near the bottom) and load the redhat-bootnet.img file you just created
into the virtual floppy.
Figure 1. Uploading bootnet floppy image
Image of uploading a floppy image to the Virtual Floppy
Uploading a floppy image to the Virtual Floppy
4. Select the "Virtual Floppy Boot Option" of 'Boot Once' in the "Virtual
Floppy Status" section.
Figure 2. Virtual Floppy Boot Once Dialog
Image of Virtual Floppy Options
Image of Virtual Floppy Options
-----------------------------------------------------------------------------
3.5. Power on and Booting
Now the system is ready to be powered. From the browser, click on the
'Virtual Power Button' and power on the server.
1. Turn on the virtual console by selecting 'Frame View' under the "Remote
Console" section. This starts a Java applet that will show you exactly
what is being displayed on the console, for example, the memory self
check, BIOS startup, SCSI probe, etc. If you have a Compaq SmartArray
card, you can click on the button to send an F10 keypress.
Figure 3. BIOS bootup
Image browser showing memory check during BIOS boot
Browser window showing memory check during BIOS boot
2. Enter "text" for a non-GUI installation method at the boot: prompt. The
graphical interface would work also, but it is slower over the network.
3. Follow the Red Hat installation. When it gets to the place where it asks
for where the distribution media location (CDROM, HardDrive, HTTP, NFS,
FTP), select 'HTTP'.
Figure 4. Red Hat bootup
Image of Red Hat install in text mode
Red Hat text-based installation
4. Put the name of the web server with the Red Hat distribution for the
hostname, in this example, distro.domain.com. The directory for this
example is /rh. If you didn't previously specify a DNS server in the TCP/
IP configuration step prior to this, you can use the IP address of the
system serving the distribution.
Figure 5. Red Hat bootup
Image of selecting HTTP based installation
Selecting HTTP based installation
5. Proceed with a normal Red Hat installation.
6. Skip the configuration of the X server when it gets to the X11
configuration step.
If you want to run a graphical interface on your server system, it can be
configured later using Xconfigurator or xf86config. Compaq suggests that
the server resolution be set to 640x480 at 16-bit color depth and mouse
acceleration to be 1x.
7. Proceed with a normal Red Hat installation. Note that there is a 15
minute timeout for the Remote Console, if your Red Hat installation takes
longer than that you may be disconnected from the Remote Console. If this
happens, simply reconnect to the URL
http://XX.XX.XX.XX, where the X's
are the IP address assigned to the card, and continue from where you left
off.
