The Linux Installation HOWTO

The Linux Installation HOWTO

Eric Steven Raymond

[1]Thyrsus Enterprises

[email protected]

This is version 5.0

Copyright � 2000 by Eric S. Raymond

$Date: 2000/08/21 21:04:53 $
Revision History
Revision 5.0 21 August 2000 Revised by: esr
First DocBook version.

This document describes how to obtain and install Linux software. It
is the first document which a new Linux user should read to get
started.
_________________________________________________________________

Table of Contents
1. [2]Introduction

1.1. [3]Purpose of this document
1.2. [4]Other sources of information
1.3. [5]New versions of this document
1.4. [6]Feedback and Corrections

2. [7]Recent Changes
3. [8]The Easiest Option: Buy, Don't Build
4. [9]Before You Begin

4.1. [10]Hardware requirements
4.2. [11]Space requirements and coexistence

5. [12]Time requirements

5.1. [13]Choosing a Linux distribution

6. [14]Installation Overview

6.1. [15]First Installation Steps: The Easy Way
6.2. [16]First Installation Steps: The Hard Way
6.3. [17]Continuing the Installation
6.4. [18]Basic Parts of an Installation Kit

7. [19]Installation In Detail

7.1. [20]Getting prepared for installation
7.2. [21]Creating the boot and root floppies
7.3. [22]Repartitioning your DOS/Windows drives
7.4. [23]Creating partitions for Linux
7.5. [24]Booting the installation disk
7.6. [25]Installing software packages
7.7. [26]After package installations

8. [27]Booting Your New System
9. [28]After Your First Boot

9.1. [29]Beginning System Administratration
9.2. [30]Custom LILO Configuration

10. [31]Administrivia

10.1. [32]Terms of Use
10.2. [33]Acknowledgements
_________________________________________________________________

1. Introduction

1.1. Purpose of this document

Linux is a freely-distributable implementation of Unix for inexpensive
personal machines (it was developed on 386s, and now supports 486,
586, Pentium, PowerPC, Sun Sparc, ARM and DEC Alpha hardware, and even
the IBM System 390 mainframe!). It supports a wide range of software,
including X Windows, Emacs, TCP/IP networking (including SLIP), and
many applications.

This document assumes that you have heard of and know about Linux, and
now want to get it running. It focuses on the Intel base version,
which is the most popular, but much of the advice applies on Power
PCs, Sparcs and Alphas as well.
_________________________________________________________________

1.2. Other sources of information

If you are new to Linux, there are several sources of basic
information about the system. The best place to find these is at the
at [34]Linux Documentation Project home page. You can find the
[35]latest version of this document there.

You should probably start by browsing the resources under General
Linux Information; the [36]Linux INFO-SHEET and the Linux
[37]META-FAQ. The `Linux Frequently Asked Questions' document contains
many common questions (and answers!) about Linux -- it is a ``must
read'' for new users.

You can find help for common problems on the USENET newsgroups
comp.os.linux.help and comp.os.linux.announce.

The Linux Documentation Project is writing a set of manuals and books
about Linux, all of which are freely distributable on the net and
available from the LDP home page.

The book ``Linux Installation and Getting Started'' is a complete
guide to getting and installing Linux, as well as how to use the
system once you've installed it. It contains a complete tutorial to
using and running the system, and much more information than is
contained here. You can browse it, or download a copy, from the LDP
home page.

Finally, there is a rather technical [38]Guide to x86 Bootstrapping.
This document is NetBSD- rather than Linux-oriented, but contains
useful material on disk configuration and boot managers for multi-OS
setups.

Please do not email me asking for installation help. Even if I had the
time to handle such requests, troubleshooting by mail is much less
efficient than asking help from your local Linux user's group. You can
find worldwide contact information for Linux user groups on the
[39]LDP site.
_________________________________________________________________

1.3. New versions of this document

New versions of the Linux Installation HOWTO will be periodically
posted to comp.os.linux.help and comp.os.linux.announce and
news.answers. They will also be uploaded to various Linux WWW and FTP
sites, including the LDP home page.

You can also view the latest version of this on the World Wide Web via
the URL [40]http://www.linuxdoc.org/HOWTO/Installation-HOWTO.html.
_________________________________________________________________

1.4. Feedback and Corrections

If you have questions or comments about this document, please feel
free to mail Eric S. Raymond, at <[41][email protected]>. I welcome any
suggestions or criticisms. If you find a mistake with this document,
please let me know so I can correct it in the next version. Thanks.

Please do not mail me questions about how to solve hardware problems
encountered during installation. Consult Linux Installation and
Getting Started, bug your vendor, or consult the Linux newsgroup
comp.os.linux.setup. This HOWTO is intended to be rapid, painless
guide to normal installation -- a separate HOWTO on hardware problems
and diagnosis is in preparation.
_________________________________________________________________

2. Recent Changes

* Added the `Buy, Don't Build' section.
* Added the material on booting from CD-ROM.
_________________________________________________________________

3. The Easiest Option: Buy, Don't Build

Linux has now matured enough that there are now system integrators who
will assemble a workstation for you, install and configure a Linux,
and do an intensive burn-in to test it before it's shipped to you. If
you have more money than time, or you have stringent reliability or
performance requirements, these integrators provide a valuable service
by making sure you won't get hardware that's flaky or dies two days
out of the box.

There are several firms of this kind (and I'll list them here as I
learn more about them). The only such outfit I know about personally
is [42]VA Linux Systems; in 1998 I became a member of VA's Board of
Directors. VA builds high-end, high quality Linux workstations with a
nifty Tux-the-penguin logo on the front. They have intimate ties to
the Linux community; SourceForge, the GNU site, and the Debian project
all live on a machine in their back room, and Linus's personal machine
is one of their boxes.

For those of us without a champagne budget, the rest of this HOWTO is
about how to install Linux yourself.
_________________________________________________________________

4. Before You Begin

Before you can install Linux, you'll need to be sure your machine is
Linux-capable, and choose a Linux to install. The [43]Linux
Pre-installation checklist may help you organize configuration data
before you begin.
_________________________________________________________________

4.1. Hardware requirements

What kind of system is needed to run Linux? This is a good question;
the actual hardware requirements for the system change periodically.
The [44]Linux Hardware-HOWTO, gives a (more or less) complete listing
of hardware supported by Linux. The [45]Linux INFO-SHEET, provides
another list.

For the Intel versions, a hardware configuration that looks like the
following is required:

Any 80386, 80486, Pentium or Pentium II processor will do. Non-Intel
clones of the 80386 and up will generally work. You do not need a math
coprocessor, although it is nice to have one.

The ISA, EISA, VESA Local Bus and PCI bus architectures are supported.
The MCA bus architecture (found on IBM PS/2 machines) has been
minimally supported since the 2.1.x kernels, but may not be ready for
prime time yet.

You need at least 4 megabytes of memory in your machine. Technically,
Linux will run with only 2 megs, but most installations and software
require 4. The more memory you have, the happier you'll be. I suggest
an absolute minimum of 16 megabytes if you're planning to use
X-Windows; 64 is better.

Of course, you'll need a hard drive and an AT-standard drive
controller. All MFM, RLL, and IDE drives and controllers should work.
Many SCSI drives and adaptors are supported as well; the Linux
SCSI-HOWTO contains more information on SCSI. If you are assembling a
system from scratch to run Linux, the small additional cost of SCSI is
well worth it for the extra performance and reliability it brings.

You will need a 3.5" floppy drive. While 5.25" floppies are supported
under Linux, they are little-enough used that you should not count on
disk images necessarily fitting on them. (A stripped-down Linux can
actually run on a single floppy, but that's only useful for
installation and certain troubleshooting tasks.)

You also need an MDA, Hercules, CGA, EGA, VGA, or Super VGA video card
and monitor. In general, if your video card and monitor work under
MS-DOS then it should work under Linux. However, if you wish to run
the X window system, there are other restrictions on the supported
video hardware. The [46]Linux XFree86-HOWTO, contains more information
about running X and its requirements.

You'll want a CD-ROM drive. If it's ATAPI, SCSI, or true IDE you
should have no problem making it work (but watch for cheap drives
advertising "IDE" interfaces that aren't true IDE). If your CD-ROM
uses a proprietary interface card, it's possible the installation
kernel you're going to boot from floppy won't be able to see it -- and
an inaccessible CD-ROM is a installation show-stopper. Also, CD-ROMs
that attach to your parallel port won't work at all. If you're in
doubt, consult the [47]Linux CD-ROM HOWTO for a list and details of
supported hardware.

So-called "Plug'n'Play" jumperless cards can be a problem. Support for
these is under active development, but not there yet in the 2.0.25
kernel. Fortunately this is only likely to be a problem with sound or
Ethernet cards.

If you're running on a box that uses one of the Motorola 68K
processors (including Amiga, Atari, or VMEbus machines), see the
[48]Linux/m68k FAQ for information on minimum requirements and the
state of the port. The FAQ now says m68k Linux is as stable and usable
as the Intel versions.
_________________________________________________________________

4.2. Space requirements and coexistence

You'll need free space for Linux on your hard drive. The amount of
space needed depends on how much software you plan to install. Today
most installations require somewhere in the ballpark of a gigabyte of
space. This includes space for the software, swap space (used as
virtual RAM on your machine), and free space for users, and so on.

It's conceivable that you could run a minimal Linux system in 80 megs
or less (this used to be common when Linux distributions were
smaller), and it's conceivable that you could use two gigabytes or
more for all of your Linux software. The amount varies greatly
depending on the amount of software you install and how much space you
require. More about this later.

Linux will co-exist with other operating systems, such as MS-DOS,
Microsoft Windows, or OS/2, on your hard drive. (In fact you can even
access MS-DOS files and run some MS-DOS programs from Linux.) In other
words, when partitioning your drive for Linux, MS-DOS or OS/2 live on
their own partitions, and Linux exists on its own. We'll go into more
detail about such ``dual-boot'' systems later.

You do not need to be running MS-DOS, OS/2, or any other operating
system to use Linux. Linux is a completely different, stand-alone
operating system and does not rely on other OSs for installation and
use.

In all, the minimal setup for Linux is not much more than is required
for most MS-DOS or Windows 3.1 systems sold today (and it's a good
deal less than the minimum for Windows 95!). If you have a 386 or 486
with at least 4 megs of RAM, then you'll be happy running Linux. Linux
does not require huge amounts of diskspace, memory, or processor
speed. Matt Welsh, the originator of this HOWTO, used to run Linux on
a 386/16 MHz (the slowest machine you can get) with 4 megs of RAM, and
was quite happy. The more you want to do, the more memory (and faster
processor) you'll need. In our experience a 486 with 16 megabytes of
RAM running Linux outdoes several models of expensive workstations.
_________________________________________________________________

5. Time requirements

Start to finish, a modern Linux installation from CD-ROM can be
expected to take from ninety minutes to three hours.
_________________________________________________________________

5.1. Choosing a Linux distribution

Before you can install Linux, you need to decide on one of the
``distributions'' of Linux which are available. There is no single,
standard release of the Linux software---there are many such releases.
Each release has its own documentation and installation instructions.

Linux distributions are available both via anonymous FTP and via mail
order on diskette, tape, and CD-ROM. The [49]The Linux Distribution
HOWTO includes descriptions of many Linux distributions available via
FTP and mail order.

In the dim and ancient past when this HOWTO was first written
(1992-93), most people got Linux by tortuous means involving long
downloads off the Internet or a BBS onto their DOS machines, followed
by an elaborate procedure which transferred the downloads onto
multiple floppy disks. One of these disks would then be booted and
used to install the other dozen. With luck (and no media failures)
you'd finish your installation many hours later with a working Linux.
Or maybe not.

While this path is still possible (and you can download any one of
several distributions from [50]Metalab), there are now much less
strenuous ways. The easiest is to buy one of the high-quality
commercial Linux distributions distributed on CD-ROM, such as Red Hat,
Debian, Linux Pro, or WGS. These are typically available for less than
$50 at your local bookstore or computer shop, and will save you many
hours of aggravation.

You can also buy anthology CD-ROMs such as the InfoMagic Linux
Developer's Resource set. These typically include several Linux
distributions and a recent dump of major Linux archive sites, such as
metalab or tsx-11.

In the remainder of this HOWTO we will focus on the steps needed to
install from an anthology CD-ROM, or one of the lower-end commercial
Linuxes that doesn't include a printed installation manual. If your
Linux includes a paper manual some of this HOWTO may provide useful
background, but you should consult the manual for detailed
installation instructions.
_________________________________________________________________

6. Installation Overview

It's wise to collect configuration information on your hardware before
installing. Know the vendor and model number of each card in your
machine; collect the IRQs and DMA channel numbers. You probably won't
need this information -- but if it turns out you do, you'll need it
very badly.

If you want to run a "dual-boot" system (Linux and DOS or Windows or
both), rearrange (repartition) your disk to make room for Linux. If
you're wise, you'll back up everything first!.
_________________________________________________________________

6.1. First Installation Steps: The Easy Way

If you have an EIDE/ATAPI CDROM (normal these days), check your
machine's BIOS settings to see if it has the capability to boot from
CD-ROM. Most machines made after mid-1997 can do this.

If yours is among them, change the settings so that the CD-ROM is
checked first. This is often in a 'BIOS FEATURES' submenu of the BIOS
configuration menus.

Then insert the installation CD-ROM. Reboot. You're started.

If you have a SCSI CDROM you can often still boot from it, but it gets
a little more motherboard/BIOS dependent. Those who know enough to
spend the extra dollars on a SCSI CDROM drive probably know enough to
figure it out.
_________________________________________________________________

6.2. First Installation Steps: The Hard Way

* Make installation floppies.
* Boot an installation mini-Linux from the floppies in order to get
access to the CD-ROM.
_________________________________________________________________

6.3. Continuing the Installation

* Prepare the Linux filesystems. (If you didn't edit the disk
partition table earlier, you will at this stage.)
* Install a basic production Linux from the CD-ROM.
* Boot Linux from the hard drive.
* (Optional) Install more packages from CD-ROM.
_________________________________________________________________

6.4. Basic Parts of an Installation Kit

Here are the basic parts of an installable distribution:

* The README and FAQ files. These will usually be located in the
top-level directory of your CD-ROM and be readable once the CD-ROM
has been mounted under Linux. (Depending on how the CD-ROM was
generated, they may even be visible under DOS/Windows.) It is a
good idea to read these files as soon as you have access to them,
to become aware of important updates or changes.
* A number of bootdisk images (often in a subdirectory). If your
CD-ROM is not bootable, one of these is the file that you will
write to a floppy to create the boot disk. You'll select one of
the above bootdisk images, depending on the type of hardware that
you have in your system.

The issue here is that some hardware drivers conflict with each other
in strange ways, and instead of attempting to debug hardware problems
on your system it's easier to use a boot floppy image with only the
drivers you need enabled. (This will have the nice side effect of
making your kernel smaller.)

* A rescue disk image. This is a disk containing a basic kernel and
tools for disaster recovery in case something trashes the kernel
or boot block of your hard disk.
* RAWRITE.EXE. This is an MS-DOS program that will write the
contents of a file (such as a bootdisk image) directly to a
floppy, without regard to format.

You only need RAWRITE.EXE if you plan to create your boot and root
floppies from an MS-DOS system. If you have access to a UNIX
workstation with a floppy drive instead, you can create the floppies
from there, using the `dd' command, or possibly a vendor-provided
build script. See the man page for dd(1) and ask your local UNIX gurus
for assistance. There's a dd example later in this document.

* The CD-ROM itself. The purpose of the boot disk is to get your
machine ready to load the root or installation disks, which in
turn are just devices for preparing your hard disk and copying
portions of the CD-ROM to it. If your CD-ROM is bootable, you can
boot it and skip right to preparing your disk.
_________________________________________________________________

7. Installation In Detail

7.1. Getting prepared for installation

Linux makes more effective use of PC hardware than MS-DOS, Windows or
NT, and is accordingly less tolerant of misconfigured hardware. There
are a few things you can do before you start that will lessen your
chances of being stopped by this kind of problem.

First, collect any manuals you have on your hardware -- motherboard,
video card, monitor, modem, etc. -- and put them within easy reach.

Second, gather detailed information on your hardware configuration.
One easy way to do this, if you're running MS-DOS 5.0, or up, is to
print a report from the Microsoft diagnostic utility msd.exe (you can
leave out the TSR, driver, memory-map, environment-strings and
OS-version parts). Among other things, this will guarantee you full
and correct information on your video card and mouse type, which will
be helpful in configuring X later on.

Third, check your machine for configuration problems with supported
hardware that could cause an un-recoverable lockup during Linux
installation.

* It is possible for a DOS/Windows system using IDE hard drive(s)
and CD ROM to be functional even with the master/slave jumpers on
the drives incorrectly set. Linux won't fly this way. If in doubt,
check your master-slave jumpers!
* Is any of your peripheral hardware designed with neither
configuration jumpers nor non-volatile configuration memory? If
so, it may require boot-time initialization via an MS-DOS utility
to start up, and may not be easily accessible from Linux. CD-ROMs,
sound cards, Ethernet cards and low-end tape drives can have this
problem. If so, you may be able to work around this with an
argument to the boot prompt; see the[51]Linux Boot Prompt HOWTO
for details).
* Some other operating systems will allow a bus mouse to share an
IRQ with other devices. Linux doesn't support this; in fact,
trying it may lock up your machine. If you are using a bus mouse,
see the [52]Linux Bus Mouse HOWTO, for details.

If possible, get the telephone number of an experienced Linux user you
can call in case of emergency. Nine times out of ten you won't need
it, but it's comforting to have.

Budget time for installation. That will be about one hour on a bare
system or one being converted to all-Linux operation. Or up to three
hours for a dual-boot system (they have a much higher incidence of
false starts and hangups).
_________________________________________________________________

7.2. Creating the boot and root floppies

(This step is only needed if you can't boot from a CD-ROM.)

Your Linux CD-ROM may come with installation aids that will take you
through the process of building boot, root, and rescue disks with
interactive prompts. These may be an MS-DOS installation program (such
as the Red Hat redhat.exe program) or a Unix script, or both.

If you have such a program and can use it, you should read the rest of
this subsection for information only. Run the program to do actual
installation -- its authors certainly knew more about the specific
distribution than I, and you'll avoid many error-prone hand-entry
steps.

More detailed information on making bootdisks, see the [53]Linux
Bootdisk HOWTO.

Your first step will be to select a boot-disk image to fit your
hardware. If you must do this by hand, you'll generally find that
either (a) the bootdisk images on your CD-ROM are named in a way that
will help you pick a correct one, or (b) there's an index file nearby
describing each image.

Next, you must create floppies from the bootdisk image you selected,
and optionally from the rescue disk images. This is where the MS-DOS
program RAWRITE.EXE comes into play.

Next, you must have two or three high-density MS-DOS formatted
floppies. (They must be of the same type; that is, if your boot floppy
drive is a 3.5" drive, both floppies must be high-density 3.5" disks.)
You will use RAWRITE.EXE to write the bootdisk images to the floppies.

Invoke it with no arguments, like this:
C:\> RAWRITE

Answer the prompts for the name of the file to write and the floppy to
write it to (such as A:). RAWRITE will copy the file, block-by-block,
directly to the floppy. Also use RAWRITE for the root disk image (such
as COLOR144). When you're done, you'll have two floppies: one
containing the boot disk, the other containing the root disk. Note
that these two floppies will no longer be readable by MS-DOS (they are
``Linux format'' floppies, in some sense).

You can use the dd(1) commands on a UNIX system to do the same job.
(For this, you will need a UNIX workstation with a floppy drive, of
course.) For example, on a Sun workstation with the floppy drive on
device /dev/rfd0, you can use the command:
$ dd if=bare of=/dev/rfd0 obs=18k

You must provide the appropriate output block size argument (the `obs'
argument) on some workstations (e.g., Suns) or this will fail. If you
have problems the man page for dd(1) may be be instructive.

Be sure that you're using brand-new, error-free floppies. The floppies
must have no bad blocks on them.

Note that you do not need to be running Linux or MS-DOS in order to
install Linux. However, running Linux or MS-DOS makes it easier to
create the boot and root floppies from your CD-ROM. If you don't have
an operating system on your machine, you can use someone else's Linux
or MS-DOS just to create the floppies, and install from there.
_________________________________________________________________

7.3. Repartitioning your DOS/Windows drives

On most used systems, the hard drive is already dedicated to
partitions for MS-DOS, OS/2, and so on. You'll need to resize these
partitions in order to make space for Linux. If you're going to run a
dual-boot system, it's strongly recommended that you read one or more
of the following mini-HOWTOS, which describe different dual-boot
configurations.

* [54]The DOS-Win95-OS2-Linux mini-HOWTO.
* [55]The Linux+Win95 mini-HOWTO.
* [56]The Linux+NT-Loader mini-HOWTO

Even if they are not directly applicable to your system, they will
help you understand the issues involved.

Note: Some Linuxes will install to a directory on your MS-DOS
partition. (This is different than installing from an MS-DOS
partition.) Instead, you use the ``UMSDOS filesystem'', which
allows you to treat a directory of your MS-DOS partition as a Linux
filesystem. In this way, you don't have to repartition your drive.

I only suggest using this method if your drive already has four
partitions (the maximum supported by DOS) and repartitioning would be
more trouble than it's worth (it slows down your Linux due to filename
translation overhead). Or, if you want to try out Linux before
repartitioning, this is a good way to do so. But in most cases you
should re-partition, as described here. If you do plan to use UMSDOS,
you are on your own -- it is not documented in detail here. From now
on, we assume that you are NOT using UMSDOS, and that you will be
repartitioning.

A partition is just a section of the hard drive set aside for a
particular operating system to use. If you only have MS-DOS installed,
your hard drive probably has just one partition, entirely for MS-DOS.
To use Linux, however, you'll need to repartition the drive, so that
you have one partition for MS-DOS, and one (or more) for Linux.

Partitions come in three flavors: primary, extended, and logical.
Briefly, primary partitions are one of the four main partitions on
your drive. However, if you wish to have more than four partitions per
drive, you need to replace the last primary partition with an extended
partition, which can contain many logical partitions. You don't store
data directly on an extended partition---it is used only as a
container for logical partitions. Data is stored only on either
primary or logical partitions.

To put this another way, most people use only primary partitions.
However, if you need more than four partitions on a drive, you create
an extended partition. Logical partitions are then created on top of
the extended partition, and there you have it---more than four
partitions per drive.

Note that you can easily install Linux on the second drive on your
system (known as D: to MS-DOS). You simply specify the appropriate
device name when creating Linux partitions. This is described in
detail below.

Back to repartitioning your drive. It used to be that there was no way
to resize partitions without destroying the data on them. Nowadays
there are partitioning utilities that can resize non-destructively;
they know about the structure of file systems, can find the free space
on a file system, and can move file data around on the partition to
move free space where it needs to be in order for a resize to work
properly. It's still suggested that you make a full backup before
using one of these, in case of program or human error.

Under Linux [57]GNU parted allows you to create, destroy, resize and
copy partitions. It supports ext2, FAT16, and FAT32 filesystems, Linux
swap devices; it also knows about MS-DOS disk labels. Parted is useful
for creating space for new operating systems, reorganising disk usage,
copying data between hard disks, and disk imaging. It is relatively
new code, but is reported to work well and not trash data.

There is a non-destructive disk repartitioner available for MS-DOS,
called [58]FIPS. With FIPS, a disk optimizer (such as Norton Speed
Disk), and a little bit of luck, you should be able to resize MS-DOS
partitions without destroying the data on them.

The older method of resizing a partition, if you don't have one of
these resizing partition editors available, is to delete the
partition(s), and re-create them with smaller sizes. If you use this
method, you absolutely must make a backup in order to save any of your
data.

The classic way to modify partitions is with the program FDISK. For
example, let's say that you have an 80 meg hard drive, dedicated to
MS-DOS. You'd like to split it in half---40 megs for MS-DOS and 40
megs for Linux. In order to do this, you run FDISK under MS-DOS,
delete the 80 meg MS-DOS partition, and re-create a 40 meg MS-DOS
partition in its place. You can then format the new partition and
reinstall your MS-DOS software from backups. 40 megabytes of the drive
is left empty. Later, you create Linux partitions on the unused
portion of the drive.

In short, you should do the following to resize MS-DOS partitions with
FDISK:

1. Make a full backup of your system.
2. Create an MS-DOS bootable floppy, using a command such as

FORMAT /S A:

Copy the files FDISK.EXE and FORMAT.COM to this floppy, as well as
any other utilities that you need. (For example, utilities to
recover your system from backup.)
3. Boot the MS-DOS system floppy.
4. Run FDISK, possibly specifying the drive to modify (such as C: or
D:).
5. Use the FDISK menu options to delete the partitions which you wish
to resize. This will destroy all data on the affected partitions.
6. Use the FDISK menu options to re-create those partitions, with
smaller sizes.
7. Exit FDISK and re-format the new partitions with the FORMAT
command.
8. Restore the original files from backup.

Note that MS-DOS FDISK will give you an option to create a ``logical
DOS drive''. A logical DOS drive is just a logical partition on your
hard drive. You can install Linux on a logical partition, but you
don't want to create that logical partition with MS-DOS fdisk. So, if
you're currently using a logical DOS drive, and want to install Linux
in its place, you should delete the logical drive with MS-DOS FDISK,
and (later) create a logical partition for Linux in its place.

The mechanism used to repartition for OS/2 and other operating systems
is similar. See the documentation for those operating systems for
details.
_________________________________________________________________

7.4. Creating partitions for Linux

After repartitioning your drive, you need to create partitions for
Linux. Before describing how to do that, we'll talk about partitions
and filesystems under Linux.
_________________________________________________________________

7.4.1. Partition basics

Linux requires at least one partition, for the root filesystem, which
will hold the Linux kernel itself.

You can think of a filesystem as a partition formatted for Linux.
Filesystems are used to hold files. Every system must have a root
filesystem, at least. However, many users prefer to use multiple
filesystems---one for each major part of the directory tree. For
example, you may wish to create a separate filesystem to hold all
files under the /usr directory. (Note that on UNIX systems, forward
slashes are used to delimit directories, not backslashes as with
MS-DOS.) In this case you have both a root filesystem, and a /usr
filesystem.

Each filesystem requires its own partition. Therefore, if you're using
both root and /usr filesystems, you'll need to create two Linux
partitions.

In addition, most users create a swap partition, which is used for
virtual RAM. If you have, say, 4 megabytes of memory on your machine,
and a 10-megabyte swap partition, as far as Linux is concerned you
have 14 megabytes of virtual memory.

When using swap space, Linux moves unused pages of memory out to disk,
allowing you to run more applications at once on your system. However,
because swapping is often slow, it's no replacement for real physical
RAM. But applications that require a great deal of memory (such as the
X window system) often rely on swap space if you don't have enough
physical RAM.

Nearly all Linux users employ a swap partition. If you have 4
megabytes of RAM or less, a swap partition is required to install the
software. It is strongly recommended that you have a swap partition
anyway, unless you have a great amount of physical RAM.

The size of your swap partition depends on how much virtual memory you
need. It's often suggested that you have at least 16 megabytes of
virtual memory total. Therefore, if you have 8 megs of physical RAM,
you might want to create an 8-megabyte swap partition. Note that swap
partitions can be no larger than 128 megabytes in size. Therefore, if
you need more than 128 megs of swap, you must create multiple swap
partitions. You may have up to 16 swap partitions in all.

You can find more on the theory of swap space layout and disk
partitioning in the Linux Partition mini-HOWTO
([59]http://www.linuxdoc.org/HOWTO/mini/Partition.html).

Note: it is possible, though a bit tricky, to share swap partitions
between Linux and Windows 95 in a dual-boot system. For details, see
the [60]Linux Swap Space Mini-HOWTO.

Gotcha #1: If you have an EIDE drive with a partition that goes above
504MB, your BIOS may not allow you to boot to a Linux installed there.
So keep your root partition below 504MB. This shouldn't be a problem
for SCSI drive controllers, which normally have their own drive BIOS
firmware. For technical details, see the [61]Large Disk Mini-HOWTO.

Gotcha #2: Are you mixing IDE and SCSI drives? Then watch out. Your
BIOS may not allow you to boot directly to a SCSI drive.
_________________________________________________________________

7.4.2. Sizing partitions

Besides your root and swap partitions, you'll want to set up one or
more partitions to hold your software and home directories.

While, in theory, you could run everything off a single huge root
partition, almost nobody does this. Having multiple partitions has
several advantages:

* It often cuts down the time required for boot-time file-system
checks.
* Files can't grow across partition boundaries. Therefore you can
use partition boundaries as firebreaks against programs (like
Usenet news) that want to eat huge amounts of disk, to prevent
them from crowding out file space needed by your kernel and the
rest of your applications.
* If you ever develop a bad spot on your disk, formatting and
restoring a single partition is less painful than having to redo
everything from scratch.

On today's large disks, a good basic setup is to have a small root
partition (less than 80 meg), a medium-sized /usr partition (up to 300
meg or so) to hold system software, and a /home partition occupying
the rest of your available space for home directories.

You can get more elaborate. If you know you're going to run Usenet
news, for example, you may want to give it a partition of its own to
control its maximum possible disk usage. Or create a /var partition
for mail, news, and temporary files all together. But in today's
regime of very cheap, very large hard disks these complications seem
less and less necessary for your first Linux installation. For your
first time, especially, keep it simple.
_________________________________________________________________

7.5. Booting the installation disk

The first step is to boot the bootdisk you generated. Normally you'll
be able to boot hands-off; the boot kernel prompt will fill itself in
after 10 seconds. This is how you'll normally boot from an IDE disk.

What's actually happening here is this: the boot disk provides a
miniature operating system which (because the hard drive isn't
prepared) uses a portion of your RAM as a virtual disk (called,
logically enough, a `ramdisk').

The boot disk loads onto the ramdisk a small set of files and
installation tools which you'll use to prepare your hard drive and
install a production Linux on it from your CD-ROM.

(In times past this was a two-stage-process, involving a second disk
called a `root disk'; this changed when kernel modules were
introduced.)

By giving arguments after the kernel name, you can specify various
hardware parameters, such as your SCSI controller IRQ and address, or
drive geometry, before booting the Linux kernel. This may be necessary
if Linux does not detect your SCSI controller or hard drive geometry,
for example.

In particular, many BIOS-less SCSI controllers require you to specify
the port address and IRQ at boot time. Likewise, IBM PS/1, ThinkPad,
and ValuePoint machines do not store drive geometry in the CMOS, and
you must specify it at boot time. (Later on, you'll be able to
configure your production system to supply such parameters itself.)

Watch the messages as the system boots. They will list and describe
the hardware your installation Linux detects. In particular, if you
have a SCSI controller, you should see a listing of the SCSI hosts
detected. If you see the message
SCSI: 0 hosts

Then your SCSI controller was not detected, and you will have to
figure out how to tell the kernel where it is.

Also, the system will display information on the drive partitions and
devices detected. If any of this information is incorrect or missing,
you will have to force hardware detection.

On the other hand, if all goes well and your hardware seems to be
detected, you can skip to the following section, ``Loading the root
disk.''

To force hardware detection, you must enter the appropriate parameters
at the boot prompt, using the following syntax:
linux <parameters...>

There are a number of such parameters available; we list some of the
most common below. Modern Linux boot disks will often give you the
option to look at help screen describing kernel parameters before you
boot.

* hd=cylinders,heads,sectors Specify the drive geometry. Required
for systems such as the IBM PS/1, ValuePoint, and ThinkPad. For
example, if your drive has 683 cylinders, 16 heads, and 32 sectors
per track, enter

linux hd=683,16,32

tmc8xx=memaddr,irq Specify address and IRQ for BIOS-less Future
Domain TMC-8xx SCSI controller. For example,

linux tmc8xx=0xca000,5

Note that the 0x prefix must be used for all values given in hex.
This is true for all of the following options.
* st0x=memaddr,irq Specify address and IRQ for BIOS-less Seagate
ST02 controller.
* t128=memaddr,irq Specify address and IRQ for BIOS-less Trantor
T128B controller.
* ncr5380=port,irq,dma Specify port, IRQ, and DMA channel for
generic NCR5380 controller.
* aha152x=port,irq,scsi_id,1 Specify port, IRQ, and SCSI ID for
BIOS-less AIC-6260 controllers. This includes Adaptec 1510, 152x,
and Soundblaster-SCSI controllers.

If you have questions about these boot-time options, please read the
Linux SCSI HOWTO, which should be available on any Linux FTP archive
site (or from wherever you obtained this document). The SCSI HOWTO
explains Linux SCSI compatibility in much more detail.
_________________________________________________________________

7.5.1. Choosing EGA or X installation

Older Linuxes (including Slackware) gave you a shell at this point and
required you to enter installation commands by hand in a prescribed
sequence. This is still possible, but newer ones start by running a
screen-oriented installation program which tries to interactively walk
you through these steps, giving lots of help.

You will probably get the option to try to configure X right away so
the installation program can go graphical. If you choose this route,
the installation program will quiz you about your mouse and monitor
type before getting to the installation proper. Once you get your
production Linux installed, these settings will be saved for you. You
will be able to tune your monitor's performance later, so at this
stage it makes sense to settle for a basic 640x480 SVGA mode.

X isn't necessary for installation, but (assuming you can get past the
mouse and monitor configuration) many people find the graphical
interface easier to use. And you're going to want to bring up X
anyway, so trying it early makes some sense.

Just follow the prompts in the program. It will take you through the
steps necessary to prepare your disk, create initial user accounts,
and install software packages off the CD-ROM.

In the following subsections we'll describe some of the tricky areas
in the installation sequence as if you were doing them by hand. This
should help you understand what the installation program is doing, and
why.
_________________________________________________________________

7.5.2. Using fdisk and cfdisk

Your first installation step once the root-disk Linux is booted will
be to create or edit the partition tables on your disks. Even if you
used FDISK to set up partitions earlier, you'll need to go back to the
partition table now and insert some Linux-specific information now.

To create or edit Linux partitions, we'll use the Linux version of the
fdisk program, or its screen-oriented sibling cfdisk.

Generally the installation program will look for a preexisting
partition table and offer to run fdisk or cfdisk on it for you. Of the
two, cfdisk is definitely easier to use, but current versions of it
are also less tolerant of a nonexistent or garbled partition table.

Therefore you may find (especially if you're installing on virgin
hardware) that you need to start with fdisk to get to a state that
cfdisk can deal with. Try running cfdisk; if it complains, run fdisk.
(A good way to proceed if you're building an all-Linux system and
cfdisk complains is to use fdisk to delete all the existing partions
and then fire up cfdisk to edit the empty table.)

A few notes apply to both fdisk and cfdisk. Both take an argument
which is the name of the drive that you wish to create Linux
partitions on. Hard drive device names are:

* /dev/hda First IDE drive
* /dev/hdb Second IDE drive
* /dev/sda First SCSI drive
* /dev/sdb Second SCSI drive

For example, to create Linux partitions on the first SCSI drive in
your system, you will use (or your installation program might generate
from a menu choice) the command:
cfdisk /dev/sda

If you use fdisk or cfdisk without an argument, it will assume
/dev/hda.

To create Linux partitions on the second drive on your system, simply
specify either /dev/hdb (for IDE drives) or /dev/sdb (for SCSI drives)
when running fdisk.

Your Linux partitions don't all have to be on the same drive. You
might want to create your root filesystem partition on /dev/hda and
your swap partition on /dev/hdb, for example. In order to do so just
run fdisk or cfdisk once for each drive.

In Linux, partitions are given a name based on the drive which they
belong to. For example, the first partition on the drive /dev/hda is
/dev/hda1, the second is /dev/hda2, and so on. If you have any logical
partitions, they are numbered starting with /dev/hda5, /dev/hda6 and
so on up.

Note: You should not create or delete partitions for operating
systems other than Linux with Linux fdisk or cfdisk. That is, don't
create or delete MS-DOS partitions with this version of fdisk; use
MS-DOS's version of FDISK instead. If you try to create MS-DOS
partitions with Linux fdisk, chances are MS-DOS will not recognize
the partition and not boot correctly.

Here's an example of using fdisk. Here, we have a single MS-DOS
partition using 61693 blocks on the drive, and the rest of the drive
is free for Linux. (Under Linux, one block is 1024 bytes. Therefore,
61693 blocks is about 61 megabytes.) We will create just two
partitions in this tutorial example, swap and root. You should
probably extend this to four Linux partitions in line with the
recommendations above: one for swap, one for the root filesystem, one
for system software, and a home directory area.

First, we use the ``p'' command to display the current partition
table. As you can see, /dev/hda1 (the first partition on /dev/hda) is
a DOS partition of 61693 blocks.
Command (m for help): p
Disk /dev/hda: 16 heads, 38 sectors, 683 cylinders
Units = cylinders of 608 * 512 bytes

Device Boot Begin Start End Blocks Id System
/dev/hda1 * 1 1 203 61693 6 DOS 16-bit >=32M

Command (m for help):

Next, we use the ``n'' command to create a new partition. The Linux
root partition will be 80 megs in size.
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p

Here we're being asked if we want to create an extended or primary
partition. In most cases you want to use primary partitions, unless
you need more than four partitions on a drive. See the section
``Repartitioning'', above, for more information.
Partition number (1-4): 2
First cylinder (204-683): 204
Last cylinder or +size or +sizeM or +sizeK (204-683): +80M

The first cylinder should be the cylinder AFTER where the last
partition left off. In this case, /dev/hda1 ended on cylinder 203, so
we start the new partition at cylinder 204.

As you can see, if we use the notation ``+80M'', it specifies a
partition of 80 megs in size. Likewise, the notation ``+80K'' would
specify an 80 kilobyte partition, and ``+80'' would specify just an 80
byte partition.
Warning: Linux cannot currently use 33090 sectors of this partition

If you see this warning, you can ignore it. It is left over from an
old restriction that Linux filesystems could only be 64 megs in size.
However, with newer filesystem types, that is no longer the case...
partitions can now be up to 4 terabytes in size.

Next, we create our 10 megabyte swap partition, /dev/hda3.
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p

Partition number (1-4): 3
First cylinder (474-683): 474
Last cylinder or +size or +sizeM or +sizeK (474-683): +10M

Again, we display the contents of the partition table. Be sure to
write down the information here, especially the size of each partition
in blocks. You need this information later.
Command (m for help): p
Disk /dev/hda: 16 heads, 38 sectors, 683 cylinders
Units = cylinders of 608 * 512 bytes

Device Boot Begin Start End Blocks Id System
/dev/hda1 * 1 1 203 61693 6 DOS 16-bit >=32M
/dev/hda2 204 204 473 82080 83 Linux native
/dev/hda3 474 474 507 10336 83 Linux native

Note that the Linux swap partition (here, /dev/hda3) has type ``Linux
native''. We need to change the type of the swap partition to ``Linux
swap'' so that the installation program will recognize it as such. In
order to do this, use the fdisk ``t'' command:
Command (m for help): t
Partition number (1-4): 3
Hex code (type L to list codes): 82

If you use ``L'' to list the type codes, you'll find that 82 is the
type corresponding to Linux swap.

To quit fdisk and save the changes to the partition table, use the
``w'' command. To quit fdisk WITHOUT saving changes, use the ``q''
command.

After quitting fdisk, the system may tell you to reboot to make sure
that the changes took effect. In general there is no reason to reboot
after using fdisk---modern versions of fdisk and cfdisk are smart
enough to update the partitions without rebooting.
_________________________________________________________________

7.5.3. Post-partition steps

After you've edited the partition tables, your installation program
should look at them and offer to enable your swap partition for you.
Tell it yes.

(This is made a question, rather than done automatically, on the off
chance that you're running a dual-boot system and one of your
non-Linux partitions might happen to look like a swap volume.)

Next the program will ask you to associate Linux filesystem names
(such as /, /usr, /var, /tmp, /home, /home2, etc.) with each of the
non-swap partitions you're going to use.

There is only one hard and fast rule for this. There must be a root
filesystem, named /, and it must be bootable. You can name your other
Linux partitions anything you like. But there are some conventions
about how to name them which will probably simplify your life later
on.

Earlier on I recommended a basic three-partition setup including a
small root, a medium-sized system-software partition, and a large
home-directory partition. Traditionally, these would be called /,
/usr, and /home. The counterintuitive `/usr' name is a historical
carryover from the days when (much smaller) Unix systems carried
system software and user home directories on a single non-root
partition. Some software depends on it.

If you have more than one home-directory area, it's conventional to
name them /home, /home2, /home3, etc. This may come up if you have two
physical disks. On my personal system, for example, the layout
currently looks like this:
Filesystem 1024-blocks Used Available Capacity Mounted on
/dev/sda1 30719 22337 6796 77% /
/dev/sda3 595663 327608 237284 58% /usr
/dev/sda4 1371370 1174 1299336 0% /home
/dev/sdb1 1000949 643108 306130 68% /home2

The second disk (sdb1) isn't really all /home2; the swap partitions on
sda and sdb aren't shown in this display. But you can see that /home
is the large free area on sda and /home2 is the user area of sdb.

If you want to create an partition for scratch, spool, temporary,
mail, and news files, call it /var. Otherwise you'll probably want to
create a /usr/var and create a symbolic link named /var that points
back to it (the installation program may offer to do this for you).
_________________________________________________________________

7.6. Installing software packages

Once you've gotten past preparing your partitions, the remainder of
the installation should be almost automatic. Your installation program
(whether EGA or X-based) will guide you through a series of menus
which allow you to specify the CD-ROM to install from, the partitions
to use, and so forth.

Here we're not going to document many of the specifics of this stage
of installation. It's one of the parts that varies most between Linux
distributions (vendors traditionally compete to add value here), but
also the simplest part. And the installation programs are pretty much
self-explanatory, with good on-screen help.
_________________________________________________________________

7.7. After package installations

After installation is complete, and if all goes well, the installation
program will walk you through a few options for configuring your
system before its first boot from hard drive.
_________________________________________________________________

7.7.1. LILO, the LInux LOader

LILO (which stands for LInux LOader) is a program that will allow you
to boot Linux (as well as other operating systems, such as MS-DOS)
from your hard drive.

You may be given the option of installing LILO on your hard drive.
Unless you're running OS/2, answer `yes'. OS/2 has special
requirements; see [62]Custom LILO Configuration below.

Installing LILO as your primary loader makes a separate boot diskette
unnecessary; instead, you can tell LILO at each boot time which OS to
boot.
_________________________________________________________________

7.7.2. Making a production boot disk (optional)

You may also be given the chance to create a ``standard boot disk'',
which you can use to boot your newly-installed Linux system. (This is
an older and slightly less convenient method which assumes that you
will normally boot DOS, but use the boot disk to start Linux.)

For this you will need a blank, high-density MS-DOS formatted diskette
of the type that you boot with on your system. Simply insert the disk
when prompted and a boot diskette will be created. (This is not the
same as an installation bootdisk, and you can't substitute one for the
other!)
_________________________________________________________________

7.7.3. Miscellaneous system configuration

The post-installation procedure may also take you through several menu
items allowing you to configure your system. This includes specifying
your modem and mouse device, as well as your time zone. Follow the
menu options.

It may also prompt you to create user accounts or put a password on
the root (administration) account. This is not complicated and you can
usually just walk through the screen instructions.
_________________________________________________________________

8. Booting Your New System

If everything went as planned, you should now be able to boot Linux
from the hard drive using LILO. Alternatively, you should be able to
boot your Linux boot floppy (not the original bootdisk floppy, but the
floppy created after installing the software). After booting, login as
root. Congratulations! You have your very own Linux system.

If you are booting using LILO, try holding down shift or control
during boot. This will present you with a boot prompt; press tab to
see a list of options. In this way you can boot Linux, MS-DOS, or
whatever directly from LILO.
_________________________________________________________________

9. After Your First Boot

You should now be looking at the login prompt of a new Linux, just
booted from your hard drive. Congratulations!
_________________________________________________________________

9.1. Beginning System Administratration

Depending on how the installation phase went, you may need to create
accounts, change your hostname, or (re)configure X at this stage.
There are many more things you could set up and configure, including
backup devices, SLIP/PPP links to an Internet Service Provider, etc.

A good book on UNIX systems administration should help. (I suggest
Essential Systems Administration from O'Reilly and Associates.) You
will pick these things up as time goes by. You should read various
other Linux HOWTOs, such as the NET-3-HOWTO and Printing-HOWTO, for
information on other configuration tasks.
_________________________________________________________________

9.2. Custom LILO Configuration

LILO is a boot loader, which can be used to select either Linux,
MS-DOS, or some other operating system at boot time. Chances are your
distribution automatically configured LILO for you during the
installation phase (unless you're using OS/2, this is what you should
have done). If so, you can skip the rest of this section.

If you installed LILO as the primary boot loader, it will handle the
first-stage booting process for all operating systems on your drive.
This works well if MS-DOS is the only other operating system that you
have installed. However, you might be running OS/2, which has its own
Boot Manager. In this case, you want OS/2's Boot Manager to be the
primary boot loader, and use LILO just to boot Linux (as the secondary
boot loader).

An important gotcha for people using EIDE systems: due to a BIOS
limitation, your boot sectors for any OS have to live on one of the
first two physical disks. Otherwise LILO will hang after writing "LI",
no matter where you run it from.

If you have to configure LILO manually, this will involve editing the
file /etc/lilo.conf. Below we present an example of a LILO
configuration file, where the Linux root partition is on /dev/hda2,
and MS-DOS is installed on /dev/hdb1 (on the second hard drive).
# Tell LILO to install itself as the primary boot loader on /dev/hda.
boot = /dev/hda
# The boot image to install; you probably shouldn't change this
install = /boot/boot.b

# The stanza for booting Linux.
image = /vmlinuz # The kernel is in /vmlinuz
label = linux # Give it the name "linux"
root = /dev/hda2 # Use /dev/hda2 as the root filesystem
vga = ask # Prompt for VGA mode
append = "aha152x=0x340,11,7,1" # Add this to the boot options,
# for detecting the SCSI controller

# The stanza for booting MS-DOS
other = /dev/hdb1 # This is the MS-DOS partition
label = msdos # Give it the name "msdos"
table = /dev/hdb # The partition table for the second drive

Once you have edited the /etc/lilo.conf file, run /sbin/lilo as root.
This will install LILO on your drive. Note that you must rerun
/sbin/lilo anytime that you recompile your kernel in order to point
the boot loader at it properly (something that you don't need to worry
about just now, but keep it in mind).

Note how we use the append option in /etc/lilo.conf to specify boot
parameters as we did when booting the bootdisk.

You can now reboot your system from the hard drive. By default LILO
will boot the operating system listed first in the configuration file,
which in this case is Linux. In order to bring up a boot menu, in
order to select another operating system, hold down shift or ctrl
while the system boots; you should see a prompt such as
Boot:

Here, enter either the name of the operating system to boot (given by
the label line in the configuration file; in this case, either linux
or msdos), or press tab to get a list.

Now let's say that you want to use LILO as the secondary boot loader;
if you want to boot Linux from OS/2's Boot Manager, for example. In
order to boot a Linux partition from OS/2 Boot Manager, unfortunately,
you must create the partition using OS/2's FDISK (not Linux's), and
format the partition as FAT or HPFS, so that OS/2 knows about it.
(That's IBM for you.)

In order to have LILO boot Linux from OS/2 Boot Manager, you only want
to install LILO on your Linux root filesystem (in the above example,
/dev/hda2). In this case, your LILO config file should look something
like:
boot = /dev/hda2
install = /boot/boot.b
compact

image = /vmlinuz
label = linux
root = /dev/hda2
vga = ask

Note the change in the boot line. After running /sbin/lilo you should
be able to add the Linux partition to Boot Manager. This mechanism
should work for boot loaders used by other operating systems as well.
_________________________________________________________________

10. Administrivia

10.1. Terms of Use

This document is copyright 1998 by Eric S. Raymond. You may use,
disseminate, and reproduce it freely, provided you:

* Do not omit or alter this copyright notice (you may translate it)
* Do not omit or alter or omit the version number and date.
* Do not omit or alter the document's pointer to the current WWW
version.
* Clearly mark any condensed, altered or versions as such.

These restrictions are intended to protect potential readers from
stale or mangled versions. If you think you have a good case for an
exception, ask me.
_________________________________________________________________

10.2. Acknowledgements

My grateful acknowledgement to Matt D. Welsh, who originated this
HOWTO. I removed much of the Slackware-specific content and refocused
the remainder of the document on CD-ROM installation, but a
substantial part of the content is still his.

The 4.1 version was substantially improved by some suggestions from
David Shao <[email protected]>.

References

1. http://www.tuxedo.org/~esr/
2. Installation-HOWTO.html#AEN29
3. Installation-HOWTO.html#AEN31
4. Installation-HOWTO.html#AEN35
5. Installation-HOWTO.html#AEN54
6. Installation-HOWTO.html#AEN59
7. Installation-HOWTO.html#AEN67
8. Installation-HOWTO.html#AEN74
9. Installation-HOWTO.html#AEN80
10. Installation-HOWTO.html#AEN84
11. Installation-HOWTO.html#AEN152
12. Installation-HOWTO.html#AEN162
13. Installation-HOWTO.html#AEN165
14. Installation-HOWTO.html#AEN175
15. Installation-HOWTO.html#AEN180
16. Installation-HOWTO.html#AEN186
17. Installation-HOWTO.html#AEN193
18. Installation-HOWTO.html#AEN204
19. Installation-HOWTO.html#AEN225
20. Installation-HOWTO.html#AEN227
21. Installation-HOWTO.html#AEN244
22. Installation-HOWTO.html#AEN265
23. Installation-HOWTO.html#AEN327
24. Installation-HOWTO.html#AEN365
25. Installation-HOWTO.html#AEN524
26. Installation-HOWTO.html#AEN528
27. Installation-HOWTO.html#AEN545
28. Installation-HOWTO.html#AEN553
29. Installation-HOWTO.html#AEN556
30. Installation-HOWTO.html#AEN563
31. Installation-HOWTO.html#AEN601
32. Installation-HOWTO.html#AEN603
33. Installation-HOWTO.html#AEN616
34. http://www.linuxdoc.org/
35. http://www.linuxdoc.org/HOWTO/Installation-HOWTO.html
36. http://www.linuxdoc.org/HOWTO/INFO-SHEET.html
37. http://www.linuxdoc.org/HOWTO/META-FAQ.html
38. http://www.paranoia.com/~vax/boot.html
39. http://www.linuxdoc.org/
40. http://www.linuxdoc.org/HOWTO/Installation-HOWTO.html
41. mailto:[email protected]
42. http://www.varesearch.com/
43. http://members.tripod.com/~algolog/lnxchk.htm
44. http://www.linuxdoc.org/HOWTO/Hardware-HOWTO.html
45. http://www.linuxdoc.org/HOWTO/INFO-SHEET.html
46. http://www.linuxdoc.org/HOWTO/XFree86-HOWTO.html
47. http://www.linuxdoc.org/HOWTO/CDROM-HOWTO.html
48. http://www.linux-m68k.org/pub/faq/faq.html
49. http://www.linuxdoc.org/HOWTO/Distribution-HOWTO.html
50. http://metalab.unc.edu/pub/Linux/distributions/
51. http://www.linuxdoc.org/HOWTO/BootPrompt-HOWTO.html
52. http://www.linuxdoc.org/HOWTO/Busmouse-HOWTO.html
53. http://www.linuxdoc.org/HOWTO/Bootdisk-HOWTO.html
54. http://www.linuxdoc.org/HOWTO/mini/Linux+DOS+Win95+OS2.html
55. http://www.linuxdoc.org/HOWTO/mini/Linux+Win95.html
56. http://www.linuxdoc.org/HOWTO/mini/Linux+NT-Loader.html
57. http://www.gnu.org/software/parted
58. http://metalab.unc.edu/pub/Linux/system/install
59. http://www.linuxdoc.org/HOWTO/mini/Partition.html
60. ftp://metalab.unc.edu/pub/Linux/docs/HOWTO/unmaintained/mini/Swap-Space
61. http://www.linuxdoc.org/HOWTO/mini/Large-Disk.html
62. Installation-HOWTO.html#CUSTOM-LILO