# This is the vanprod.conf file.  vanprod will re-read this file
# when it receives a HUP signal.
# Typical unix config file rules apply here.  You may use whitespace
# before and/or after the = signs or you may omit the whitespace around
# the = altogether, your choice -- vanprod won't care. Blank lines and
# everything following a # character is treated as a comment.
# Leading and trailing whitespace are stripped out as the file is parsed
# The variables here should all be lower case.  vanprod does not use
# upper case variables.  You do not need to quote any values,
# free form strings are allowed.  The value terminates with a new line
# character, unless a # is encountered first, which may be preceeded by
# optional whitespace.


# tty defines where your Vantage Pro is connected

tty = /dev/ttyS1

# which facility would you like to use for syslog

facility = local0

# The working directory for vanprod.  The currentobs, dailyobs,
# and extremes files will be written here

directory = /some/path/to/weather

# Where do you want the daemon to write a file containing
# it pid?

piddir = /var/run

# This defines whether or not to update weather underground
# If this is set to 1 yes or true, vanprod will attempt to send data to
# weather underground in normal mode.  If set to 2 or rapid, rapid fire
# mode will be enabled.  Any other value here will be interpreted as false.

send_to_wu = 1

# Same as above, only for APRSWXNET/CWOP -- Note rapid fire mode not supported.
# If you are not familiar with what this is and for info on signing up,
# see http://www.wxqa.com

send_to_cwop = 1

# This is a comma seperate list of the minutes past the hour that you wish
# to send an update to weatherunderground if you are using normal mode updates.

update_wu_min = 0,5,10,15,20,25,30,35,40,45,50,55

# CWOP updates are now coded to occur every 10 minutes if you are sending to CWOP.
# This is in accordance with guidelines from the CWOP program.  Set this to the
# value of the minute during each 10 when you should send your updates.
# Your update minute should be equal to the last digit in your CWOP ID.
# For hams, use your station ID assigned to you from MADIS.
# Example: My station ID is AR536, so my setting for this value would be 6.
# This will result in updates being sent to CWOP at 6, 16, 26, 36, 46,
# and 56 past the hour.

update_cwop_min = 3

# This is for your station ID on weather underground

wu_id =

# Your weather underground password

wu_password =

# Your ham callsign or CWOP ID for APRSWXNET/CWOP  Use upper case in the value
# I do recommend that you use an elevation of 0 on your Vantage Pro console,
# especially if you are reporting or plan to report to APRSWXNET/CWOP.  The
# number they expect to have provided is the altimeter.  The only way to have
# the Vantage Pro report this is by using 0 for your elevation.
# See the section OTHER NOTES AND THOUGHTS in the vanprod documentation
# for details about this.

callsign = CW9999

# Your cwop password if you are a ham operator and have one.
# This password allows packets coming from licensed ham operators to be
# validated and passed on to an RF (amateur packet radio) network by an
# Igate.  If you are a licensed ham and would like to enable the possibility
# for your weather data to be broadcast on a local packet radio network,
# set your passcode here.  To obtain your passcode, you may send your
# callsign to [email protected] or I will be happy to provide
# this information for you.  Again , just e-mail your callsign to me at
# [email protected].  73 de N5KJT
# Folks using a CW#### Id (i.e. non-hams) should leave this set to  -1

cwop_password = -1

# This is the order in which a connection attempt is made to the cwop servers
# if you are sending to cwop.  Using cwop.aprs.net or rotate.aprs.net first
# is reccommended.  cwop.aprs.net is primarily for non-hams and rotate.aprs.net
# is primarily for hams.
# The software will automatically fail over to the next in the list if one
# server is found to not be responding correctly.  If you wish, you may
# change the order of cwop1 through cwop4.  Also, you may add as many entries
# here as you like.  The servers you list here must accept connections on port
# 14580.

cwop0 = cwop.aprs.net
cwop1 = first.aprs.net  # College Station, TX - Gerry Creager, N5JXS
cwop2 = second.aprs.net # Claremont, CA - Greg Noneman, WB6ZSU
cwop3 = third.aprs.net  # Dallas, TX - Jason Winningham, KG4WSV
cwop4 = rotate.aprs.net

# Your latitude and longitude.  These are used for APRSWXNET/CWOP reports.
# The format for latitude is exactly 4 digits followed by a decimal then
# 2 digits followed by an uppercase hemisphere designator.  The digits are ddmm.mm
# where d is degrees m is minutes carried out to a resolution of 1/100th
# (.01) of a minute.  Be sure to insert leading zeros as needed.
# The longitude is identical except there are 3 digits required for the
# degrees, so it becomes dddmm.mm.  If you make a formatting error,
# the daemon will write a warning to your syslog and not send any data to
# APRSWXNET/CWOP.
# This follows the LORAN format if you wish to find more details.

lat = ddmm.mmN
lon = dddmm.mmW

# This variable allows you to temporarily disable a sensor or sensors
# from being included in updates sent to Weatherunderground and CWOP
# and stored in the RRDs.  This variable is used as a bitmask to exclude
# the various sensors. The values for the sensors are as follows:
# 1 = Outdoor Temperature
# 2 = Barometer
# 4 = Wind Speed
# 8 = Wind Direction
# 16 = Outdoor Humidity
# 32 = Rainfall
# To exclude more than one sensor add the values for the sensors together.
# For example:  To exclude Wind Speed and Direction set this to 12.
# To exclude Temperature and Humidity set it to 17.
# The setting of this variable only affects updates to WU, CWOP, and the RRDs.
# It has no impact on the text files written by the daemon or the values
# stored in the mysql database.

sensor_exclude = 0

# This setting is for your barometer offset expressed in millibars.
# (.01 inches of mercury = .338637526 millibars)  This only affects
# calculations within the daemon and not the console.  Any offset you have set
# on the console is ignored by the daemon and needs to be set here to be seen
# by the daemon.  This value, of course, can be positive or negative.

bar_offset = 0

# how many of the daily observations files to keep.  Set to -1 if you
# want to keep them forever or clean them up yourself.

oldobs = 7

# type of database we're talking to

db = mysql

# The name of the database

db_name = weather

# name of db user that can add records

db_user =

# password for user above

db_password =

# name of db table for values to be inserted

db_table = reports

# If you have a wireless Vantage Pro with extra sensors, you can assign
# some meaningful descriptions here by assigning values to the different
# transmitter ID's (tid0 through tid7)  The factory default for tid0
# is the Integrated Sensor Suite, although the Davis documentation
# indicates you can change this.  This is used to monitor the battery
# level in these transmitters.

tid0 = ISS  # Integrated Sensor Suite - Factory default
tid1 = ID 2
tid2 = ID 3
tid3 = ID 4
tid4 = ID 5
tid5 = ID 6
tid6 = ID 7
tid7 = ID 8

# This controls how often action is taken in response to an alarm.  The value
# should be expressed in seconds as it will be internally adjusted by the loop
# ratio.

alarm_interval = 300

# This the ratio of the number of passes through the data gathering loop to
# 1 second of real time.  This value allows the daemon to more accurately
# track the values that are time based in some manner.  There isn't much
# effect on shorter intervals like the average wind direction, but for longer
# intervals such as the barometer trend, or 24 hour
# rainfall totals, the error introduced can be easily noticed.
# (OK, so maybe I'm a perfectionist.)
# This value should be carried out to 3 decimal places.

loop_ratio = 1.974

# This should be set to an integer value that represents how many seconds you
# need to slow the daemon down.  If your loop ratio is less than 1, I highly
# recommend that you set this to at least 1 so that the daemon will not make
# more than 1 loop per second.  Running too fast may produce unpredictable
# performance.

slow = 0

# This is where you can set thresholds for the various "silent" alarms.
# These settings are independant of the alarms set on the Vantage Pro console.

bar_fall_q = -.09
bar_rise_q = .09
low_intemp_q = 40
hi_intemp_q = 80
low_inhum_q = 20
hi_inhum_q = 90
rain1_q = .75
rainm15_q = .25
rain24_q = 1.75
storm_q = 2.25
low_outtemp_q = -5
hi_outtemp_q = 105
windsp_q = 50
avgwindsp_q = 30
low_outdew_q = -15
hi_outdew_q = 70
heat_q = 105
chill_q = 0

# This is where you can define a script that vanprod will execute whenever an
# alarm threshold (silent or console) is crossed.  This is in addition to
# messages that will be written to your syslog.  Two arguments will be passed
# to this script, the designator for which value has triggered the alarm, and
# the current value.  Example: for a low outdoor temperature alarm, the
# arguments passed would be low_outtemp value.  The "designators" are simply
# the threshold variables without the _q on the end.  If you have the 15 minute
# rainfall (flash flood) alarm set on your Vantage Pro console, when this
# triggers, it will be sent to your script with a designator of ff.  Standard
# out and Standard error will be captured from this script, and any output
# that is captured will be written to your syslog.

alarm_action =

You are viewing proxied material from ftp.icm.edu.pl. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.