Subj : Re: Sent to Staging
To   : C.G. Learn
From : Nick Andre
Date : Thu Mar 09 2017 02:22 am

On 08 Mar 17  20:55:51, C.G. Learn said the following to Joe Delahaye:

CL>  JD> Is Binkd loaded? Unless you have DB configured to load binkd as it sta
CL>  JD> up, you will have to seperately start binkd.
CL>
CL> Yes, Binkd is loaded. I can see it call out, but it never sends anything. T
CL> hub calls me also, and it never picks anything up. I get my packets for ech
CL> mail, but net mail just stays there as a packet, but the actual *.msg in th
CL> netmail folder dissapears.

First of all, lets verify that the BinkD mailbox directory exists for the
destination. If the mailbox/staging directory does not exist, no mail can
be correctly exchanged. Lets shut down both D'Bridge and BinkD.

ie. if the destination is 1:229/426 and your QUEUE directory is \DB\QUEUE,
then in DOS, CD \ your way to your D'Bridge directory and type:

DBUTIL QNAME 1:229/426

MD \DB\QUEUE\D-00106D.0BU

Note the output of DBUTIL QNAME. That makes up the mailbox name, just add the
"D-" infront of it. In this case, 1:229/426 equals D-00106D.0BU.

While we're at it, lets also make sure nothing is being put on "Hold" status
by BinkD. CD \DB\DATA and type:

DEL /S *.HLD
DEL /S *.TRY

This will delete the control files that tell BinkD to put stuff on hold, and
also resets the number of "tries" (attempts) to contact destination systems.

Restart both D'Bridge and BinkD. Watch very carefully on the next connection
attempt, or force one out by doing a POLL to the remote system.

If mail is still not being exchanged, then verify in the logs that when the
system in question connects with yours, that the "domains" are matching.
BinkD uses whats known as "5 dimentional" addressing where the domain portion
MUST match with the remote system otherwise no mail will be exchanged.  The
confusing part is that in 5D addressing, it is not necessarily an actual
Internet domain name, but rather moreso a mutually-agreed-upon domain.

In the BinkD log, if the destination is 1:229/426 and you see something like
"1:229/[email protected] busy or N/A" when a connection is established, then
uh-oh, the domain is not being correctly matched and no mail will be
exchanged in the session.

In D'Bridge CONFIG-INTERNET, you see that each line in the BINKD SESSIONS
screen begins with the Fido address, a space, and the domain name. In the case
of Fidonet, this should be set to "fidonet". However, a lot of systems in
Fidonet may not necessarily specify "fidonet" as the presented domain in a
BinkD session. Very carefully watch your log and if the remote system presents
something else, lets say, fidonet.org, then in Config-Internet, you will ARROW
DOWN to ADDITIONAL OPTIONS and specify:

domain fidonet.org alias-for fidonet

Exit Config-Internet, and restart both D'Bridge and BinkD once again. Force
another connection to the remote system, paying attention to the connection
log. Note that I strongly recommend NOT specifying "dot" notation in 5D
domains in CONFIG-INTERNET. Keep Fidonet as "fidonet". When you start
getting into mixing and matching the variations of "fidonet", it becomes a
bit difficult to troubleshoot domain-related problems going forward.

If these two suggestions - The mailbox directory and the BinkD domains - if
these two do NOT solve the problem, then let me know.

Nick

--- Renegade vY2Ka2
* Origin: Joey, do you like movies about gladiators? (1:229/426)

You are viewing proxied material from cvs.synchro.net. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.