Introduction
Introduction Statistics Contact Development Disclaimer Help
View Source
# ACCULOGIC, INC.
SIDE-4/ PLUS
+------------------------------------------------------------+
|------------------------------------------------------------|
| Data bus: | 16-bit, ISA |
|-------------------+----------------------------------------|
| Size: | Half-length, full-height card |
|-------------------+----------------------------------------|
| Hard drives | Two IDE(AT) drives |
| supported: | |
|-------------------+----------------------------------------|
| Floppy drives | Two 360KB, 720KB, 1.2MB or 1.44MB |
| supported: | drives |
+------------------------------------------------------------+
IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Location |
|---------------------------------------------+--------------|
| 34-pin control cable connector-floppy drive | J1 |
|---------------------------------------------+--------------|
| 4-pin connector-drive active LED | J2 |
|---------------------------------------------+--------------|
| 40-pin AT Interface (IDE) connector | J3 |
|---------------------------------------------+--------------|
| 9-pin serial port 2-internal | J4 |
|---------------------------------------------+--------------|
| 15-pin game port-internal | J5 |
|---------------------------------------------+--------------|
| 9-pin serial port 1-external | J6 |
|---------------------------------------------+--------------|
| 25-pin parallel port-external | J7 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER CONFIGURABLE SETTINGS |
|------------------------------------------------------------|
| Function | Location | Setting |
|------------------------------------+----------+------------|
| » | I/O Channel Ready signal | JP4 | open |
| | disabled | | |
|---+--------------------------------+----------+------------|
| | I/O Channel Ready signal | JP4 | closed |
| | enabled | | |
|---+--------------------------------+----------+------------|
| » | Floppy drive enabled | JP5 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Floppy drive disabled | JP5 | pins 2 & 3 |
| | | | closed |
|---+--------------------------------+----------+------------|
| » | Floppy drive port address is | JP6 | pins 1 & 2 |
| | 3F0-3F7h | | closed |
|---+--------------------------------+----------+------------|
| | Floppy drive port address is | JP6 | pins 2 & 3 |
| | 370-377h | | closed |
|---+--------------------------------+----------+------------|
| » | Single speed floppy drives | JP7 | pins 1 & 2 |
| | supported | | closed |
|---+--------------------------------+----------+------------|
| | Dual speed floppy drives | JP7 | pins 2 & 3 |
| | supported | | closed |
|---+--------------------------------+----------+------------|
| » | Hard drive enabled | JP8 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Hard drive disabled | JP8 | pins 2 & 3 |
| | | | closed |
|---+--------------------------------+----------+------------|
| » | IDE select mode enabled | JP9 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Not used | JP9 | open |
|---+--------------------------------+----------+------------|
| » | Hard drive port address is | JP10 | pins 1 & 2 |
| | 1F0-1F7h | | closed |
|---+--------------------------------+----------+------------|
| | Hard drive port address is | JP10 | pins 2 & 3 |
| | 170-177h | | closed |
|---+--------------------------------+----------+------------|
| » | Not used | JP11 | open |
|---+--------------------------------+----------+------------|
| » | IRQ14 normal | JP12 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | IRQ14 delayed until ACTIVE- | JP12 | pins 2 & 3 |
| | signal is removed | | closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL & PARALLEL PORT CONFIGURATIONS |
|------------------------------------------------------------|
| Function | Location | Setting |
|------------------------------------+----------+------------|
| » | Serial port 1 (CN6) enabled | JP13 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Serial port 1 (CN6) disabled | JP13 | pins 2 & 3 |
| | | | closed |
|---+--------------------------------+----------+------------|
| » | Serial port 1 (CN6) set to | JP14 | pins 1 & 2 |
| | COM1 | | closed |
|---+--------------------------------+----------+------------|
| | Serial port 1 (CN6) set to | JP14 | pins 2 & 3 |
| | COM3 | | closed |
|---+--------------------------------+----------+------------|
| » | Serial port 2 (CN4) enabled | JP15 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Serial port 2 (CN4) disabled | JP15 | pins 2 & 3 |
| | | | closed |
|---+--------------------------------+----------+------------|
| » | Serial port 2 (CN4) set to | JP16 | pins 1 & 2 |
| | COM2 | | closed |
|---+--------------------------------+----------+------------|
| | Serial port 2 (CN4) set to | JP16 | pins 2 & 3 |
| | COM4 | | closed |
|---+--------------------------------+----------+------------|
| » | Parallel port (CN7) enabled | JP17 | pins 1 & 2 |
| | | | closed |
|---+--------------------------------+----------+------------|
| | Parallel port (CN7) disabled | JP17 | pins 2 & 3 |
| | | | closed |
|---+--------------------------------+----------+------------|
| » | Parallel port (CN7) address is | JP18 | pins 1 & 2 |
| | LPT1 | | closed |
|---+--------------------------------+----------+------------|
| | Parallel port (CN7) address is | JP18 | pins 2 & 3 |
| | LPT2 | | closed |
+------------------------------------------------------------+
You are viewing proxied material from bitreich.org. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.