Introduction
Introduction Statistics Contact Development Disclaimer Help
View Source
# ACCULOGIC, INC.
SIDE-4
+------------------------------------------------------------+
|------------------------------------------------------------|
| Data bus: | 16-bit, ISA |
|-------------------+----------------------------------------|
| Size: | Half-length, full-height card |
|-------------------+----------------------------------------|
| Hard drives | Two IDE(AT) drives |
| supported: | |
|-------------------+----------------------------------------|
| Floppy drives | Two 360KB, 720KB, 1.2MB or 1.44MB |
| supported: | drives |
+------------------------------------------------------------+
IMG 1
+------------------------------------------------------------+
| CONNECTIONS |
|------------------------------------------------------------|
| Function | Location |
|---------------------------------------------+--------------|
| 34-pin control cable connector-floppy drive | J1 |
|---------------------------------------------+--------------|
| 4-pin connector-Drive Active LED | J2 |
|---------------------------------------------+--------------|
| 9-pin serial port 1-external | J3 |
|---------------------------------------------+--------------|
| 25-pin parallel port-external | J4 |
|---------------------------------------------+--------------|
| 40-pin AT Interface (IDE) connector | J5 |
|---------------------------------------------+--------------|
| 9-pin serial port 2-internal | J8 |
+------------------------------------------------------------+
+------------------------------------------------------------+
| IRQ14 STATUS |
|------------------------------------------------------------|
| Function | W3/Pins 1 & | W3/Pins 3 & |
| | 2 | 4 |
|--------------------------------+-------------+-------------|
| » | IRQ14 normal | open | closed |
|---+----------------------------+-------------+-------------|
| | IRQ14 delayed until | closed | open |
| | ACTIVE- signal is removed | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| USER CONFIGURABLE SETTINGS |
|------------------------------------------------------------|
| Function | Location | Setting |
|---------------------------------------+----------+---------|
| » | Floppy drive enabled | W4A | closed |
|---+-----------------------------------+----------+---------|
| | Floppy drive disabled | W4A | open |
|---+-----------------------------------+----------+---------|
| » | Floppy drive port address is | W4B | open |
| | 3F0-3F7h | | |
|---+-----------------------------------+----------+---------|
| | Floppy drive port address is | W4B | closed |
| | 370-377h | | |
|---+-----------------------------------+----------+---------|
| » | Single speed floppy drives | W5 | open |
| | supported | | |
|---+-----------------------------------+----------+---------|
| | Dual speed floppy drives | W5 | closed |
| | supported | | |
|---+-----------------------------------+----------+---------|
| » | Hard drive enabled | W9 | closed |
|---+-----------------------------------+----------+---------|
| | Hard drive disabled | W9 | open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| PARALLEL PORT (CN4) CONFIGURATION |
|------------------------------------------------------------|
| CN4 | W8/jumper 1 | W8/jumper 2 |
|--------------------+-------------------+-------------------|
| LPT1 enabled | closed | open |
|--------------------+-------------------+-------------------|
| LPT2 enabled | closed | closed |
|--------------------+-------------------+-------------------|
| Disabled | open | open |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT 1 (CN3) CONFIGURATION |
|------------------------------------------------------------|
| Function | W8/Jumper 3 | W8/Jumper 4 |
|--------------------------------+-------------+-------------|
| » | Serial port 1 set to COM1 | closed | open |
| | (3F8h) | | |
|---+----------------------------+-------------+-------------|
| | Serial port 1 set to COM3 | open | closed |
| | (3E8h) | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| SERIAL PORT 2 (CN8) CONFIGURATION |
|------------------------------------------------------------|
| Function | W8/Jumper 5 | W8/Jumper 6 |
|--------------------------------+-------------+-------------|
| » | Serial port 2 set to COM2 | closed | open |
| | (2F8h) | | |
|---+----------------------------+-------------+-------------|
| | Serial port 2 set to COM4 | open | closed |
| | (2E8h) | | |
+------------------------------------------------------------+
+------------------------------------------------------------+
| I/O PORT INTERRUPT REQUEST |
|------------------------------------------------------------|
| Function | Location | Setting |
|----------------------------------+----------+--------------|
| » | Parallel port (CN4) uses | W7 | pins 3 & 4 |
| | IRQ7 | | closed |
|---+------------------------------+----------+--------------|
| | Parallel port (CN4) uses | W7 | pins 1 & 2 |
| | IRQ5 | | closed |
|---+------------------------------+----------+--------------|
| » | Serial port 2 (CN8) uses | W7 | pins 5 & 6 |
| | IRQ3 | | closed |
|---+------------------------------+----------+--------------|
| | Serial port 2 (CN8) uses | W7 | pins 5 & 7 |
| | IRQ4 | | closed |
|---+------------------------------+----------+--------------|
| » | Serial port 1 (CN3) uses | W7 | pins 7 & 8 |
| | IRQ4 | | closed |
|---+------------------------------+----------+--------------|
| | Serial port 1 (CN3) uses | W7 | pins 6 & 8 |
| | IRQ3 | | closed |
+------------------------------------------------------------+
+------------------------------------------------------------+
| MISCELLANEOUS TECHNICAL NOTES |
|------------------------------------------------------------|
| This controller has no on-board software. |
+------------------------------------------------------------+
You are viewing proxied material from bitreich.org. The copyright of proxied material belongs to its original authors. Any comments or complaints in relation to proxied material should be directed to the original authors of the content concerned. Please see the disclaimer for more details.